IHS LOW VOLTAGE EQUIPMENT (Medical) (EU DIR 73/23/EEC)

LOW VOLTAGE EQUIPMENT (Medical) (EU DIR 73/23/EEC)

The IHS Low Voltage Equipment Standards Collection provides immediate access to a complete and always current standards solution so critical to the design control process – ensuring compliance to the European Union (EU) Directive (73/23/EEC). The Low Voltage Directive (LVD) applies to electrical equipment designed for use with a voltage rating of between 50 and 1000 V for alternating current, and between 75 and 1500 V for direct current, and whose primary safety risk is of an electrical nature. Manufacturers that sell and distribute electrical equipment to the European Union (EU) must provide the presumption of conformity with the Directives’ essential requirements, and are subject to conformity assessment audits involving a Notified Body. All electrical devices sold in the EU must have the CE Marking affixed to demonstrate compliance to the Directive. This collection enables subscribers to quickly search, view and print documents for archival or project reference, with confidence that it has the most up-to-date standards necessary to maintain compliance to EU Directive 73/23/EEC.

* Buy button is for individual document
Collection of Low Voltage Equipment Standards
LOW VOLTAGE EQUIPMENT (Medical) (EU DIR 73/23/EEC) Collection of more than 250 Low Voltage Equipment Standards ensuring compliance to the European Union (EU) Directive (73/23/EEC). Scope: See information above for scope. Benefits of Subscription Collections: • Broad technical resources in one place • 24/7 online access and searching • Daily content updates With an IHS subscription, you can access information immediately. IHS subscriptions are available via the Internet, DVD, intranet, or extranet.	Subscribe
Sampling of Documents in Low Voltage Equipment Collection
BS EN 61010-1 Safety requirements for electrical equipment for measurement, control, and laboratory use Scope: This part of IEC 61010 specifies general safety requirements for electrical equipment intended for professional, industrial process, and educational use, any of which may incorporate computing devices, as defined in a) to d) below, when used under the environmental conditions of 1.4.	Buy *
BS EN 60529 Degrees of Protection Provided by Enclosures Scope: Gives uniformity in methods of describing the protection provided by enclosures and in tests to prove various degrees of protection. Provides an optional extension of the IP code by an additional letter A-D, if the actual protection of persons against access to hazardous parts is higher than that indicated by the first characteristic numeral.	Buy *
BS EN 60950 Safety of Information Technology Equipment-CORR 13834: July 8, 2002; Scope: Provides designers with an appreciation of the underlying principles of safety requirements needed to deal with various potential hazards.	Buy *
BS EN 60204-1 Safety of Machinery - Electrical Equipment of Machines - Part 1: General Requirements-IEC 60204-1: 1997; Scope: Specifies general requirements for an individual machine as well as a group of machines operating in a coordinated manner for compliance with the essential safety requirements in annex 1 of Council Directive 89/392/EEC on machines. Fulfils the requirements of the Low Voltage Directive 73/23/EEC.	Buy *
BS EN 60439-1 Low-Voltage Switchgear and Controlgear Assemblies - Part 1: Type-Tested and Partially Type-Tested Assemblies-AMD 15206: June 30, 2004; IEC 60439-1: 1999 Scope: Gives requirements for type tested and partially type tested assemblies with rated voltage not exceeding 1000 V a.c. at frequencies not exceeding 1 kHz, or 1500 V d.c.	Buy *

Complete Document List For The Low Voltage Equipment Standards Collection
Source	Doc Number	Pub Date	Title
BSI	BS EN 41003	5/15/1999	Particular Safety Requirements for Equipment to Be Connected to Telecommunications Networks
BSI	BS EN 50065-4-2	1/24/2002	Signalling on low voltage electrical installations in the frequency range 3 kHz to 148,5 kHz Part 4-2: Low voltage decoupling filters - Safety requirements-AMD 14440: May 29, 2003;
BSI	BS EN 50083-1	9/15/1994	Cabled Distribution Systems for Television, Sound and Interactive Multimedia Signals Part 1: Safety Requirements-AMD 9972; May 1998;
BSI	BS EN 50085-1	3/15/1999	Cable Trunking and Cable Ducting Systems for Electrical Installations - Part 1: General Requirements-AMD 10512; January 2000;
BSI	BS EN 50085-2-3	8/15/2001	Cable Trunking Systems and Cable Ducting Systems for Electrical Installations - Part 2-3: Particular Requirements for Slotted Cable Trunking Systems Intended for Installation in Cabinets
BSI	BS EN 50086-1	4/15/1994	Specification for Conduit systems for cable management Part 1: General requirements-AMD 12052: November, 2000; CORR 13548: February 26, 2002; CORR 15466: March 31, 2004; CORR 15466: March 31, 2004; Supersedes BS 731-1:1952, BS 6099-1:1981 and BS 4568-2:1970
BSI	BS EN 50086-2-1	4/15/1996	Specification for Conduit systems for cable management Part 2: Particular requirements Section 2.1: Rigid conduit systems-AMD 10513: January 2000; CORR 13547: February 26, 2002
BSI	BS EN 50086-2-2	4/15/1996	Specification for Conduit systems for cable management Part 2: Particular requirements Section 2.2: Pliable conduit systems-AMD 10514: January 2000; CORR 13546: February 26, 2002
BSI	BS EN 50086-2-3	4/15/1996	Conduit Systems for Cable Management - Part 2: Particular Requirements - Section 2.3: Flexible Conduit Systems-CORR 13549; February 26, 2002
BSI	BS EN 50086-2-4	9/15/1994	Specification for Conduit Systems for Cable Management - Part 2: Particular Requirements Section 2.4: Conduit Systems Buried Underground-AMD 13550: March 13, 2002;
BSI	BS EN 50091-1	1/1/1993	Uninterruptable Power Systems (UPS) Part 1: General and Safety Requirements (E)-Replaced by 50091-1-1:1997
BSI	BS EN 50091-1-1	8/15/1997	Uninterruptible power systems (UPS) Part 1-1: General and safety requirements for UPS used in operator access areas-AMD 14309:June 3, 2003; CORR 15355:August 25, 2004; Replaces BS EN 50091-1:1993
BSI	BS EN 50091-1-2	3/15/1999	Uninterruptible Power Systems (UPS) Part 1-2: General and Safety Requirements for UPS Used in Restricted Access Locations-CORR 10753; April 2000
BSI	BS EN 50132-2-1	4/15/1998	Alarm Systems - CCTV Surveillance Systems for Use in Security Applications Part 2-1: Black and White Cameras
BSI	BS EN 50146	5/15/2000	Cable Ties for Electrical Installations
BSI	BS EN 50178	12/15/1998	Corr.1 Electronic Equipment for Use in Power Installations-CORR 10604; August 1999;
BSI	BS EN 50214	12/15/1998	Flexible Cables for Lifts-AMD 14203: February 12, 2004; CORR 10421; May 15, 1999; Supersedes BS 6977: 1991
BSI	BS EN 50250	1/1/2002	Conversion adaptors for industrial use
BSI	BS EN 50262	10/15/1999	Cable glands for electrical installations-AMD 13524: April 15, 2002; AMD 15520: February 21, 2005; Supersedes BS 6121-2:1989 and BS 6121-3:1990; Together with BS 6121-1:2005 supersedes BS 6121-1:1989
BSI	BS EN 50262	10/15/1999	Cable glands for electrical installations-AMD 13524: April 15, 2002; AMD 15520: February 21, 2005 Supersedes BS 6121-2:1989 and BS 6121-3:1990; Together with BS 6121-1:2005 supersedes BS 6121-1:1989
BSI	BS EN 50265-1	9/15/1999	Common Test Methods for Cables Under Fire Conditions - Test for Resistance to Vertical Flame Propagation for a Single Insulated Conductor or Cable - Part 1: Apparatus-Together with BS EN 50265-2-1 and BS EN 50265-2-2 Supersedes BS 4066-1: 1980 and BS 4066-2: 1989; Superseded by BS EN 60332-2-1:2004 and BS EN 60332-1-1:2004
BSI	BS EN 50265-2-1	9/15/1999	Common Test Methods for Cables Under Fire Conditions - Test for Resistance to Vertical Flame Propagation for a Single Insulated Conductor or Cable - Part 2-1: Procedures - 1 kW Pre-Mixed Flame-Supersedes BS 4066-1: 1980; Superseded by BS EN 60332-1-2:2004
BSI	BS EN 50265-2-2	9/15/1999	Common Test Methods for Cables Under Fire Conditions - Test for Resistance to Vertical Flame Propagation for a Single Insulated Conductor or Cable - Part 2-2: Procedures - Diffusion Flame-Supersedes BS 4066-2: 1989; Superseded by BS EN 60332-2-2:2004
BSI	BS EN 50266-1	8/15/2001	Common Test Methods for Cables under Fire Conditions - Test for Vertical Flame Spread of Vertically-Mounted Bunched Wires or Cables - Part 1: Apparatus-Together with BS EN 50266-2-1 Thru BS EN 502-2-5:2001 Supersedes BS 4066-3:1994;
BSI	BS EN 50266-2-1	8/15/2001	Common Test Methods for Cables under Fire Conditions - Test for Vertical Flame Spread of Vertically-Mounted Bunched Wires or Cables - Part 2-1: Procedures - Category A F/R-CORR 13887: September 30, 2002; Together with BS EN 50266-1, BS EN 50266-2-2 Thru BS EN 502-2-5: 2001 Supersedes BS 4066-3: 1994;
BSI	BS EN 50266-2-2	8/15/2001	Common Test Methods for Cables under Fire Conditions - Test for Vertical Flame Spread of Vertically-Mounted Bunched Wires or Cables - Part 2-2: Procedures - Category A-CORR 13849: September 30, 2002; Together with BS EN 50266-1, BS EN 50266-2-1, BS EN 50266-2-3 Thru BS EN 502-2-5: 2001 Supersedes BS 4066-3: 1994;
BSI	BS EN 50266-2-3	8/15/2001	Common Test Methods for Cables under Fire Conditions - Test for Vertical Flame Spread of Vertically-Mounted Bunched Wires or Cables - Part 2-3: Procedures - Category B-CORR 13854: September 30, 2002; Together with BS EN 50266-1, BS EN 50266-2-1, BS EN 50266-2-2, BS EN 50266-2-4 and BS EN 50266-2-5: 2001, Supersedes BS 4066-3: 1994;
BSI	BS EN 50266-2-4	8/15/2001	Common Test Methods for Cables under Fire Conditions - Test for Vertical Flame Spread of Vertically-Mounted Bunched Wires or Cables - Part 2-4: Procedures - Category C-CORR 13853: September 30, 2002; Together with BS EN 50266-1, BS EN 50266-2-1 Thru BS EN 50266-2-3 and BS EN 502-2-5: 2001 Supersedes BS 4066-3: 1994;
BSI	BS EN 50266-2-5	8/15/2001	Common Test Methods for Cables under Fire Conditions - Test for Vertical Flame Spread of Vertically-Mounted Bunched Wires or Cables - Part 2-5: Procedures - Small Cables - Category D-CORR 13850: September 30, 2002; Together with BS EN 50266-1, BS EN 50266-2-1 Thru BS EN 50266-2-4: 2001 Supersedes BS 4066-3: 1994;
BSI	BS EN 50267-1	9/15/1999	Common Test Methods for Cables under Fire Conditions - Tests on Gases Evolved During Combustion of Materials From Cables - Part 1: Apparatus-Supersedes BS 6425-1: 1990; Together with BS EN 50267-2-3 Supersedes BS 6425-2: 1993
BSI	BS EN 50267-2-1	9/15/1999	Common Test Methods for Cables Under Fire Conditions - Tests on Gases Evolved During Combustion of Materials From Cables - Part 2-1: Procedures - Determination of the Amount of Halogen Acid Gas-Together with BS EN 50267-1 Supersedes BS 6425-1: 1990
BSI	BS EN 50267-2-2	9/15/1999	Common Test Methods for Cables Under Fire Conditions - Tests on Gases Evolved During Combustion of Materials From Cables - Part 2-2: Procedures - Determination of Degree of Acidity of Gases for Materials by Measuring pH and Conductivity
BSI	BS EN 50267-2-3	9/15/1999	Common Test Methods for Cables Under Fire Conditions - Tests on Gases Evolved During Combustion of Materials From Cables - Part 2-3: Procedures - Determination of Degree of Acidity of Gases for Cables by Determination of the Weighted Average of pH and Conductivity-Together with BS EN 50267-1 Supersedes BS 6425-2: 1993
BSI	BS EN 50268-1	4/15/2000	Common Test Methods for Cables Under Fire Conditions - Measurement of Smoke Density of Cables Burning Under Defined Conditions - Part 1: Apparatus-Supersedes BS 7622-1: 1993;
BSI	BS EN 50268-2	4/15/2000	Common Test Methods for Cables Under Fire Conditions - Measurement of Smoke Density of Cables Burning under Defined Conditions - Part 2: Procedure-Supersedes BS 7622-2: 1993;
BSI	BS EN 50274	7/23/2002	Low-Voltage Switchgear and Controlgear Assemblies - Protection Against Unintentional Direct Contact with Hazardous Live Parts
BSI	BS EN 50298	6/15/1999	Empty Enclosures for Low-Voltage Switchgear and Controlgear Assemblies - General Requirements-Superseded by BS EN 62208:2003
BSI	BS EN 50300	5/4/2004	Low-voltage switchgear and controlgear assemblies General requirements for low-voltage substation cable distribution boards
BSI	BS EN 50319	11/15/1999	Proximity Devices - Requirements for Proximity Devices with Analogue Output-Superseded by BS EN 60947-5-7:2003;
BSI	BS EN 50364	1/18/2002	Limitation of Human Exposure to Electromagnetic Fields from Devices Operating in the Frequency Range 0 Hz to 10 GHz, Used in Electronic Article Surveillance (EAS), Radio Frequency Identification (RFID) and Similar Applications
BSI	BS EN 50368	10/31/2003	Cable cleats for electrical installations
BSI	BS EN 50371	6/14/2002	Generic Standard to Demonstrate the Compliance of Low Power Electronic and Electrical Apparatus with the Basic Restrictions Related to Human Exposure to Electromagnetic Fields (10 MHz - 300 GHz) - General Public
BSI	BS EN 50392	2/18/2004	Generic standard to demonstrate the compliance of electronic and electrical apparatus with the basic restrictions related to human exposure to electromagnetic fields (0 Hz - 300 GHz)
BSI	BS EN 60061-1	5/15/1997	Lamp caps and holders together with gauges for the control of interchangeability and safety Part 1: Lamp caps-AMD 9694:November 1997; AMD 10186:February 1999; AMD 10583:December 1999; AMD 11008:July 2001; AMD 13245:March 27, 2002; AMD 14106:January 9, 2003; AMD 14568:November 28, 2003; AMD 14961:February 25, 2004; AMD 15488:February 10, 2005
BSI	BS EN 60061-2	5/15/1997	Lamp caps and holders together with gauges for the control of interchangeability and safety Part 2: Lampholders-AMD 9695: November 1997; AMD 10187: February 1999; AMD 10582: December 1999; AMD 11009: July 2001; AMD 13244: May 27, 2002; AMD 14108: January 13, 2003; AMD 14570: September 30, 2003; AMD 14836: January 12, 2004 and AMD 15486: April 15, 2005
BSI	BS EN 60061-3	5/15/1997	Lamp caps and holders together with gauges for the control of interchangeability and safety Part 3: Gauges-AMD 9696:November 1997; CORR 9999:April 1998; AMD 10188:February 1999; AMD 10579:December 1999; AMD 11010:July 2001; AMD 13243:September 16, 2002; AMD 14109:January 17, 2003; AMD 14571:September 24, 2003; AMD 14835:February 18, 2004; AMD 15487:January 17, 2005; AMD 15558:April 11, 2005
BSI	BS EN 60061-4	1/1/1992	Lamp Caps and Holders Together with Gauges for the Control of Interchangeability and Safety - Part 4: Guidelines and General Information-AMD 9308: August 1996; AMD 10189: March 1999; AMD 13137: September 2001; AMD 13589: September 17, 2002; AMD 14572: September 8,2003; AMD 15559: May 6, 2005
BSI	BS EN 60065	6/14/2002	Audio, video and similar electronic apparatus Safety requirements-CORR 14137: February 14, 2003
BSI	BS EN 60110-1	12/15/1998	Power Capacitors for Induction Heating Installations - Part 1: General-IEC 60110-1: 1998;
BSI	BS EN 60127-1	7/31/1991	Miniature fuses - Part 1: Definitions for miniature fuses and general requirements for minature fuse-links-AMD 14382: May 20, 2003
BSI	BS EN 60127-2	5/28/2003	Miniature fuses Part 2: Cartridge fuse-links-AMD 14903: January 14, 2004
BSI	BS EN 60127-3	11/15/1996	Miniature fuses Part 3: Specification for sub-miniature fuse-links-AMD 14530: September 3, 2003; IEC 60127-3: 1988 + A1: 1991
BSI	BS EN 60127-4	10/15/1998	Miniature fuses Part 4: Universal Modular Fuse-links (UMF)-AMD 14823: February 14, 2003
BSI	BS EN 60127-6	11/15/1994	Miniature fuses Part 6: Fuse-holders for miniature cartridge fuse-links-AMD 14513: August 20, 2003; IEC 60127-6: 1994
BSI	BS EN 60143-1	1/1/1993	Series Capacitors for Power Systems Part 1: General - Performance, Testing and Rating - Safety Requirements - Guide for Installation (AMD 8725) August 15, 1995 (Formerly BS EN 60143: 1993) (E)-Amd 1;
BSI	BS EN 60143-1	9/30/2005	Series Capacitors for Power Systems Part 1:
BSI	BS EN 60143-2	1/1/1995	Series Capacitors for Power Systems Part 2: Protective Equipment for Series Capacitor Banks (IEC 143-2: 1994) (E)
BSI	BS EN 60155	7/15/1995	Glow-Starters for Fluorescent Lamps-AMD 9126: September 1996; Supersedes BS 3772:1990; IEC 155: 1993
BSI	BS EN 60204-1	11/15/1998	Safety of Machinery - Electrical Equipment of Machines - Part 1: General Requirements-IEC 60204-1: 1997
BSI	BS EN 60215	9/28/1990	Safety Requirements for Radio Transmitting Equipment-AMD 9197: June 15, 1996; Renumbers BS 3192:1990; Also Known as BS 3192:1996
BSI	BS EN 60228	3/24/2005	Conductors of insulated cables
BSI	BS EN 60238	1/20/2005	Edison screw lampholders
BSI	BS EN 60252-1	1/1/2001	AC Motor Capacitors - Part 1: General - Performance, Testing and Rating - Safety Requirements - Guide for Installation and Operation-IEC 60252-1: 2001; Supersedes BS EN 60252:1994
BSI	BS EN 60252-2	10/29/2003	AC motor capacitors Part 2: Motor start capacitors
BSI	BS EN 60269-1	5/15/1999	Low-Voltage Fuses - Part 1: General Requirements-CORR 13161: August 31, 2001; IEC 60269-1: 1998
BSI	BS EN 60269-2	1/1/1995	Low-Voltage Fuses - Part 2: Supplementary Requirements for Fuses for Use by Authorized Persons (Fuses Mainly for Industrial Application)-AMD 13814: September 24, 2002; Renumbers BS 88-2.1: 1988; IEC 60269-2: 1986
BSI	BS EN 60269-3	9/15/1995	Low-voltage fuses Part 3: Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household and similar applications)-AMD 14901: February 23, 2004; Also Known as BS 88-3.1:1995; IEC 269-3:1987
BSI	BS EN 60269-4	1/1/1996	Low-voltage fuses Part 4: Supplementary requirements for fuse-links for the protection of semiconductor devices-AMD 14545: October 29, 2003; Renumbers BS 88-4:1988
BSI	BS EN 60269-4-1	7/9/2002	Low-Voltage Fuses - Part 4-1: Supplementary Requirements for Fuse-Links for the Protection of Semiconductor Devices - Sections I to III: Examples of Types of Standardized Fuse-Links
BSI	BS EN 60320-1	9/28/2001	Appliance Couplers for Household and Similar General Purposes Part 1: General Requirements
BSI	BS EN 60320-2-1	4/15/2001	Appliance Couplers for Household and Similar Purposes - Part 2-1: Sewing Machine Couplers-Supersedes BS 4491-2.1:1990; IEC 60320-2-1:2000;
BSI	BS EN 60320-2-2	1/15/1999	Appliance Couplers for Household and Similar General Purposes - Part 2-2: Interconnection Couplers for Household and Similar Equipment
BSI	BS EN 60332-1-1	1/18/2005	Tests on electric and optical fibre cables under fire conditions Part 1-1: Test for vertical flame propagation for a single insulated wire or cable Apparatus-Together with EN 60332-2-1:2004 Supersedes BS EN 50265-1:1999
BSI	BS EN 60332-1-2	12/10/2004	Tests on electric and optical fibre cables under fire conditions Part 1-2: Test for vertical flame propagation for a single insulated wire or cable Procedure for 1 kW pre-mixed flame-Supersedes BS EN 50265-2-1:1999
BSI	BS EN 60332-2-1	1/18/2005	Tests on electric and optical fibre cables under fire conditions Part 2-1: Test for vertical flame propagation for a single small insulated wire or cable Apparatus-Together with EN 60332-1-1:2004 Supersedes BS EN 50265-1:1999
BSI	BS EN 60332-2-2	12/9/2004	Tests on electric and optical fibre cables under fire conditions Part 2-2: Tests for vertical flame propagation for a single small insulated wire or cable Procedure for diffusion flame-Supersedes BS EN 50265-2-2:1999
BSI	BS EN 60360	4/15/1999	Standard Method of Measurement of Lamp Cap Temperature Rise-Supersedes BS 5371: 1990; IEC 60360: 1998
BSI	BS EN 60399	4/15/1994	Standard Sheets for Barrel Thread for E14 and E27 Lampholders with Shade Holder Ring-AMD 10578: March 2000
BSI	BS EN 60399	11/29/2004	Barrel thread for lampholders with shade holder ring
BSI	BS EN 60400	7/15/2000	Lampholders for tubular fluorescent lamps and starterholders-AMD 14037:February 17, 2003; CORR 14683: November 4, 2003; AMD 15463:November 29, 2004; IEC 60400:1999
BSI	BS EN 60432-1	7/15/2000	Incandescent Lamps - Safety Specifications - Part 1: Tungsten Filament Lamps for Domestic and Similar General Lighting Purposes
BSI	BS EN 60432-2	6/15/2000	Incandescent Lamps - Saftey Specification - Part 2: Tungsten Halogen Lamps for Domestic and Similar General Lighting Purposes
BSI	BS EN 60432-3	7/7/2003	Incandescent lamps Safety specifications Part 3: Tungsten-halogen lamps (non-vehicle)
BSI	BS EN 60439-1	12/15/1999	No. 1 Low-voltage switchgear and controlgear assemblies Part 1: Type-tested and partially type-tested assemblies-AMD 15206: June 30, 2004; CORR 15498: January 31, 2005
BSI	BS EN 60439-1	12/15/1999	Low-Voltage Switchgear and Controlgear Assemblies - Part 1: Type-Tested and Partially Type-Tested Assemblies-AMD 15206: June 30, 2004; IEC 60439-1: 1999
BSI	BS EN 60439-2	9/15/2000	Low-Voltage Switchgear and Controlgear Assemblies Part 2: Particular Requirements for Busbar Trunking Systems (Busways)-IEC 60439-2: 2000
BSI	BS EN 60439-3	6/28/1991	Low-Voltage Switchgear and Controlgear Assemblies - Part 3: Particular Requirements for Low-Voltage Switchgear and Controlgear Assemblies Intended to Be Installed in Places Where Unskilled Persons Have Access to Their Use - Distribution Boards-AMD 13466: May 1, 2002
BSI	BS EN 60439-4	1/11/2005	Low-voltage switchgear and controlgear assemblies Part 4: Particular requirements for assemblies for construction sites (ACS)
BSI	BS EN 60439-5	9/15/1996	Low-Voltage Switchgear and Controlgear Assemblies Part 5: Particular Requirements for Assemblies Intended to Be Installed Outdoors in Public Places - Cable Distribution Cabinets (CDCs) for Power Distribution in Networks-AMD 10498; March 2000; IEC 60439-5: 1996
BSI	BS EN 60446	3/15/2000	Basic and Safety Principles for Man-Machine Interface, Marking and Identification - Identification of Conductors by Colours or Numerals-IEC 60446: 1999
BSI	BS EN 60491	6/15/1997	Safety Requirements for Electronic Flash Apparatus for Photographic Purposes
BSI	BS EN 60529	1/31/1992	Degrees of Protection Provided by Enclosures (IP Code)-AMD 10931: August 2000
BSI	BS EN 60570	9/24/2003	Electrical supply track systems for luminaires
BSI	BS EN 60570-2-1	5/15/1995	AMD 1 Electrical Supply Track Systems for Luminaires Part 2: Mixed Supply Systems Section 1: Classes I and III-AMD 9384 February 15, 1997; IEC 570-2-1: 1994
BSI	BS EN 60598-1	11/16/2004	Luminaires Part 1: General requirements and tests
BSI	BS EN 60598-2-2	1/15/1997	Luminaires Part 2: Particular Requirements Section 2.2: Recessed Luminaires-AMD 9630: November 15, 1997; Supersedes BS 4533 SEC 102.2:1981; IEC 598-2-2: 1996
BSI	BS EN 60598-2-3	3/12/2003	Luminaires - Part 2-3: Particular requirements - Luminaires for road and street lighting
BSI	BS EN 60598-2-4	5/15/1998	Luminaires Part 2: Particular Requirements Section 2.4 Portable General Purpose Luminaires-Supersedes BS 4533: Part 102: Section 102.4: 1990
BSI	BS EN 60598-2-5	7/15/1998	Luminaires - Part 2-5: Particular Requirements - Floodlights-CORR 10560; December 1999; Supersedes BS 4533-102.5: 1990; IEC 60598-2-5: 1998
BSI	BS EN 60598-2-6	2/15/1995	Luminaires Part 2: Particular Requirements Section 2.6: Luminaires with Built-in Transformers for Filament Lamps-AMD 9553; September 1997; IEC 598-2-6: 1994
BSI	BS EN 60598-2-7	1/1/1997	Luminaires Part 2: Particular Requirements Section 7: Portable Luminaires for Garden Use-CORR 10563: December 1999; Supersedes BS 4533: Section 102.7: 1990
BSI	BS EN 60598-2-8	9/15/1997	And 1 Luminaires - Part 2: Particular Requirements - Section 8: Handlamps-AMD 12030:May 2001; Supersedes BS 4533-102.8:1990
BSI	BS EN 60598-2-10	10/31/2003	Luminaires Part 2-10: Particular requirements Portable luminaires for children
BSI	BS EN 60598-2-20	3/15/1998	Luminaires Part 2: Particular requirements Section 2.20 Lighting chains-AMD 10117:November 1998; CORR 10561:December 1999; AMD 15237:August 4, 2004; CORR 15417: October 27, 2004; CORR 15492:January 12, 2005
BSI	BS EN 60598-2-22	3/15/1999	Luminaires - Part 2-22: Particular Requirements - Luminaires for Emergency Lighting-AMD 14393: June 20,2003
BSI	BS EN 60598-2-23	1/15/1997	Luminaires - Part 2-23: Particular Requirements - Extra Low Voltage Lighting Systems for Filament Lamps-AMD 13045: June 2001; IEC 60598-2-23:1996
BSI	BS EN 60598-2-24	4/15/1999	Luminaires - Part 2: Particular Requirements - Section 24: Luminaires with Limited Surface Temperatures
BSI	BS EN 60598-2-25	1/1/1995	Luminaires Part 2: Particular Requirements Section 2.25: Luminaires for Use in Clinical Areas of Hospitals and Health Care Buildings (IEC 598-2-25: 1994)
BSI	BS EN 60645-1	11/19/2001	Electroacoustics - Audiological Equipment - Part 1: Pure-Tone Audiometers-IEC 60645-1:2001
BSI	BS EN 60645-3	1/1/1995	Audiometers Part 3: Auditory Test Signals of Short Duration for Audiometric and Neuro-Otological Purposes-IEC 645-3: 1994
BSI	BS EN 60645-4	1/1/1995	Audiometers Part 4: Equipment for Extended High-Frequency Audiometry-IEC 645-4: 1994
BSI	BS EN 60651	7/15/1994	Specification for Sound Level Meters-AMD 13114: October 15, 2001; Supersedes BS 5969: 1981; Superseded by 61672-2:2003 and BS EN 61672-2:2003
BSI	BS EN 60662	5/15/1993	High-Pressure Sodium Vapour Lamps-AMD 9934: April 1998; Supersedes BS 6193: 1990; Superseded by BS EN 62035: 2000
BSI	BS EN 60664-1	5/28/2003	Insulation coordination for equipment within low-voltage systems Part 1: Principles, requirements and tests-CORR 14806: October 21, 2003
BSI	BS EN 60664-3	6/9/2003	Insulation coordination for equipment within low-voltage systems Part 3: Use of coating, potting or moulding for protection against pollution
BSI	BS EN 60664-5	2/16/2004	Insulation coordination for equipment within low-voltage systems Part 5: A comprehensive method for determining clearances and creepage distances equal to or less than 2 mm
BSI	BS EN 60691	2/25/2003	Thermal-links - Requirements and application guide
BSI	BS EN 60695-1-1	8/15/2000	Fire Hazard Testing - Part 1-1: Guidance for Assessing the Fire Hazard of Electrotechnical Products - General Guidelines
BSI	BS EN 60695-2-2	9/15/1993	Fire Hazard Testing for Electrotechnical Products Part 2: Test Methods Section 2.2: Needle-Flame Test-AMD 9176: November 15, 1996; Superseded by BS EN 60695-11-5
BSI	BS EN 60695-2-4/0	1/1/1993	Fire Hazard Testing Part 2: Test Methods Section 2.4/0 Sheet 0: Diffusion Type and Premixed Type Flame Test Methods
BSI	BS EN 60695-2-4/1	1/1/1993	Fire Hazard Testing Part 2: Test Methods Section 2.4/1 Sheet 1: 1 kW Nominal Pre-Mixed Test Flame and Guidance-AMD 9264: November 15, 1996; Superseded by BS EN 60695-11-2:2003
BSI	BS EN 60695-2-10	6/15/2001	Fire Hazard Testing - Part 2-10: Glowing/Hot-Wire Based Test Methods - Glow-Wire Apparatus and Common Test Procedure-Supersedes BS EN 60695-2-1/0:1997
BSI	BS EN 60695-2-11	6/15/2001	Fire Hazard Testing - Part 2-11: Glowing/Hot-Wire Based Test Methods - Glow-Wire Flammability Test Method for End-Products-Supersedes BS EN 60695-2-1/1:1997
BSI	BS EN 60695-2-12	6/15/2001	Fire Hazard Testing - Part 2-12: Glowing/Hot-Wire Based Test Methods - Glow-Wire Flammability Test Method for Materials-Supersedes BS EN 60695-2-1/2:1996
BSI	BS EN 60695-2-13	6/15/2001	Fire Hazard Testing - Part 2-13: Glowing/Hot-Wire Based Tests Methods - Glow-Wire Ignitability Test Method for Materials-Supersedes BS EN 60695-2-1/3:1996
BSI	BS EN 60695-10-2	2/10/2004	Fire hazard testing Part 10-2: Abnormal heat Ball pressure test-:1995
BSI	BS EN 60695-10-3	9/11/2002	Fire Hazard Testing Part 10-3: Abnormal Heat Mould Stress Relief Distortion Test
BSI	BS EN 60695-11-2	2/18/2004	Fire hazard testing Part 11-2: Test flames 1 kW nominal pre-mixed flame Apparatus, confirmatory test arrangement and guidance-Supersedes BS EN 60695-2-4/1:1993
BSI	BS EN 60695-11-5	4/7/2005	Fire hazard testing Part 11-5: Test flames Needle-flame test method Apparatus, confirmatory test arrangement and guidance-Supersedes BS EN 60695-2-2:1995
BSI	BS EN 60695-11-10	11/15/1999	Fire hazard testing Part 11-10: Test flames 50 W horizontal and vertical flame test methods-AMD 14839: December 4, 2003
BSI	BS EN 60695-11-20	9/15/1999	Fire Hazard Testing - Part 11-20: Test Flames - 500 W Flame Test Methods-AMD 14840: December 5, 2003; Supersedes BS 2782-140C: 1993
BSI	BS EN 60702-1	4/10/2002	Mineral Insulated Cables and Their Terminations with a Rated voltage Not Exceeding 750 V - Part 1: Cables-Supersedes BS 6207-1:1995
BSI	BS EN 60702-2	4/10/2002	Mineral Insulated Cables and Their Terminations with a Rated Voltage Not Exceeding 750 V - Part 2: Terminations-Supersedes BS 6207-2:1995
BSI	BS EN 60715	8/15/2001	Dimensions of Low-Voltage Switchgear and Controlgear - Standardized Mounting on Rails for Mechanical Support of Electrical Devices in Switchgear and Controlgear Installations
BSI	BS EN 60719	11/15/1993	Calculation of the Lower and Upper Limits for the Average Outer Dimensions of Cables with Circular Copper Conductors and of Rated Voltages up to and Including 450/750 V-(IEC 719):1992
BSI	BS EN 60719	1/1/1993	Calculation of the Lower and Upper Limits for the Average Outer Dimensions of Cables with Circular Copper Conductors and of Rated Voltages up to and Including 450/750 V (IEC 719: 1992) (E)
BSI	BS EN 60799	12/15/1998	Electrical Accessories - Cord Sets and Interconnection Cord Sets-IEC 60799: 1998;
BSI	BS EN 60811-1-1	12/15/1995	Insulating and Sheathing Materials of Electric and Optical Cables - Common Test Methods - Part 1-1: General Application - Measurement of Thickness and Overall Dimensions - Tests for Determining the Mechanical Properties IEC 811-1-1: 1993) (F)-AMD 13461: May 27, 2002
BSI	BS EN 60811-1-2	12/15/1995	Common Test Methods for Insulating and Sheathing Materials of Electric Cables - Part 1-2: General Application - Thermal Ageing Methods-AMD 13462:April 12,2002; Supersedes BS 6469-1.2: 1992
BSI	BS EN 60811-1-3	12/15/1995	Insulating and Sheathing Materials of Electric Cables - Common Test Methods - Part 1-3: General Application - Methods for Determining the Density - Water Absorption Tests - Shrinkage Test-AMD 13463: May 27, 2002; Supersedes BS 6469: Part 1: Section 1.3: 1992
BSI	BS EN 60811-1-4	12/15/1995	Insulating and sheathing materials of electric cables - Common test methods - Part 1-4: General application - Tests at low temperature-CORR 14025: August 13, 2002; Supersedes BS 6469-1-4: 1992
BSI	BS EN 60811-2-1	11/15/1998	Insulating and sheathing materials of electric and optical cables Common test methods Part 2-1: Methods specific to elastomeric compounds Ozone resistance, hot set and mineral oil immersion tests-AMD 13624: August 28 2002
BSI	BS EN 60811-3-1	12/15/1995	Insulating and Sheathing Materials of Electric Cables - Common Test Methods - Part 3: Methods Specific to PVC Compounds - Section 3.1: Pressure Test at High Temperature - Tests for Resistance to Cracking-AMD 9407: April 1997; AMD 13464: May 27,2002;: 1992; IEC 811-3-1:1985
BSI	BS EN 60811-3-1	12/15/1995	Insulating and Sheathing Materials of Electric Cables - Common Test Methods - Part 3: Methods Specific to PVC Compounds - Section 3.1: Pressure Test at High Temperature - Tests for Resistance to Cracking-AMD 13464: May 27,2002; Supersedes BS 6469-3.1: 1992
BSI	BS EN 60811-3-2	12/15/1995	Insulating and sheathing materials of electric cables Common test methods Part 3: Methods specific to PVC compounds Section 2: Loss of mass test Thermal stability test-AMD 15142: May 12, 2004;:1992; IEC 811-3-2:1985
BSI	BS EN 60811-3-2	12/15/1995	Insulating and sheathing materials of electric cables Common test methods Part 3: Methods specific to PVC compounds Section 2: Loss of mass test Thermal stability test-AMD 15142: May 12, 2004; Supersedes BS 6469-3-2:1992
BSI	BS EN 60811-4-1	9/2/2004	Insulating and sheathing materials of electric and optical cables Common test methods Part 4-1: Methods specific to polyethylene and polypropylene compounds Resistance to environmental stress cracking Measurement of the melt flow index Carbon black and/or mineral filler content measurement in polyethylene by direct combustion Measurement of carbon black content by termogr
BSI	BS EN 60811-4-2	9/24/2004	Insulating and sheathing materials of electric and optical cables Common test methods Part 4-2: Methods specific to polyethylene and polypropylene compounds Tensile strength and elongation at break after conditioning at elevated temperature Wrapping test after conditioning at elevated temperature Wrapping test after thermal ageing in air Measurement of mass increase Long
BSI	BS EN 60811-5-1	6/15/2000	Insulating and sheathing materials of electric and optical fibre cables Common test methods Part 5-1: Methods specific to filling compounds Drop point Separation of oil Lower temperature brittleness Total acid number Absence of corrosive components Permittivity at 23 °C D.C resistivity at 23 °C and 100 °C-AMD 15143: April 28, 2004;:1992
BSI	BS EN 60825-1	12/15/1994	Safety of Laser Products - Part 1: Equipment Classification, Requirements and User´s Guide-AMD 9019: April 1996; AMD 9505: June 1997; AMD 13230: September 24, 2002; CORR 15182: May 20, 2004
BSI	BS EN 60825-2	11/12/2004	Safety of laser products Part 2: Safety of optical fibre communication systems (OFCS)
BSI	BS EN 60825-4	2/15/1998	Safety of laser products Part 4: Laser guards-AMD 14245: March 26, 2003; AMD 14844 January 29, 2004; IEC 60825-4: 1997;
BSI	BS EN 60825-12	5/19/2004	Safety of laser products Part 12: Safety of free space optical communication systems used for transmission of information
BSI	BS EN 60831-1	5/15/1998	Shunt power capacitors of the self-healing type for a.c. systems having a rated voltage up to and including 1kV Part 1: General Performance, testing and rating Safety requirements Guide for installation and operation-AMD 15017: March 10, 2004; IEC 60831-1: 1996
BSI	BS EN 60831-2	1/1/1996	Shunt Power Capacitors of the Self-Heating Type for a.c. Systems Having a Rated Voltage up to and Including 1 kV Part 2: Ageing Test, Self-Healing Test and Destruction Test-Supersedes BS 1650: 1971; IEC 831-2: 1995;
BSI	BS EN 60838-1	11/29/2004	Miscellaneous lampholders Part 1: General requirements and tests
BSI	BS EN 60838-2-1	3/15/1997	Miscellaneous Lampholders Part 2-1: Particular Requirements Section - Lampholders S14-AMD 10469: July 1999; AMD 15462: December 24, 2004; IEC 60838-2-1:1994
BSI	BS EN 60838-2-1	3/15/1997	Miscellaneous Lampholders Part 2: Particular Requirements Section 1: Lampholders S14-AMD 10469; July 1999; IEC 60838-2-1:1994
BSI	BS EN 60920	8/30/1991	Ballasts for Tubular Fluorescent Lamps - General and Safety Requirements-AMD 9151: September 15, 1996; AMD 13098 September 2001; Supersedes BS 2818: 1985
BSI	BS EN 60922	9/15/1997	Auxiliaries for Lamps - Ballasts for Discharge Lamps (Excluding Tubular Fluorescent Lamps) General and Safety Requirements
BSI	BS EN 60924	1/1/1991	General and Safety Requirements for D.C. Supplied Electronic Ballasts for Tubular Fluorescent Lamps (AMD 8297) October 15, 1994 (E)-Amd 1;
BSI	BS EN 60926	9/15/1996	Auxiliaries for Lamps - Starting Devices (Other Than Glow Starters) - General and Safety Requirements-Superseded by BS EN 61347-1:2001 and BS EN 61347-2-1:2001; AMD 10860 July 2000
BSI	BS EN 60928	12/15/1995	Auxiliaries for Lamps - A.C. Supplied Electronic Ballasts for Tubular Fluorescent Lamps - General and Safety Requirements-AMD 10732: March 2000
BSI	BS EN 60931-1	9/15/1998	Shunt Power Capacitors of the Non-Self-Healing Type for a.c. Systems Having a Rated Voltage up to and Including 1 kV - Part 1: General - Performance, Testing and Rating - Safety Requirements - Guide for Installation and Operation-AMD 15016: April 15,2004; IEC 60931-1:1996
BSI	BS EN 60931-2	1/1/1996	Shunt Power Capacitors of the Non-Self-Healing Type for a.c. Systems Having a Rated Voltage up to and Including 1 kV Part 2: Ageing Test and Destruction Test-Supersedes BS 1650: 1971; IEC 931-2: 1995;
BSI	BS EN 60931-3	9/15/1997	Shunt Power Capacitors of the Non-Self-Healing Type for a.c. Systems Having a Rated Voltage up to and Including 1 kV Part 3: Internal Fuses-Supersedes BS 1650: 1971; IEC 60931-3: 1996;
BSI	BS EN 60947-1	8/25/2004	Low-voltage switchgear and controlgear Part 1: General rules-CORR 15485: February 8, 2005
BSI	BS EN 60947-2	6/30/2003	Low-voltage switchgear and controlgear Part 2: Circuit-breakers
BSI	BS EN 60947-3	6/15/1999	Low-Voltage Switchgear and Controlgear - Part 3: Switches, Disconnectors, Switch-Disconnectors and Fuse-Combination Units-AMD 13240: April 05, 2002;
BSI	BS EN 60947-4-1	9/15/2001	Low-Voltage Switchgear and Controlgear - Part 4-1: Contactors and Motor-Starters - Electromechanical Contactors and Motor-Starters-AMD 14559; August 15, 2003; Supersedes BS EN 60947-4-1:1992;
BSI	BS EN 60947-4-2	1/1/2000	Low-voltage switchgear and controlgear Part 4-2: Contactors and motor-starters AC semiconductor motor controllers and starters-AMD 13852: October 11, 2002;
BSI	BS EN 60947-4-3	8/15/2000	Low-Voltage Switchgear and Controlgear - Part 4.3: Contactors and Motor-Starters - AC Semiconductor Controllers and Contactors for Non-Motor Loads-IEC 60947-4-3: 1999;
BSI	BS EN 60947-5-1	6/28/2004	Low-Voltage Switchgear and Controlgear - Part 5-1: Control Circuit Devices and Switching Elements - Electromechanical Control Circuit Devices-CORR 15484: January 31, 2005
BSI	BS EN 60947-5-1	6/28/2004	Low-Voltage Switchgear and Controlgear - Part 5-1: Control Circuit Devices and Switching Elements - Electromechanical Control Circuit Devices
BSI	BS EN 60947-5-2	1/15/1999	Low-Voltage Switchgear and Controlgear - Part 5-2: Control Circuit Devices and Switching Elements - Proximity Switches-AMD 10749: May 2000; AMD 15034: April 29, 2004
BSI	BS EN 60947-5-3	9/15/1999	Low-Voltage Switchgear and Controlgear - Part 5-3: Control Circuit Devices and Switching Elements - Requirements for Proximity Devices with Defined Behaviour under Fault Conditions (PDF)-IEC 60947-5-3: 1999;
BSI	BS EN 60947-5-4	12/18/2003	Low-voltage switchgear and controlgear Part 5-4: Control circuit devices and switching elements Method of assessing the performance of low-energy contacts Special tests
BSI	BS EN 60947-5-5	4/15/1998	Low-Voltage Switchgear and Controlgear Part 5-5: Control Circuit Devices and Switching Elements - Electrical Emergency Stop Devices with Mechanical Latching Function
BSI	BS EN 60947-5-7	10/16/2003	Low-voltage switchgear and controlgear Part 5-7: Control circuit devices and switching elements Requirements for proximity devices with analogue output-Supersedes BS EN 50319:1999;
BSI	BS EN 60947-6-1	4/1/1992	Low-Voltage Switchgear and Controlgear Part 6: Multiple Function Equipment Section 1: Automatic Transfer Switching Equipment-AMD 9941: April 1998;
BSI	BS EN 60947-6-2	6/26/2003	Low-voltage switchgear and controlgear Part 6-2: Multiple function equipment Control and protective switching devices (or equipment) (CPS)
BSI	BS EN 60947-7-1	11/28/2002	Low-voltage switchgear and controlgear Part 7-1: Ancillary equipment Terminal blocks for copper conductors-CORR 14468: July 7, 2003;
BSI	BS EN 60947-7-2	11/27/2002	Low-voltage switchgear and controlgear Part 7-2: Ancillary equipment Protective conductor terminal blocks for copper conductors
BSI	BS EN 60947-7-3	11/27/2002	Low-voltage switchgear and controlgear Part 7-3: Ancillary equipment Safety requirements for fuse terminal blocks-CORR 14469: July 16, 2003
BSI	BS EN 60947-8	8/1/2003	Low-voltage switchgear and controlgear Part 8: Control units for built-in thermal protection (PTC) for rotating electrical machines
BSI	BS EN 60950	8/15/2000	Safety of Information Technology Equipment-CORR 13834: July 8, 2002
BSI	BS EN 60950-1	2/22/2002	Information technology equipment Safety Part 1: General requirements-CORR 14424: July 10, 2003; AMD 15459: January 5, 2005
BSI	BS EN 60950-21	10/31/2003	Information technology equipment Safety Part 21: Remote power feeding
BSI	BS EN 60968	1/1/2000	Self-Ballasted Lamps for General Lighting Services - Safety Requirements-Renumbers BS 7173: 1989
BSI	BS EN 60998-1	6/5/2004	Connecting devices for low-voltage circuits for household and similar purposes Part 1: General requirements
BSI	BS EN 60998-2-1	6/10/2004	Connecting Devices for Low Voltage Circuits for Household and Similar Purposes - Part 2-1: Particular Requirements for Connecting Devices as Separate Entities with Screw-Type Clamping Units
BSI	BS EN 60998-2-2	6/7/2004	Connecting devices for low-voltage circuits for household and similar purposes Part 2-2: Particular requirements for connecting devices as separate entities with screwless-type clamping units
BSI	BS EN 60998-2-3	6/4/2004	Connecting Devices for Low-Voltage Circuits for Household and Similar Purposes - Part 2-3: Particular Requirements for Connecting Devices as Separate Entities with Insulation Piercing Clamping Units
BSI	BS EN 60998-2-4	1/1/1993	Connecting Devices for Low-Voltage Circuits for Household and Similar Purposes Part 2-4: Particular Requirements for Twist-on Connecting Devices
BSI	BS EN 60999-1	7/15/2000	Connecting Devices - Electrical Copper Conductors - Saftey Requirements for Screw-Type and Screwless-Type Clamping Units - Part 1:General Requirements and Particular Requirements for Clamping Units for Conductors from 0,2 mm2 up to 35 mm2 (Included)-Supersedes BS EN 60999:1993
BSI	BS EN 60999-2	8/12/2002	Connecting devices Electrical copper conductors Safety requirements for screw-type and screwless-type clamping units Part 2: Particular requirements for clamping units for conductors above 35 mm2 up to 300 mm2 (included)
BSI	BS EN 61010-1	6/15/2001	Safety requirements for electrical equipment for measurement, control, and laboratory use Part 1: General requirements-CORR 14512: September 19, 2003; IEC 61010-1: 2001;
BSI	BS EN 61010-2-010	12/11/2003	Safety requirements for electrical equipment for measurement, control, and laboratory use Part 2-010: Particular requirements for laboratory equipment for the heating of material
BSI	BS EN 61010-2-020	1/1/1995	Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use Part 2-020: Particular Requirements for Laboratory Centrifuges-IEC 1010-2-020: 1992; AMD 9301 March 1997; Supersedes BS 4402: 1982;
BSI	BS EN 61010-2-032	1/1/2002	Safety requirements for electrical equipment for measurement, control, and laboratory use Part 2-032: Particular requirements for hand-held and hand-manipulated current sensors for electrical test and measurement
BSI	BS EN 61010-2-041	3/15/1997	Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use Part 2-041: Particular Requirements for Autoclaves Using Steam for the Treatment of Medical Materials, and for Laboratory Processes-Partically Supersedes BS 2646 and BS 3970
BSI	BS EN 61010-2-042	7/15/1997	Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use Part 2-042: Particular Requirements for Autoclaves and Sterilizers Using Toxic Gas for the Treatment of Medical Materials, and for Laboratory Processes-IEC 61010-2-042: 1997;
BSI	BS EN 61010-2-043	1/15/1998	Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use Part 2-043: Particular Requirements for Dry Heat Sterilizers Using Either Hot Air or Hot Inert Gas for the Treatment of Medical Materials, and for Laboratory Processes-To Be Read in Conjunction with BS EN 61010-1: 1993; Supersedes Some Provisions of BS 3970: Part 1: 1990; IEC 61010-2-043: 1998;
BSI	BS EN 61010-2-045	7/15/2001	Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use - Part 2-045: Particular Requirements for Washer Disinfectors Used in Medical, Pharmaceutical, Veterinary and Laboratory Fields
BSI	BS EN 61010-2-051	12/12/2003	Safety requirements for electrical equipment for measurement, control, and laboratory use Part 2-051: Particular requirements for laboratory equipment for mixing and stirring-CORR 15004: February 2, 2004;
BSI	BS EN 61010-2-061	12/12/2003	Safety requirements for electrical equipment for measurement, control, and laboratory use Part 2-061: Particular requirements for laboratory atomic spectrometers with thermal atomization and ionization
BSI	BS EN 61010-2-081	7/18/2002	Safety requirements for electrical equipment for measurement, control and laboratory use Part 2-081: Particular requirements for automatic and semi-automatic laboratory equipment for analysis and other purposes-AMD 14902: January 14, 2004;
BSI	BS EN 61010-031	3/15/2002	Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use - Part 031: Safety Requirements for the Hand-Held Probe Assemblies for Electrical Measurement and Test-Supersedes BS EN 61010-2-031:1995; IEC 61010-031:2002
BSI	BS EN 61046	4/15/1995	D.C. or A.C. Supplied Electronic Step-Down Convertors for Filament Lamps - General and Safety Requirements-AMD 9152: November 15, 1996; Superseded by BS EN 61347-1:2001 and BS EN 61347-2-2:2001 but remains current
BSI	BS EN 61048	9/15/1993	Auxiliaries for Lamps - Capacitors for Use in Tubular Fluorescent and Other Discharge Lamp Circuits - General and Safety Requirements-AMD 10488; July 1999
BSI	BS EN 61050	9/12/1992	Transformers for Tubular Discharge Lamps Having a No-Load Output Voltage Exceeding 1000 V (Generally Called Neon- Transformers) General and Safety Requirements-AMD 9107: September 15, 1996
BSI	BS EN 61071-1	10/15/1997	Power Electronic Capacitors Part 1: General
BSI	BS EN 61071-2	1/1/1996	Power Electronic Capacitors Part 2: Requirements for Disconnecting Test on Fuses, Destruction Test, Self Healing Test and Endurance Test (IEC 1071-2: 1994) (S)
BSI	BS EN 61095	5/15/1993	Electromechanical Contactors for Household and Similar Purposes-AMD 7858: July 1993; AMD 10460: February 2000; AMD 13213: January 25, 2002; Supersedes BS 5424-3:1998
BSI	BS EN 61131-2	8/21/2003	Programmable controllers Part 2: Equipment requirements and tests-AMD 15180:June 24, 2004
BSI	BS EN 61138	9/15/1998	Cables for Portable Earthing and Short-Circuiting Equipment-AMD 14443: October 14, 2003
BSI	BS EN 61184	12/15/1997	Bayonet Lampholders-AMD 13193: September 11, 2001; AMD 15463: December 14, 2004
BSI	BS EN 61195	4/15/2000	Double-capped fluorescent lamps - Safety specifications-CORR 14352: April 15, 2003
BSI	BS EN 61199	4/15/2000	Single-Capped Fluorescent Lamps - Safety Specifications
BSI	BS EN 61204	8/15/1995	Low-Voltage Power Supply Devices, d.c. Output - Performance Characteristics-AMD 13278: June 28, 2002;
BSI	BS EN 61210	1/1/1995	Connecting Devices - Flat Quick-Connect Terminations for Electrical Copper Conductors - Safety Requirements
BSI	BS EN 61293	1/1/1995	Marking of Electrical Equipment with Ratings Related to Electrical Supply - Safety Requirements (IEC 1293: 1994) (E)
BSI	BS EN 61310-1	1/1/1995	Safety of Machinery - Indication, Marking and Actuation Part 1: Requirements for Visual, Auditory and Tactile Signals (F)
BSI	BS EN 61310-2	1/1/1995	Safety of Machinery - Indication, Marking and Actuation Part 2: Requirements for Marking
BSI	BS EN 61310-3	6/15/1999	Safety of Machinery - Indication, Marking and Actuation - Part 3: Requirements for the Location and Operation of Actuators-IEC 61310-3: 1999;
BSI	BS EN 61347-1	5/15/2001	Lamp Controlgear - Part 1: General and Safety Requirements-CORR 14667: September 26, 2003
BSI	BS EN 61347-2-1	5/15/2001	Lamp Controlgear - Part 2-1: Particular Requirements for Starting Devices (Other Than Glow Starters)-CORR 14668: September 26, 2003
BSI	BS EN 61347-2-2	5/15/2001	Lamp controlgear Part 2-2: Particular requirements for d.c. or a.c. supplied electronic step-down convertors for filament lamps-CORR 14670: September 26, 2003
BSI	BS EN 61347-2-3	5/15/2001	Lamp controlgear Part 2-3: Particular requirements for a.c. supplied electronic ballasts for fluorescent lamps-CORR 14669:September 26, 2003; AMD 15431:November 12, 2004
BSI	BS EN 61347-2-4	5/15/2001	Lamp Controlgear - Part 2-4: Particular Requirements for D.C. Supplied Electronic Ballasts for General Lighting-CORR 14666: September 26, 2003
BSI	BS EN 61347-2-7	5/15/2001	Lamp Controlgear - Part 2-7: Particular Requirements for D.C. Supplied Electronic Ballasts for Emergency Lighting-CORR 14663: September 26, 2003
BSI	BS EN 61347-2-8	5/15/2001	Lamp Controlgear - Part 2-8: Particular Requirements for Ballasts for Fluorescent Lamps-CORR 14662: September 26, 2003
BSI	BS EN 61347-2-9	5/15/2001	Lamp controlgear Part 2-9: Particular requirements for ballasts for discharge lamps (excluding fluorescent lamps)-CORR 14661: September 26, 2003; AMD 14979: February 10, 2004
BSI	BS EN 61347-2-10	5/15/2001	Lamp Controlgear - Part 2-10: Particular Requirements for Electronic Invertors and Convertors for High-Frequency Operation of Cold Tubular Discharge Lamps (Neon Tubes)
BSI	BS EN 61347-2-11	3/7/2002	Lamp controlgear Part 2-11: Particular requirements for miscellaneous electronic circuits used with luminaires
BSI	BS EN 61386-1	6/22/2004	Conduit systems for cable management Part 1: General requirements
BSI	BS EN 61386-21	5/19/2004	Conduit systems for cable management Part 21: Particular requirements Rigid conduit systems-Supersedes BS EN 50086-2-1:1996
BSI	BS EN 61386-23	5/26/2004	Conduit systems for cable management Part 23: Particular requirements Flexible conduit systems
BSI	BS EN 61537	3/14/2002	Cable Tray Systems and Cable Ladder Systems for Cable Management-IEC 61537:2001;
BSI	BS EN 61549	7/24/2003	Miscellaneous lamps
BSI	BS EN 61558-1	1/15/1998	Safety of power transformers, power supply units and similar Part 1: General requirements-Amd 10136: August 1998; AMD 14659: October 31, 2003; CORR 15086: May 24, 2004; Supersedes BS 3535 PART 2:1990
BSI	BS EN 61558-2-1	1/15/1998	Safety of Power Transformers, Power Supply Units and Similar Part 2.1: Particular Requirements for Separating Transformers for General Use-AMD 10138: August 15, 1998; IEC 61558-2-1: 1997;
BSI	BS EN 61558-2-2	4/15/1998	Safety of power transformers, power supply units and similar Part 2-2: Particular requirements for control transformers-AMD 10139:August 1998; CORR 1508