API API 1130 |
Computational Pipeline Monitoring for Liquid Pipelines-Second Edition |
API API 510 |
Pressure Vessel Inspection Code: Maintenance Inspection, Rating, Repair, and Alteration-Eighth Edition; Addendum 1 December 1998; Addendum 2 December 2000; Addendum 3 December 2001; Addendum 4 August 2003 |
API API 570 |
Piping Inspection Code Inspection, Repair, Alteration, and Rerating of In-Service Piping Systems-Second Edition; Addendum 1 - February 2000; Addendum 2 - December 2001; Addendum 3 - August 2003 |
API API/IP SPEC 1582 |
Specification for Similarity for API/IP 1581 Aviation Jet Fuel Filter/Separators |
API BULL 2U |
Bulletin on Stability Design of Cylindrical Shells-Third Edition |
API BULL 2V |
Design of Flat Plate Structures-Third Edition |
API BULL 5C2 |
Bulletin on Performance Properties of Casing, Tubing, and Drill Pipe- Twenty-First Edition |
API BULL 5C3 |
Bulletin on Formulas and Calculations for Casing, Tubing, Drill Pipe, and Line Pipe Properties-Sixth Edition; Supplment 1 - April 1999 |
API BULL D16 |
Suggested Procedure for Development of Spill Prevention Control and Countermeasure Plans-Third Edition |
API BULL D16 TEMPLATE |
Suggested Procedure for Development of Spill Prevention Control and Countermeasure Plans - Plan Template-Fourth Edition |
API MPMS 1 |
Manual of Petroleum Measurement Standards Chapter 1 - Vocabulary |
API MPMS 10.4 |
Manual of Petroleum Measurement Standards Chapter 10 - Sediment and Water Section 4 - Determination of Water and/or Sediment in Crude Oil by the Centrifuge Method (Field Procedure) |
API MPMS 11.2 |
Manual of Petroleum Measurement Standards Chapter 11.2.1 and 11.2.1M - Compressibility Factors for Hydrocarbons: 0-90 Degrees API Gravity and 638-1074 Kilograms per Cubic Metre Ranges Chapter 11.2.3 and 11.2.3M - Water Calibration of Provers Computer Tape |
API MPMS 11.4.1 |
Measurement StandardsChapter 11Physical PropertiesData Section 4Properties of Reference Materials Part 1Density of Water and Water Volumetric Correction Factors for Water Calibration of Volumetric Provers-First Edition |
API MPMS 12.1.1 |
Manual of Petroleum Measurement Standards Chapter 12 - Calculation of Petroleum Quantities Section 1 - Calculation of Static Petroleum Quantities Part 1 - Upright Cylindrical Tanks and Marine Vessels-Second Edition |
API MPMS 12.1.2 |
Manual of Petroleum Measurement Standards Chapter 12 - Calculation of Petroleum Quantities Section 1 - Calculation of Static Petroleum Quantities Part 2 - Calculation Procedures for Tank Cars-First Edition |
API MPMS 12.2 |
Manual of Petroleum Measurement Standards Chapter 12 - Calculation of Petroleum Quantities Section 2 - Calculation of Liquid Petroleum Quantities Measured by Turbine or Displacement Meters-First Edition |
API MPMS 12.2.1 |
Manual of Petroleum Measurement Standards Chapter 12 - Calculation of Petroleum Quantities Section 2 - Calculation of Petroleum Quantities Using Dynamic Measurement Methods and Volumetric Correction Factors Part 1 - Introduction- Second Edition |
API MPMS 12.2.2 |
Manual of Petroleum Measurement Standards Chapter 12 - Calculation of Petroleum Quantities Section 2 - Calculation of Petroleum Quantities Using Dynamic Measurement Methods and Volumetric Correction Factors Part 2 - Measurement Tickets-Third Edition |
API MPMS 14.3.1 |
Manual of Petroleum Measurement Standards Chapter 14 - Natural Gas Fluids Measurement Section 3 - Concentric, Square-Edged Orifice Meters Part 1 - General Equations and Uncertainty Guidelines-Third Edition; Errata - 1991; Errata - 1993; Replaces API MPMS |
API MPMS 14.3.3 |
Manual of Petroleum Measurement Standards Chapter 14 - Natural Gas Fluids Measurement Section 3 - Concentric, Square-Edged Orifice Meters Part 3 - Natural Gas Applications |
API MPMS 14.4 |
Manual of Petroleum Measurement Standards Chapter 14 - Natural Gas Fluids Measurement Section 4 - Converting Mass of Natural Gas Liquids and Vapors to Equivalent Liquid Volumes-First Edition |
API MPMS 14.5 |
Calculation of Gross Heating Value, Relative Density and Compressibility Factor for Natural Gas Mixtures from Compositional Analysis-GPA STD 2172- 96 |
API MPMS 14.8 |
Manual of Petroleum Measurement Standards Chapter 14 - Natural Gas Fluids Measurement Section 8 - Liquefied Petroleum Gas Measurement-Second Edition |
API MPMS 15 |
Manual of Petroleum Measurement Standards Chapter 15 - Guidelines for the Use of the International System of Units (SI) in the Petroleum and Allied Industries-API PUBL 2564 |
API MPMS 16.2 |
Manual of Petroleum Measurement Standards Chapter 16 - Measurement of Hydrocarbon Fluids by Weight or Mass Section 2 - Mass Measurement of Liquid Hydrocarbons in Vertical Cylindrical Storage Tanks by Hydrostatic Tank Gauging-First Edition |
API MPMS 2.2A |
Manual of Petroleum Measurement Standard Chapter 2 - Tank Calibration Section 2A - Measurement and Calibration of Upright Cylindrical Tanks by the Manual Tank Strapping Method-First Edition |
API MPMS 2.2B |
Manual of Petroleum Measurement Standards Chapter 2 - Tank Calibration Section 2B - Calibration of Upright Cylindrical Tanks Using the Optical Reference Line Method-First Edition |
API MPMS 2.2C |
Manual of Petroleum Measurement Standards Chapter 2 - Tank Calibration Section 2C - Calibration of Upright Cylindrical Tanks Using the Optical- Triangulation Method-First Edition/ ISO 7507-3 Adoption |
API MPMS 2.8A |
Manual of Petroleum Measurement Standards Chapter 2 - Tank Calibration Section 8A - Calibration of Tanks on Ships and Oceangoing Barges-First Edition |
API MPMS 20.1 |
Manual of Petroleum Measurement Standards Chapter 20 - Allocation Measurement Section 1 - Allocation Measurement |
API MPMS 21.1 |
Manual of Petroleum Measurement Standards Chapter 21 - Flow Measurement Using Electronic Metering Systems Section 1 - Electronic Gas Measurement |
API MPMS 3.1A |
Manual of Petroleum Measurement Standards Chapter 3 - Tank Gauging Section 1A - Standard Practice for the Manual Gauging of Petroleum and Petroleum Products-Second Edition |
API MPMS 3.1B |
Manual of Petroleum Measurement Standards Chapter 3 - Tank Gauging Section 1B - Standard Practice for Level Measurement of Liquid Hydrocarbons in Stationary Tanks by Automatic Tank Gauging-Second Edition |
API MPMS 4.1 |
Manual of Petroleum Measurement Standards Chapter 4 - Proving Systems Section 1 - Introduction-Third Edition |
API MPMS 4.2 |
Manual of Petroleum Measurement Standards Chapter 4 - Proving Systems Section 2 - Displacement Provers-Third Edition |
API MPMS 4.4 |
Manual of Petroleum Measurement Standards Chapter 4 - Proving Systems Section 4 - Tank Provers-Second Edition |
API MPMS 4.5 |
Manual of Petroleum Measurement Standards Chapter 4 - Proving Systems Section 5 - Master-Meter Provers-Second Edition; Supersedes 1101, 2531, 2533, 2534 |
API MPMS 4.8 |
Manual of Petroleum Measurement Standards Chapter 4 - Proving Systems Section 8 - Operation of Proving Systems |
API MPMS 5.1 |
Manual of Petroleum Measurement Standards Chapter 5 - Metering Section 1 - General Considerations for Measurement by Meters-Fourth Edition |
API MPMS 5.2 |
Manual of Petroleum Measurement Standards Chapter 5 - Metering Section 2 - Measurement of Liquid Hydrocarbons by Displacement Meters-Third Edition |
API MPMS 5.6 |
Metering, Section 6 - Measurment of Liquid Hydrocarbons by Coriolis Meters-First Edition; Replaces API H00004 and API H00006 |
API MPMS 5.8 |
Manual of Petroluem Measurement Standards Chapter 5 - Metering - Section 8 - Measurement of Liquid Hydrocarbons by Ultrasonic Flow Meters Using Transit Time Technology-First Edition |
API MPMS 6.1 |
Manual of Petroleum Measurement Standards Chapter 6 - Metering Assemblies Section 1 - Lease Automatic Custody Transfer (LACT) Systems-Second Edition |
API MPMS 7 |
Manual of Petroleum Measurement Standards Chapter 7 - Temperature Determination-First Edition; Supersedes Chapter 7, Section 1, 2, 3 and 4 |
API MPMS 8.2 |
Manual of Petroleum Measurement Standards Chapter 8 - Sampling Section 2 - Standard Practice for Automatic Sampling of Liquid Petroleum and Petroleum Products-Second Edition; ASTM D4177 |
API MPMS 8.4 |
Manual of Petroleum Measurement Standards Chapter 8 - Sampling Section 4 - Standard Practice for Sampling and Handling of Fuels for Volatility Measurement- Second Edition |
API MPMS 9.2 |
Manual of Petroleum Measurement Standards Chapter 9 - Determination Section 2 - Standard Test Method for Density or Relative Density of Light Hydrocarbons by Pressure Hydrometer-Second Edition |
API MPMS 9.3 |
Manual of Petroleum Measurement Standards Chapter 9 - Density Determination Section 3 - Standard Test Method for Density, Relative Density, and API Gravity of Crude Petroleum and Liquid Petroleum Products by Thermohydrometer Method-Second Edition |
API PUBL 1155 |
Evaluation Methodology for Software Based Leak Detection Systems- First Edition |
API PUBL 2026 |
Safe Access/Egress Involving Floating Roofs of Storage Tanks in Petroleum Service-Second Edition |
API PUBL 2030 |
Application of Water Spray Systems for Fire Protection in the Petroleum Industry-Second Edition |
API PUBL 2207 |
Preparing Tank Bottoms for Hot Work-Fifth Edition; Errata June 1999 |
API PUBL 2218 |
Fireproofing Practices in Petroleum and Petrochemical Processing Plants-Second Edition |
API PUBL 2510A |
Fire-Protection Considerations for the Design and Operation of Liquefied Petroleum Gas (LPG) Storage Facilities-Second Edition |
API PUBL 327 |
Aboveground Storage Tank Standards: A Tutorial |
API PUBL 4686 |
1999 Oil Spill Conference Proceedings |
API PUBL 4723 |
Refinery Stream Speciation |
API PUBL 534 |
Heat Recovery Steam Generators First Edition-First Edition |
API PUBL 581 |
Risk-Based Inspection Base Resource Document-First Edition |
API PUBL 850 |
API Standards 620, 650, and 653 Interpretations - Tank Construction and In-Service Inspection-Answers to Technical Inquiries; First Edition |
API PUBL 938 |
Experimental Study of Causes and Repair of Cracking of 1 1/4Cr- 1/2Mo Steel Equipment |
API PUBL 939- B |
Repair and Remediation Strategies for Equipment Operating in Wet H2S Service |
API REPORT 3 |
Oil Analysis in Production Discharges |
API RP 1102 |
Steel Pipelines Crossing Railroads and Highways |
API RP 1110 |
Pressure Testing of Liquid Petroleum Pipelines-Fourth Edition |
API RP 1111 |
Design, Construction, Operation, and Maintenance of Offshore Hydrocarbon Pipelines (Limit State Design)-Third Edition |
API RP 1117 |
Movement of In-Service Pipelines |
API RP 11AR |
Recommended Practice for Care and Use of Subsurface Pumps- Fourth Edition |
API RP 11BR |
Recommended Practice for Care and Handling of Sucker Rods- Eighth Edition; Supplement 1 10-1-1990; Supplement 2 7-1-1991 |
API RP 11PGT |
Recommended Practice for Packaged Combustion Gas Turbines |
API RP 11S2 |
Recommended Practice for Electric Submersible Pump Testing- Second Edition; Effective Date: 10/01/1997 |
API RP 11S2 RUSSIAN |
Recommended Practice for Electric Submersible Pump Testing- Second Edition; Effective Date: 10/01/1997 |
API RP 11S3 |
Recommended Practice for Electric Submersible Pump Installations- Second Edition |
API RP 11S4 |
Recommended Practice for Sizing and Selection of Electric Submersible Pump Installations-Third Edition |
API RP 12N |
Recommended Practice for the Operation, Maintenance and Testing of Firebox Flame Arrestors |
API RP 12R1 |
Recommended Practice for Setting, Maintenance, Inspection, Operation and Repair of Tanks in Production Service-Fifth Edition; Effective Date: 10/01/1997 |
API RP 13C |
Recommended Practice for Drilling Fluid Processing Systems Evaluation-Third Edition; Replaces API RP 13E; Errata: 04/2005 |
API RP 13D |
Recommended Practice on the Rheology and Hydraulics of Oil-Well Drilling Fluids-Fourth Edition |
API RP 14B |
Petroleum and natural gas industriesSubsurface safety valve systemsDesign, installation, operation and redress-Fifth Edition; ISO 10417 |
API RP 14C |
Recommended Practice for Analysis, Design, Installation, and Testing of Basic Surface Safety Systems for Offshore Production Platforms-Seventh Edition |
API RP 14E |
Recommended Practice for Design and Installation of Offshore Production Platform Piping Systems |
API RP 14F |
Recommended Practice for Design and Installation of Electrical Systems for Fixed and Floating Offshore Petroleum Facilities for Unclassified and Class I, Division 1 and Division 2 Locations-Fourth Edition |
API RP 14FZ |
Recommended Practice for Design and Installation of Electrical Systems for Fixed and Floating Offshore Petroleum Facilities for Unclassified and Class I, Zone 0, Zone 1 and Zone 2 Locations-First Edition |
API RP 14G |
Recommended Practice for Fire Prevention and Control on Open Type Offshore Production Platforms |
API RP 14H |
Recommended Practice for Installation, Maintenance and Repair of Surface Safety Valves and Underwater Safety Valves Offshore-Fourth Edition; ISO 10419; Errata - 1996 |
API RP 14J |
Recommended Practice for Design and Hazards Analysis for Offshore Production Facilities-Second Edition |
API RP 1615 |
Installation of Underground Petroleum Storage Systems |
API RP 1632 |
Cathodic Protection of Underground Petroleum Storage Tanks and Piping Systems |
API RP 16Q |
Recommended Practice for Design, Selection, Operation and Maintenance of Marine Drilling Riser Systems-First Edition; Formerly RP 2Q and RP 2K |
API RP 17A |
Design and Operation of Subsea Production Systems - General Requirements and Recommendations-Fourth Edition; ISO 13628-1:2005; ISO 13628-1 Adoption |
API RP 17B |
Recommended Practice for Flexible Pipe-Third Edition |
API RP 17C |
Recommended Practice on TFL (Through Flowline) Systems-Second Edition; ISO 13628-3/ISO 13628-3 Adoption |
API RP 2001 |
Fire Protection in Refineries-Eighth Edition |
API RP 2003 |
Protection Against Ignitions Arising out of Static, Lightning, and Stray Currents-Sixth Edition |
API RP 2009 |
Safe Welding, Cutting, and Other Hot Work Practices in the Petroleum and Petochemical Industries |
API RP 2016 |
Guidelines and Procedures for Entering and Cleaning Petroleum Storage Tanks-First Edition |
API RP 2021 |
Management of Atmospheric Storage Tank Fires-Fourth Edition |
API RP 2028 |
Flame Arresters in Piping Systems |
API RP 2200 |
Repairing Crude Oil, Liquefied Petroleum Gas, and Product Pipelines |
API RP 2201 |
Safe Hot Tapping Practices in the Petroleum & Petrochemical Industries-Fifth Edition |
API RP 2210 |
Flame Arresters for Vents of Tanks Storing Petroleum Products-Third Edition |
API RP 2221 |
Contractor and Owner Safety Program Implementation-Second Edition |
API RP 2350 |
Overfill Protection for Storage Tanks in Petroleum Facilities-Third Edition |
API RP 2556 |
Correcting Gauge Tables for Incrustation |
API RP 2A- LRFD |
Recommended Practice for Planning, Designing and Constructing Fixed Offshore Platforms - Load and Resistance Factor Design-First Edition; Errata - October 1993; Supplement 1 - February 1997 |
API RP 2A- WSD |
Recommended Practice for Planning, Designing and Constructing Fixed Offshore Platforms - Working Stress Design-Twenty-First Edition; Errata and Supplement 2: 10/2005 |
API RP 2D |
Operation and Maintenance of Offshore Cranes-Fifth Edition |
API RP 2FPS |
Recommended Practice for Planning, Designing, and Construction Floating Production Systems-First Edition |
API RP 2I |
In-Service Inspection of Mooring Hardware for Floating Drilling Units- Second Edition |
API RP 2L |
Recommended Practice for Planning, Designing, and Constructing Heliports for Fixed Offshore Platforms |
API RP 2N |
Recommended Practice for Planning, Designing, and Constructing Structures and Pipelines for Arctic Conditions |
API RP 2RD |
Design of Risers for Floating Production Systems (FPSs) and Tension-Leg Platforms (TLPs)-First Edition |
API RP 2SK |
Design and Analysis of Stationkeeping Systems for Floating Structures-Third Edition |
API RP 2T |
Recommended Practice for Planning, Designing, and Constructing Tension Leg Platforms-Second Edition |
API RP 2X |
Recommended Practice for Ultrasonic and Magnetic Examination of Offshore Structural Fabrication and Guidelines for Qualification of Technicians-Fourth Edition |
API RP 2Z |
Recommended Practice for Preproduction Qualification for Steel Plates for Offshore Structures-Fourth Edition |
API RP 44 |
Sampling Petroleum Reservoir Fluids-Second Edition |
API RP 45 |
Recommended Practice for Analysis of Oilfield Waters-Third Edition |
API RP 500 |
Recommended Practice for Classification of Locations for Electrical Installations at Petroleum Facilities Classified as Class I, Division 1 and Division 2-First Edition; Errata 10/17/1998 |
API RP 505 |
Recommended Practice for Classification of Locations for Electrical Installations at Petroleum Facilities Classified as Class I, Zone 0, Zone 1, and Zone 2-First Edition; Errata 8/17/98 |
API RP 520 PT I |
Sizing, Selection, and Installation of Pressure-Relieving Devices in Refineries; Part I - Sizing and Selection-Seventh Edition |
API RP 520 PT II |
Sizing, Selection, and Installation of Pressure-Relieving Devices in Refineries Part II - Installation-Fifth Edition |
API RP 521 |
Guide for Pressure-Relieving and Depressuring Systems-Fourth Edition; Errata February 15, 1999 |
API RP 54 |
Recommended Practice for Occupational Safety for Oil and Gas Well Drilling and Servicing Operations-Third Edition |
API RP 540 |
Electrical Installations in Petroleum Processing Plants-Fourth Edition |
API RP 55 |
Recommended Practices for Oil and Gas Producing and Gas Processing Plant Operations Involving Hydrogen Sulfide-Second Edition |
API RP 551 |
Process Measurement Instrumentation |
API RP 552 |
Transmission Systems-First Edition |
API RP 553 |
Refinery Control Valves-First Edition |
API RP 554 |
Process Instrumentation and Control-First Edition |
API RP 555 |
Process Analyzers-Second Edition |
API RP 556 |
Instrumentation and Control Systems for Fired Heaters and Steam Generators-First Edition |
API RP 557 |
Guide to Advanced Control Systems-First Edition |
API RP 571 |
Damage Mechanisms Affecting Fixed Equipment in the Refining Industry-First Edition |
API RP 572 |
Inspection of Pressure Vessels (Towers, Drums, Reactors, Heat Exchangers, and Condensers)-Second Edition |
API RP 573 |
Inspection of Fired Boilers and Heaters-Second Edition |
API RP 574 |
Inspection Practices for Piping System Components-Second Edition |
API RP 575 |
Guidelines and Methods for Inspection of Existing Atmospheric and Low-Pressure Storage Tanks-Second Edition |
API RP 576 |
Inspection of Pressure-Relieving Devices-Second Edition |
API RP 577 |
Welding Inspection and Metallurgy-First Edition |
API RP 578 |
Material Verification Program for New and Existing Alloy Piping Systems-First Edition |
API RP 579 |
Fitness-for-Service-First Edition; Errata March 2000 |
API RP 580 |
Risk-Based Inspection-First Edition |
API RP 582 |
Welding Guidelines for the Chemical, Oil, and Gas Industries-First Edition |
API RP 591 |
Process Valve Qualification Procedure-Third Edition |
API RP 5A3 |
Recommended Practice on Thread Compounds for Casing, Tubing, and Line Pipe-Second Edition/ISO 13678 Adoption |
API RP 5A5 |
Field Inspection of New Casing, Tubing, and Plain-End Drill Pipe- Seventh Edition; ISO 15463 Adoption |
API RP 5B1 |
Gauging and Inspection of Casing, Tubing, and Line Pipe Threads-Fifth Edition; Addendum 1: 09/2004 |
API RP 5C1 |
Recommended Practice for Care and Use of Casing and Tubing- Eighteenth Edition |
API RP 5C5 |
Recommended Practice on Procedures for Testing Casing and Tubing Connections-Third Edition/ISO 13679 Adoption |
API RP 5UE |
Recommended Practice for Ultrasonic Evaluation of Pipe Imperfections-Second Edition |
API RP 64 |
Recommended Practices for Diverter Systems Equipment and Operations-Second Edition |
API RP 651 |
Cathodic Protection of Aboveground Petroleum Storage Tanks-Second Edition |
API RP 652 |
Linings of Aboveground Petroleum Storage Tank Bottoms-Third Edition |
API RP 683 |
Quality Improvement Manual for Mechanical Equipment in Petroleum, Chemical, and Gas Industries |
API RP 684 |
Paragraphs Rotodynamic Tutorial: Lateral Critical Speeds, Unbalance Response, Stability, Train Torsionals and Rotor Balancing-Second Edition |
API RP 686 |
Recommended Practices for Machinery Installation and Installation Design-First Edition |
API RP 687 |
Rotor Repair-First Edition |
API RP 6HT |
Heat Treatment and Testing of Large Cross Section and Critical Section Components-First Edition |
API RP 75 |
Recommended Practices for Development of a Safety and Environmental Management Program for Offshore Operations and Facilities-Third Edition |
API RP 751 |
Safe Operation of Hydrofluoric Acid Alkylation Units-Second Edition |
API RP 752 |
Management of Hazards Associated with Location of Process Plant Buildings-Second Edition |
API RP 7C- 11F |
Recommended Practice for Installation, Maintenance, and Operation of Internal-Combustion Engines |
API RP 7G |
Recommended Practice for Drill Stem Design and Operating Limits- Sixteenth Edition; Errata May 2000; Addendum 1: November 2003 |
API RP 80 |
Guidelines for the Definition of Onshore Gas Gathering Lines-First Edition |
API RP 932- B |
Design, Materials, Fabrication, Operation, and Inspection Guidelines for Corrosion Control in Hydroprocessing Reactor Effluent Air Cooler (REAC) Systems-First Edition |
API RP 934 |
Materials and Fabrication Requirements for 2-1/4Cr-1Mo and 3Cr-1Mo Steel Heavy Wall Pressure Vessels for High Temperature, High Pressure Hyrdogen Service- First Edition |
API RP 936 |
Refractory Installation Quality Control Guidelines-Inspection and Testing Monolithic Refractory Linings and Materials-Second Edition |
API RP 941 |
Steels for Hydrogen Service at Elevated Temperatures and Pressures in Petroleum Refineries and Petrochemical Plants-Sixth Edition |
API RP 945 |
Avoiding Environmental Cracking in Amine Units-Third Edition |
API RP 9B |
Recommended Practice on Application Care, and Use of Wire Rope for Oil Field Service-Twelfth Edition |
API SPEC 10A |
Specification for Cements and Materials for Well Cementing-Twenty- Third Edition; ANSI/API 10A/ISO 10426-1-2001/ISO 10426-1 Adoption; Errata: January 2005 |
API SPEC 11D1 |
Petroleum and Natural Gas Industries - Downhole Equipment - Packers and Bridge Plugs-First Edition; ISO 14310:2001/ ISO 14310 Adoption |
API SPEC 11E |
Specification for Pumping Units |
API SPEC 12B |
Specification for Bolted Tanks for Storage of Production Liquids |
API SPEC 12D |
Specification for Field Welded Tanks for Storage of Production Liquids |
API SPEC 12F |
Specification for Shop Welded Tanks for Storage of Production Liquids |
API SPEC 12J |
Specification for Oil and Gas Separators |
API SPEC 12P |
Specification for Fiberglass Reinforced Plastic Tanks |
API SPEC 14A |
Petroleum and natural gas industriesDownhole equipmentSubsurface safety valve equipment-Eleventh Edition; ISO 10432 Adoption |
API SPEC 16A |
Specification for Drill-Through Equipment-Third Edition; ISO 13533:2001/ISO 13533 Adoption; Errata: 11/2004 |
API SPEC 16D |
Specification for Control Systems for Drilling Well Control Equipment and Control Systems for Diverter Equipment-Second Edition |
API SPEC 16F |
Specification for Marine Drilling Riser Equipment-First Edition |
API SPEC 16RCD |
Specification for Drill Through Equipment Rotating Control Devices-First Edition |
API SPEC 17E |
Specification for Subsea Umbilicals-Third Edition/ ISO 13628-5 Adoption |
API SPEC 17F |
Specification for Subsea Production Control Systems-First Edition; ISO 13628-6:2000/ISO 13628-6 Adoption |
API SPEC 17J |
Specification for Unbonded Flexible Pipe-Second Edition; Errata 5/25/2001; Addendum 1 06/2002 |
API SPEC 2B |
Specification for the Fabrication of Structural Steel Pipe-Sixth Edition |
API SPEC 2C |
Specification for Offshore Pedestal Mounted Cranes-Sixth Edition |
API SPEC 2H |
Specification for Carbon Manganese Steel Plate for Offshore Platform Tubular Joints-Eighth Edition; Effective Date: February 1, 2000 |
API SPEC 4F |
Specification for Drilling and Well Servicing Structures |
API SPEC 5B |
Specification for Threading, Gauging, and Thread Inspection of Casing, Tubing, and Line Pipe Threads (U.S. Customary Units)-Fourteenth Edition; Errata 4/9/1998; Addendum 1 3/2004 |
API SPEC 5CT |
Specification for Casing and Tubing-Eighth Edition; ISO 11960:2004 Adoption; Effective Date: January 1, 2006 |
API SPEC 5D |
Specification for Drill Pipe-Fifth Edition |
API SPEC 5L |
Specification for Line Pipe-Forty-Third Edition; Errata: 12/20/2004 |
API SPEC 5LC |
Specification for CRA Line Pipe-Third Edition |
API SPEC 5LD |
Specification for CRA Clad or Lined Steel Pipe-Second Edition |
API SPEC 6A |
Specification for Wellhead and Christmas Tree Equipment-Nineteenth Edition; ISO 10423 Adoption; Errata 1: 9/01/2004; Errata 2: 04/25/2005 |
API SPEC 6A718 |
Specification of Nickel Base Alloy 718 (UNS N07718) for Oil and Gas Drilling and Production Equipment-First Edition |
API SPEC 6D |
ISO 14313:1999, Petroleum and Natural Gas Industries-Pipeline Transportation Systems-Pipeline Valves-Twenty-Second Edition/ISO 14313 Adoption; Errata: 3/01/2005 |
API SPEC 6FA |
Specification for Fire Test for Valves-Third Edition |
API SPEC 8C |
Specification for Drilling and Production Hoisting Equipment (PSL 1 and PSL 2)-Fourth Edition; ISO 13535:2000/ ISO 13535 Adoption; Addendum 1: 11/1/2004; Addendum 2: 04/15/2005; |
API SPEC 9A |
Specification for Wire Rope-Twenty-fifth Edition; ANSI/API SPEC 9A/ISO 10425:2003/ISO 10425 Adoption |
API SPEC Q1 |
Specification for Quality Programs for the Petroleum, Petrochemical and Natural Gas Industry-Seventh Edition; Errata: August 2003/ISO TS29001 Adoption |
API STD 1104 |
Welding of Pipelines and Related Facilities-Twentieth Edition |
API STD 1160 |
Managing System Integrity for Hazardous Liquid Pipelines-First Edition |
API STD 1164 |
Pipeline SCADA Security-First Edition |
API STD 1631 |
Interior Lining and Periodic Inspection of Underground Storage Tanks- Fifth Edition; Supersedes RP 1631-1997 |
API STD 2000 |
Venting Atmospheric and Low-Pressure Storage Tanks Nonrefrigerated and Refrigerated-Fifth Edition; Errata 11/15/1999 |
API STD 2015 |
Requirements for Safe Entry and Cleaning of Petroleum Storage Tanks-Sixth Edition |
API STD 2217A |
Guidelines for Safe Work in Inert Confined Spaces in the Petroleum and Petrochemical Industries-Third Edition |
API STD 2220 |
Contractor Safety Performance Process-Second Edition |
API STD 2510 |
Design and Construction of LPG Installations-Eighth Edition |
API STD 2610 |
Design, Construction, Operation, Maintenance, and Inspection of Terminal & Tank Facilities-Second Edition |
API STD 526 |
Flanged Steel Pressure Relief Valves-Fifth Edition |
API STD 527 |
Seat Tightness of Pressure Relief Valves |
API STD 530 |
Calculation of Heater-Tube Thickness in Petroleum Refineries-Fifth Edition; ISO 13704:2001/ISO 13704 Adoption; Errata 1:3/01/04 |
API STD 537 |
Flare Details for General Refinery and Petrochemical Service-First Edition |
API STD 541 |
Form-Wound Squirrel-Cage Induction Motors - 500 Horsepower and Larger-Fourth Edition |
API STD 546 |
Brushless Synchronous Machines - 500 kVA and Larger-Second Edition |
API STD 547 |
General-purpose Form-wound Squirrel Cage Induction Motors 250 Horsepower and Larger-First Edition |
API STD 560 |
Fired Heaters for General Refinery Services-Third Edition; Errata: January 2002 |
API STD 594 |
Check Valves: Flanged, Lug, Wafer and Butt-welding-Sixth Edition |
API STD 598 |
Valve Inspection and Testing-Eighth Edition |
API STD 599 |
Metal Plug Valves - Flanged, Threaded and Welding Ends-Fifth Edition |
API STD 5T1 |
Standard on Imperfection Terminology-Tenth Edition; Formerly Bull 5T1; Addendum 1: 9/2003 |
API STD 600 |
Bolted Bonnet Steel Gate Valves for Petroleum and Natural Gas Industries-Eleventh Edition; ISO 10434:1998/ ISO 10434 Adoption |
API STD 602 |
Steel Gate, Globe and Check Valves for Sizes DN 100 and Smaller for the Petroleum and Natural Gas Industries-Eighth Edition; ISO 15761 Adoption |
API STD 603 |
Corrosion-Resistant, Bolted Bonnet Gate Valves - Flanged and Butt- Welding Ends-Sixth Edition |
API STD 607 |
Fire Test for Soft-Seated Quarter-Turn Valves-Fifth Edition; ISO 10497- 5:2004 Adoption |
API STD 608 |
Metal Ball Valves - Flanged, Threaded, and Welding End-Third Edition |
API STD 609 |
Butterfly Valves: Double Flanged, Lug- and Wafer-Type-Sixth Edition |
API STD 610 |
Centrifugal Pumps for Petroleum, Petrochemical and Natural Gas Industries-Tenth Edition; ISO 13709 Adoption |
API STD 611 |
General-Purpose Steam Turbines for Petroleum, Chemical, and Gas Industry Services-Fourth Edition |
API STD 612 |
Petroleum, Petrochemical and Natural Gas Industries - Steam Turbines - Special-Purpose Applications-Sixth Edition |
API STD 613 |
Special Purpose Gear Units for Petroleum, Chemical, and Gas Industry Services-Fifth Edition |
API STD 614 |
Lubrication, Shaft-Sealing, and Control-Oil Systems and Auxiliaries for Petroleum, Chemical and Gas Industry Services-Fourth Edition |
API STD 616 |
Gas Turbines for Petroleum, Chemical, and Gas Industry Services- Fourth Edition |
API STD 617 |
Axial and Centrifugal Compressors and Expander-Compressors for Petroleum, Chemical and Gas Industry Services-Seventh Edition; Errata: June 1, 2003 |
API STD 618 |
Reciprocating Compressors for Petroleum, Chemical, and Gas Industry Services |
API STD 619 |
Rotary-Type Positive-Displacement Compressors for Petroleum, Petrochemical, and Natural Gas Industries-Fourth Edition |
API STD 620 |
Design and Construction of Large, Welded, Low-Pressure Storage Tanks-Tenth Edition; Addendum 1: June 2004 |
API STD 650 |
Welded Steel Tanks for Oil Storage-Tenth Edition; Addendum 1, January 2000; Addendum 2, November 2001; Addendum 3, September 2003 |
API STD 653 |
Tank Inspection, Repair, Alteration, and Reconstruction-Third Edition; Addendum 1: 9/2003; Addendum 2: 11/2005 |
API STD 660 |
Shell-and-Tube Heat Exchangers for General Refinery Services- Seventh Edition/ ISO 16812 Adoption |
API STD 661 |
Air-Cooled Heat Exchangers for General Refinery Service-Fifth Edition; ISO 13706: 2000/ISO 13706 Adoption |
API STD 662 |
Plate Heat Exchangers for General Refinery Services-Second Edition; ISO 15547: 2000/ISO 15547 Adoption |
API STD 670 |
Machinery Protection Systems-Fourth Edition |
API STD 671 |
Special-Purpose Couplings for Petroleum, Chemical, and Gas Industry Services-Third Edition |
API STD 672 |
Packaged, Integrally Geared Centrifugal Air Compressors for Petroleum, Chemical, and Gas Industry Services-Fourth Edition |
API STD 673 |
Centrifugal Fans for Petroleum, Chemical and Gas for Industry Services-Second Edition; Errata: 10/2002 |
API STD 674 |
Positive Displacement Pumps - Reciprocating |
API STD 675 |
Positive Displacement Pumps - Controlled Volume |
API STD 676 |
Positive Displacement Pumps - Rotary-Errata; 06/15/1999 |
API STD 677 |
General Purpose Gear Units for Petroleum, Chemical, and Gas Industry Services-Second Edition |
API STD 681 |
Liquid Ring Vacuum Pumps and Compressors for Petroleum, Chemical, and Gas Industry Services-First Edition |
API STD 682 |
Pumps Shaft Sealing Systems for Centrifugal and Rotary Pumps-Third Edition; ISO 21049 Adoption |
API STD 685 |
Sealless Centrifugal Pumps for Petroleum, Heavy Duty Chemical, and Gas Industry Services Downstream Segment |
API TR 17TR1 |
Evaluation Standard for Internal Pressure Sheath Polymers for High Temperature Flexible Pipes-First Edition |
API TR 17TR2 |
The Ageing of PA-11 in Flexible Pipes-First Edition |
API TR 17TR3 |
An Evaluation of the Risks and Benefits of Penetrations in Subsea Wellheads below the BOP Stack |
API TR 2567 |
Evaporative Loss from Storage Tank Floating Roof Landings |
API TR 6AF |
Technical Report on Capabilities of API Flanges under Combinations of Load-Second Edition |
API TR 6AF2 |
Technical Report on Capabilities of API Integral Flanges under Combination of Loading - Phase II-Second Edition |
API TR 938- C |
Use of Duplex Stainless Steels in the Oil Refining Industry-First Edition |