|
ASTM D 3623 REV A |
Standard Test Method for Testing Antifouling Panels in Shallow Submergence |
|
ASTM D 3624 REV A |
Standard Test Method for Low Concentrations of Mercury in Paint by Atomic Absorption Spectroscopy |
|
ASTM D 365 |
Standard Guide for Soluble Nitrocellulose Base Solutions |
|
ASTM D 3717 REV A |
Standard Test Method for Low Concentrations of Antimony in Paint by Atomic Absorption Spectroscopy |
|
ASTM D 3718 REV A |
Standard Test Method for Low Concentrations of Chromium in Paint by Atomic Absorption Spectroscopy |
|
ASTM D 3719 |
Standard Test Method for Quantifying Dirt Collection on Coated Exterior Panels |
|
ASTM D 3720 |
Standard Test Method for Ratio of Anatase to Rutile in Titanium Dioxide Pigments by X-Ray Diffraction |
|
ASTM D 3721 |
Standard Specification for Synthetic Red Iron Oxide Pigment |
|
ASTM D 3722 |
Standard Specification for Natural Red and Brown Iron Oxide Pigments |
|
ASTM D 3723 |
Standard Test Method for Pigment Content of Water-Emulsion Paints by Low-Temperature Ashing |
|
ASTM D 3724 |
Standard Specification for Synthetic Brown Iron Oxide Pigment |
|
ASTM D 3725 |
Standard Test Method for Semiquantitative Determination of Fish Oil in Drying Oils and Drying Oil Fatty Acids by Gas-Liquid Chromatography |
|
ASTM D 3728 |
Standard Specification for 2-Ethoxyethyl Acetate (99% Grade) |
|
ASTM D 3730 |
Standard Guide for Testing High-Performance Interior Architectural Wall Coatings |
|
ASTM D 3732 |
Standard Practice for Reporting Cure Times of Ultraviolet-Cured Coatings |
|
ASTM D 3733 |
Standard Test Method for Silicon Content of Silicone Polymers and Silicon- Modified Alkyds by Atomic Absorption |
|
ASTM D 3734 |
Standard Specification for High-Flash Aromatic Naphthas |
|
ASTM D 3735 |
Standard Specification for VM&P Naphthas |
|
ASTM D 3760 |
Standard Test Method for Analysis of Isopropylbenzene (Cumene) by Gas Chromatography |
|
ASTM D 3792 |
Standard Test Method for Water Content of Coatings by Direct Injection Into a Gas Chromatograph |
|
ASTM D 3793 |
Standard Test Method for Low-Temperature Coalescence of Latex Paint Films |
|
ASTM D 3794 |
Standard Guide for Testing Coil Coatings |
|
ASTM D 3797 |
Standard Test Method for Analysis of o-Xylene by Gas Chromatography |
|
ASTM D 3798 |
Standard Test Method for Analysis of p-Xylene by Gas Chromatography |
|
ASTM D 3804 |
Standard Test Method for Iron in Paint Driers by EDTA Method |
|
ASTM D 3806 |
Standard Test Method of Small-Scale Evaluation of Fire-Retardant Paints (2- Foot Tunnel Method) |
|
ASTM D 3843 |
Standard Practice for Quality Assurance for Protective Coatings Applied to Nuclear Facilities |
|
ASTM D 3845 |
Standard Specification for Glacial Methacrylic Acid |
|
ASTM D 3852 |
Standard Practice for Sampling and Handling Phenol, Cresols, and Cresylic Acid |
|
ASTM D 387 |
Standard Test Method for Color and Strength of Chromatic Pigments with a Mechanical Muller |
|
ASTM D 3872 |
Standard Test Method for Ferrous Iron in Iron Oxides |
|
ASTM D 3876 |
Standard Test Method for Methoxyl and Hydroxypropyl Substitution in Cellulose Ether Products by Gas Chromatography |
|
ASTM D 3891 |
Standard Practice for Preparation of Glass Panels for Testing Paint, Varnish, Lacquer, and Related Products |
|
ASTM D 3893 |
Standard Test Method for Purity of Methyl Amyl Ketone and Methyl Isoamyl Ketone by Gas Chromatography |
|
ASTM D 3911 |
Standard Test Method for Evaluating Coatings Used in Light-Water Nuclear Power Plants at Simulated Design Basis Accident (DBA) Conditions |
|
ASTM D 3912 |
Standard Test Method for Chemical Resistance of Coatings Used in Light- Water Nuclear Power Plants |
|
ASTM D 3924 |
Standard Specification for Standard Environment for Conditioning and Testing Paint, Varnish, Lacquer, and Related Materials |
|
ASTM D 3925 |
Standard Practice for Sampling Liquid Paints and Related Pigmented Coatings |
|
ASTM D 3926 |
Standard Test Methods for Percent Solids in Titanium Dioxide Slurries |
|
ASTM D 3928 REV A |
Standard Test Method for Evaluation of Gloss or Sheen Uniformity |
|
ASTM D 3934 |
Standard Test Method for Flash/No Flash Test - Equilibrium Method by a Closed-Cup Apparatus |
|
ASTM D 3941 |
Standard Test Method for Flash Point by the Equilibrium Method With a Closed-Cup Apparatus |
|
ASTM D 3960 |
Standard Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings |
|
ASTM D 3964 |
Standard Practice for Selection of Coating Specimens for Appearance Measurements |
|
ASTM D 3969 |
Standard Test Method for Zirconium in Paint Driers by EDTA Method |
|
ASTM D 3970 |
Standard Test Method for Cerium in Paint Driers by Oxidimetric Determination |
|
ASTM D 3971 |
Standard Test Method for Dichloromethane-Soluble Matter in Cellulose |
|
ASTM D 3988 |
Standard Test Method for Vanadium in Paint Driers by EDTA Method |
|
ASTM D 3989 |
Standard Test Method for Total Rare Earth Metals in Paint Driers by EDTA Method |
|
ASTM D 4017 |
Standard Test Method for Water in Paints and Paint Materials by Karl Fischer Method |
|
ASTM D 4039 |
Standard Test Method for Reflection Haze of High-Gloss Surfaces |
|
ASTM D 4040 |
Standard Test Method for Rheological Properties of Paste Printing and Vehicles by the Falling-Rod Viscometer |
|
ASTM D 4060 |
Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser |
|
ASTM D 4062 |
Standard Test Method for Leveling of Paints by Draw-Down Method |
|
ASTM D 4077 |
Standard Specification for Cumene (Isopropylbenzene) |
|
ASTM D 4082 |
Standard Test Method for Effects of Gamma Radiation on Coatings for Use in Light-Water Nuclear Power Plants |
|
ASTM D 4085 |
Standard Test Method for Metals in Cellulose by Atomic Absorption Spectrophotometry |
|
ASTM D 4138 |
Standard Test Methods for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive Means |
|
ASTM D 4139 |
Standard Guide for Determining Volatile and Nonvolatile Content of Pigments |
|
ASTM D 4140 |
Standard Guide for Determining Volatile and Nonvolatile Content of Driers, Drying Oils, Naval Stores, and Solvents |
|
ASTM D 4141 |
Standard Practice for Conducting Black Box and Solar Concentrating Exposures of Coatings |
|
ASTM D 4142 |
Standard Guide for Testing Epoxy Resins |
|
ASTM D 4143 |
Standard Guide for Testing Latex Vehicles |
|
ASTM D 4144 |
Standard Test Method for Estimating Package Stability of Coatings for Ultraviolet Curing |
|
ASTM D 4145 |
Standard Test Method for Coating Flexibility of Prepainted Sheet |
|
ASTM D 4146 |
Standard Test Method for Formability of Zinc-Rich Primer/Chromate Complex Coatings on Steel |
|
ASTM D 4147 |
Standard Practice for Applying Coil Coatings Using the Wire-Wound Drawdown Bar |
|
ASTM D 4206 |
Standard Test Method for Sustained Burning of Liquid Mixtures Using the Small Scale Open-Cup Apparatus |
|
ASTM D 4209 |
Standard Practice for Determining Volatile and Nonvolatile Content of Cellulosics, Emulsions, Resin Solutions, Shellac, and Varnishes |
|
ASTM D 4212 |
Standard Test Method for Viscosity by Dip-Type Viscosity Cups |
|
ASTM D 4213 |
Standard Test Method for Scrub Resistance of Paints by Abrasion Weight Loss |
|
ASTM D 4214 |
Standard Test Methods for Evaluating the Degree of Chalking of Exterior Paint Films |
|
ASTM D 4217 |
Standard Test Method for Gel Time of Thermosetting Coating Powder |
|
ASTM D 4227 |
Standard Practice for Qualification of Coating Applicators for Application of Coatings to Concrete Surfaces |
|
ASTM D 4228 |
Standard Practice for Qualification of Coating Applicators for Application of Coatings to Steel Surfaces |
|
ASTM D 4236 |
Standard Practice for Labeling Art Materials for Chronic Health Hazards |
|
ASTM D 4242 |
Standard Test Method for Inclined Plate Flow for Thermosetting Coating Powders |
|
ASTM D 4258 |
Standard Practice for Surface Cleaning Concrete for Coating |
|
ASTM D 4259 |
Standard Practice for Abrading Concrete |
|
ASTM D 4260 |
Standard Practice for Liquid and Gelled Acid Etching of Concrete |
|
ASTM D 4261 |
Standard Practice for Surface Cleaning Concrete Masonry Units for Coating |
|
ASTM D 4262 |
Standard Test Method for pH of Chemically Cleaned or Etched Concrete Surfaces |
|
ASTM D 4263 |
Standard Test Method for Indicating Moisture in Concrete by the Plastic Sheet Method |
|
ASTM D 4277 |
Standard Guide for Testing Amino Resins |
|
ASTM D 4285 |
Standard Test Method for Indicating Oil or Water in Compressed Air |
|
ASTM D 4286 |
Standard Practice for Determining Coating Contractor Qualifications for Nuclear Powered Electric Generation Facilities |
|
ASTM D 4287 |
Standard Test Method for High-Shear Viscosity Using a Cone/Plate Viscometer |
|
ASTM D 4288 |
Standard Specification for Calcium Borosilicate Pigments |
|
ASTM D 4297 |
Standard Practice for Sampling and Handling Bisphenol A (4,4´- Isopropylidinediphenol) |
|
ASTM D 4301 |
Standard Test Method for Total Chlorine in Epoxy Resins and Compounds- Reinstated |
|
ASTM D 4302 |
Standard Specification for Artists´ Oil, Resin-Oil, and Alkyd Paints |
|
ASTM D 4303 |
Standard Test Methods for Lightfastness of Colorants Used in Artists Materials |
|
ASTM D 4358 |
Standard Test Method for Lead and Chromium in Air Particulate Filter Samples of Lead Chromate Type Pigment Dusts by Atomic Absorption Spectroscopy |
|
ASTM D 4359 |
Standard Test Method for Determining Whether a Material is a Liquid or a Solid |
|
ASTM D 4360 |
Standard Specification for Methyl n-Amyl Ketone |
|
ASTM D 4361 |
Standard Test Method for Apparent Tack of Printing Inks and Vehicles by a Three-Roller Tackmeter |
|
ASTM D 4367 |
Standard Test Method for Benzene in Hydrocarbon Solvents by Gas Chromatography |
|
ASTM D 4370 |
Standard Test Methods for Acid and Base Milliequivalent Content of Electrocoat Bath |
|
ASTM D 4399 |
Standard Test Method for Measuring Electrical Conductivity of Electrocoat Baths |
|
ASTM D 4400 |
Standard Test Method for Sag Resistance of Paints Using a Multinotch Applicator |
|
ASTM D 4414 |
Standard Practice for Measurement of Wet Film Thickness by Notch Gages |
|
ASTM D 4415 |
Standard Test Methods for Determination of Dimer in Acrylic Acid |
|
ASTM D 4416 |
Standard Specification for Acrylic Acid |
|
ASTM D 4417 |
Standard Test Methods for Field Measurement of Surface Profile of Blast Cleaned Steel |
|
ASTM D 444 |
Standard Test Methods for Chemical Analysis of Zinc Yellow Pigment (Zinc Chromate Yellow) |
|
ASTM D 4446 |
Standard Test Method for Anti-Swelling Effectiveness of Water-Repellent Formulations and Differential Swelling of Untreated Wood When Exposed to Liquid Water Environments |
|
ASTM D 4449 |
Standard Test Method for Visual Evaluation of Gloss Differences between Surfaces of Similar Appearance |
|
ASTM D 4450 |
Standard Test Method for Analysis of Zinc Hydroxy Phosphite Pigment |
|
ASTM D 4451 |
Standard Test Method for Pigment Content of Paints by Low-Temperature Ashing |
|
ASTM D 4457 |
Standard Test Method for Determination of Dichloromethane and 1,1,1- Trichloroethane in Paints and Coatings by Direct Injection into a Gas Chromatograph |
|
ASTM D 4462 |
Standard Specification for Zinc Hydroxy Phosphite Pigment |
|
ASTM D 4471 |
Standard Test Method for Pyridine Bases in Cresylic Acid by Direct Titration |
|
ASTM D 4487 |
Standard Test Methods for Analysis of Calcium Borosilicate |
|
ASTM D 4492 |
Standard Test Method for Analysis of Benzene by Gas Chromatography |
|
ASTM D 4493 |
Standard Test Method for Solidification Point of Bisphenol A (4,4´- Isopropylidenediphenol) |
|
ASTM D 4534 |
Standard Test Method for Benzene Content of Cyclic Products by Gas Chromatography |
|
ASTM D 4537 REV A |
Standard Guide for Establishing Procedures to Qualify and Certify Personnel Performing Coating Work Inspection in Nuclear Facilities |
|
ASTM D 4538 |
Standard Terminology Relating to Protective Coating and Lining Work for Power Generation Facilities |
|
ASTM D 4541 |
Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
|
ASTM D 4563 |
Standard Test Method for Determination by Atomic Absorption Spectroscopy of Titanium Dioxide Content of Pigments Recovered from Whole Paint |
|
ASTM D 4584 |
Standard Test Method for Measuring Apparent pH of Electrocoat Baths |
|
ASTM D 4585 |
Standard Practice for Testing Water Resistance of Coatings Using Controlled Condensation |
|
ASTM D 4587 |
Standard Practice for Fluorescent UV-Condensation Exposures of Paint and Related Coatings |
|
ASTM D 4590 |
Standard Test Method for Colorimetric Determination of p-tert-Butylcatechol in Styrene Monomer or AMS (Alpha-Methylstyrene) by Spectrophotometry |
|
ASTM D 4610 |
Standard Guide for Determining the Presence of and Removing Microbial (Fungal or Algal) Growth on Paint and Related Coatings |
|
ASTM D 4614 |
Standard Specification for Ethyl Acetate (All Grades) |
|
ASTM D 4615 |
Standard Specification for n-Butyl Acetate (All Grades) |
|
ASTM D 4618 |
Standard Specification for Design and Fabrication of Flue Gas Desulfurization System Components for Protective Lining Application |
|
ASTM D 4619 |
Standard Practice for Inspection of Linings in Operating Flue Gas Desulfurization Systems |
|
ASTM D 464 |
Standard Test Methods for Saponification Number of Naval Store Products Including Tall Oil and Other Related Products |
|
ASTM D 4640 |
Standard Test Method for Determining Stroke Cure Time of Thermosetting Phenol-Formaldehyde Resins |
|
ASTM D 465 |
Standard Test Methods for Acid Number of Naval Stores Products Including Tall Oil and Other Related Products |
|
ASTM D 4706 |
Standard Test Method for Qualitative Determination of Methylol Group in Phenolic Resins |
|
ASTM D 4707 |
Standard Test Method for Measuring Paint Spatter Resistance During Roller Application |
|
ASTM D 4708 |
Standard Practice for Preparation of Uniform Free Films of Organic Coatings |
|
ASTM D 4709 |
Standard Specification for Methyl Acrylate |
|
ASTM D 4710 |
Standard Specification for Acetaldehyde |
|
ASTM D 4712 REV A |
Standard Guide for Testing Industrial Water-Reducible Coatings |
|
ASTM D 4713 |
Standard Test Methods for Nonvolatile Content of Heatset and Liquid Printing Ink Systems |
|
ASTM D 4734 |
Standard Specification for Refined Benzene-545 |
|
ASTM D 4735 |
Standard Test Method for Determination of Trace Thiophene in Refined Benzene by Gas Chromatography |
|
ASTM D 4747 |
Standard Test Method for Determining Unreacted Monomer Content of Latexes Using Gas-Liquid Chromatography |
|
ASTM D 4752 |
Standard Test Method for Measuring MEK Resistance of Ethyl Silicate (Inorganic) Zinc-Rich Primers by Solvent Rub |
|
ASTM D 4758 |
Standard Test Method for Nonvolatile Content of Latexes |
|
ASTM D 476 |
Standard Classification for Dry Pigmentary Titanium Dioxide Products |
|
ASTM D 4764 |
Standard Test Method for Determination by X-Ray Fluorescence Spectroscopy of Titanium Dioxide Content in Paint |
|
ASTM D 4773 |
Standard Test Method for Purity of Propylene Glycol Monomethyl Ether, Dipropylene Glycol Monomethyl Ether, and Propylene Glycol Monomethyl Ether Acetate |
|
ASTM D 478 |
Standard Specification for Zinc Yellow (Zinc Chromate) Pigments |
|
ASTM D 4787 |
Standard Practice for Continuity Verification of Liquid or Sheet Linings Applied to Concrete Substrates |
|
ASTM D 4789 |
Standard Test Method for Solution Color of Bisphenol A (4,4´- Isopropylidenediphenol) |
|
ASTM D 4790 |
Standard Terminology of Aromatic Hydrocarbons and Related Chemicals |
|
ASTM D 4794 |
Standard Test Method for Determination of Ethoxyl or Hydroxyethoxyl Substitution in Cellulose Ether Products by Gas Chromatography |
|
ASTM D 4795 |
Standard Test Method for Nitrogen Content of Soluble Nitrocellulose - Alternative Method |
|
ASTM D 4796 |
Standard Test Method for Bond Strength of Thermoplastic Traffic Marking Materials |
|
ASTM D 4797 |
Standard Test Methods for Chemical and Gravimetric Analysis of White and Yellow Thermoplastic Traffic Marking Containing Lead Chromate and Titanium Dioxide |
|
ASTM D 480 |
Standard Test Methods for Sampling and Testing of Flaked Aluminum Powders and Pastes |
|
ASTM D 4827 |
Standard Test Method for Determining the Unreacted Monomer Content of Latexes Using Capillary Column Gas Chromatography |
|
ASTM D 4828 |
Standard Test Methods for Practical Washability of Organic Coatings |
|
ASTM D 4834 |
Standard Test Method for Detection of Lead in Paint by Direct Aspiration Atomic Absorption Spectroscopy |
|
ASTM D 4835 |
Standard Specification for Propylene Glycol Monomethyl Ether Acetate |
|
ASTM D 4836 |
Standard Specification for Dipropylene Glycol Monomethyl Ether |
|
ASTM D 4837 |
Standard Specification for Propylene Glycol Monomethyl Ether |
|
ASTM D 4838 |
Standard Test Method for Determining the Relative Tinting Strength of Chromatic Paints |
|
ASTM D 49 |
Standard Test Methods of Chemical Analysis of Red Lead |
|
ASTM D 4938 |
Standard Test Method for Erosion Testing of Antifouling Paints Using High Velocity Water |
|
ASTM D 4939 |
Standard Test Method for Subjecting Marine Antifouling Coating to Biofouling and Fluid Shear Forces in Natural Seawater |
|
ASTM D 4940 |
Standard Test Method for Conductimetric Analysis of Water Soluble Ionic Contamination of Blasting Abrasives |
|
ASTM D 4941 |
Standard Practice for Preparing Drawdowns of Artists´ Paste Paints |
|
ASTM D 4942 |
Standard Test Methods for Water Pickup of Lithographic Printing Inks and Vehicles in a Laboratory Mixer |
|
ASTM D 4946 |
Standard Test Method for Blocking Resistance of Architectural Paints |
|
ASTM D 4948 |
Standard Test Method for Determination of the Upper Layer Separated from a Viscous Liquid |
|
ASTM D 4958 |
Standard Test Method for Comparison of the Brush Drag of Latex Paints |
|
ASTM D 4960 |
Standard Test Method for Evaluation of Color for Thermoplastic Traffic Marking Materials |
|
ASTM D 50 |
Standard Test Methods for Chemical Analysis of Yellow, Orange, Red, and Brown Pigments Containing Iron and Manganese |
|
ASTM D 5007 |
Standard Test Method for Wet-To-Dry Hiding Change |
|
ASTM D 5008 |
Standard Test Method for Ethyl Methyl Pentanol Content and Purity Value of 2-Ethylhexanol by Gas Chromatography |
|
ASTM D 5009 |
Standard Test Method for Evaluating and Comparing Transfer Efficiency of Spray Applied Coatings Under Laboratory Conditions |
|
ASTM D 5010 |
Standard Guide for Testing Printing Inks and Related Materials |
|
ASTM D 5031 |
Standard Practice for Enclosed Carbon-Arc Exposure Tests of Paint and Related Coatings |
|
ASTM D 5043 |
Standard Test Methods for Field Identification of Coatings-Reinstated 2004 |
|
ASTM D 5060 |
Standard Test Method for Determining Impurities in High-Purity Ethylbenzene by Gas Chromatography |
|
ASTM D 5062 |
Standard Test Method for Resin Solution Dilutability by Volumetric/Gravimetric Determination |
|
ASTM D 5063 |
Standard Guide for Use of Certification of Coating Conformance Form |
|
ASTM D 5064 |
Standard Practice for Conducting a Patch Test to Assess Coating Compatibility |
|
ASTM D 5065 |
Standard Guide for Assessing the Condition of Aged Coatings on Steel Surfaces |
|
ASTM D 5066 |
Standard Test Method for Determination of the Transfer Efficiency Under Production Conditions for Spray Application of Automotive Paints - Weight Basis |
|
ASTM D 5067 |
Standard Specification for Artists´ Watercolor Paints |
|
ASTM D 5068 |
Standard Practice for Preparation of Paint Brushes for Evaluation |
|
ASTM D 5069 |
Standard Practice for Preparation of Paint-Roller Covers for Evaluation |
|
ASTM D 5087 |
Standard Test Method for Determining Amount of Volatile Organic Compound (VOC) Released from Solventborne Automotive Coatings and Available for Removal in a VOC Control Device (Abatement) |
|
ASTM D 509 |
Standard Test Methods of Sampling and Grading Rosin |
|
ASTM D 5095 |
Standard Test Method for Determination of the Nonvolatile Content in Silanes, Siloxanes and Silane-Siloxane Blends Used in Masonry Water Repellent Treatments |
|
ASTM D 5098 REV A |
Standard Specification for Artists Acrylic Dispersion Paints |
|
ASTM D 5107 |
Standard Practice for Preparatory Surface Cleaning of Architectural Sandstone |
|
ASTM D 5108 |
Standard Test Method for Organotin Release Rates of Antifouling Coating Systems in Sea Water |
|
ASTM D 5125 |
Standard Test Method for Viscosity of Paints and Related Materials by ISO Flow Cups |
|
ASTM D 5135 |
Standard Test Method for Analysis of Styrene by Capillary Gas Chromatography |
|
ASTM D 5136 |
Standard Specification for High Purity p-Xylene |
|
ASTM D 5137 |
Standard Specification for Hexyl Acetate |
|
ASTM D 5139 |
Standard Specification for Sample Preparation for Qualification Testing of Coatings to Be Used in Nuclear Power Plants |
|
ASTM D 5144 |
Standard Guide for Use of Protective Coating Standards in Nuclear Power Plants |
|
ASTM D 5145 |
Standard Test Methods for Nonvolatile and Pigment Content of Electrocoat Baths |
|
ASTM D 5146 |
Standard Guide to Testing Solvent-Borne Architectural Coatings |
|
ASTM D 5150 |
Standard Test Method for Hiding Power of Architectural Paints Applied by Roller |
|
ASTM D 5161 REV A |
Standard Guide for Specifying Inspection Requirements for Coating and Lining Work (Metal Substrates) |
|
ASTM D 5162 |
Standard Practice for Discontinuity (Holiday) Testing of Nonconductive Protective Coating on Metallic Substrates |
|
ASTM D 5163 REV A |
Standard Guide for Establishing Procedures to Monitor the Performance of Coating Service Level I Coating Systems in an Operating Nuclear Power Plant |
|
ASTM D 5164 |
Standard Specification for Propylene Glycol and Dipropylene Glycol |
|
ASTM D 5165 |
Standard Practice for Laboratory Preparation of Gelled Vehicles Using a Resin Kettle |
|
ASTM D 5166 |
Standard Practice for Laboratory Preparation of Gelled Vehicle Samples Using a Microwave Oven |
|
ASTM D 5178 |
Standard Test Method for Mar Resistance of Organic Coatings |
|
ASTM D 5179 |
Standard Test Method for Measuring Adhesion of Organic Coatings to Plastic Substrates by Direct Tensile Testing |
|
ASTM D 5180 |
Standard Test Method for Quantitative Test for Turbidity in Clear Liquids |
|
ASTM D 5181 |
Standard Test Method for Abrasion Resistance of Printed Matter by the GA- CAT Comprehensive Abrasion Tester |
|
ASTM D 5194 |
Standard Test Method for Trace Chloride in Liquid Aromatic Hydrocarbons |
|
ASTM D 520 |
Standard Specification for Zinc Dust Pigment |
|
ASTM D 5200 |
Standard Test Method for Determination of Weight Percent Volatile Content of Solvent-Borne Paints in Aerosol Cans |
|
ASTM D 5201 REV A |
Standard Practice for Calculating Formulation Physical Constants of Paints and Coatings |
|
ASTM D 521 |
Standard Test Methods for Chemical Analysis of Zinc Dust (Metallic Zinc Powder) |
|
ASTM D 5211 |
Standard Specification for Xylenes for p-Xylene Feedstock |
|
ASTM D 522 REV A |
Standard Test Methods for Mandrel Bend Test of Attached Organic Coatings |
|
ASTM D 523 |
Standard Test Method for Specular Gloss |
|
ASTM D 5286 |
Standard Test Methods for Determination of Transfer Efficiency Under General Production Conditions for Spray Application of Paints |
|
ASTM D 5301 |
Standard Practice for Physical Characterization of Paint Brushes |
|
ASTM D 5309 |
Standard Specification for Cyclohexane 999 |
|
ASTM D 5310 |
Standard Test Method for Tar Acid Composition by Capillary Gas Chromatography |
|
ASTM D 5324 |
Standard Guide for Testing Water-Borne Architectural Coatings |
|
ASTM D 5325 |
Standard Test Method for Determination of Weight Percent Volatile Content of Water- Borne Aerosol Paints |
|
ASTM D 5326 REV A |
Standard Test Method for Color Development in Tinted Latex Paints |
|
ASTM D 5327 |
Standard Practice for Evaluating and Comparing Transfer Efficiency of Spray Applied Coatings under General Laboratory Conditions |
|
ASTM D 5367 |
Standard Practice for Evaluating Coatings Applied over Surfaces Treated with Inhibitors Used to Prevent Flash Rusting of Steel When Water or Water/Abrasive Blasted |
|
ASTM D 5380 |
Standard Test Method for Identification of Crystalline Pigments and Extenders in Paint by X-Ray Diffraction Analysis |
|
ASTM D 5381 |
Standard Guide for X-Ray Fluorescence (XRF) Spectroscopy of Pigments and Extenders |
|
ASTM D 5382 |
Standard Guide to Evaluation of Optical Properties of Powder Coatings |
|
ASTM D 5383 |
Standard Practice for Visual Determination of the Lightfastness of Art Materials by Art Technologists |
|
ASTM D 5386 |
Standard Test Method for Color of Liquids Using Tristimulus Colorimetry |
|
ASTM D 5398 |
Standard Practice for Visual Evaluation of the Lightfastness of Art Materials by the User |
|
ASTM D 5399 |
Standard Test Method for Boiling Point Distribution of Hydrocarbon Solvents by Gas Chromatography |
|
ASTM D 5400 |
Standard Test Methods for Hydroxypropylcellulose |
|
ASTM D 5401 |
Standard Test Method for Evaluating Clear Water Repellent Coatings on Wood-Reinstate |
|
ASTM D 5402 |
Standard Practice for Assessing the Solvent Resistance of Organic Coatings Using Solvent Rubs |
|
ASTM D 5403 |
Standard Test Methods for Volatile Content of Radiation Curable Materials |
|
ASTM D 5471 |
Standard Specification for O-Xylene 980 |
|
ASTM D 5478 |
Standard Test Methods for Viscosity of Materials by a Falling Needle Viscometer |
|
ASTM D 5479 |
Standard Practice for Testing Biofouling Resistance of Marine Coatings Partially Immersed |
|
ASTM D 5498 |
Standard Guide for Developing a Training Program for Coating Work Inspectors in Nuclear Facilities |
|
ASTM D 5499 |
Standard Test Methods for Heat Resistance of Polymer Linings for Flue Gas Desulfurization Systems |
|
ASTM D 5517 |
Standard Test Method for Determining Extractability of Metals from Art Materials |
|
ASTM D 5531 |
Standard Guide for Preparation, Maintenance, and Distribution of Physical Product Standards for Color and Geometric Appearance of Coatings |
|
ASTM D 555 |
Standard Guide for Testing Drying Oils |
|
ASTM D 5588 |
Standard Test Method for Determination of the Microbial Condition of Paint, Paint Raw Materials, and Plant Areas |
|
ASTM D 5589 |
Standard Test Method for Determining the Resistance of Paint Films and Related Coatings to Algal Defacement |
|
ASTM D 5606 |
Standard Specification for Toluene for Toluene Diisocyanate (TDI) Feedstock |
|
ASTM D 561 |
Standard Specification for Carbon Black Pigment for Paint |
|
ASTM D 5618 |
Standard Test Method for Measurement of Barnacle Adhesion Strength in Shear |
|
ASTM D 562 |
Standard Test Method for Consistency of Paints Measuring Krebs Unit (KU) Viscosity Using a Stormer-Type Viscometer |
|
ASTM D 564 |
Standard Test Methods for Liquid Paint Driers |
|
ASTM D 5661 |
Standard Test Method for Relative Solvency of Petroleum Oils by the PKP Method |
|
ASTM D 5682 |
Standard Test Methods for Electrical Resistivity of Liquid Paint and Related Materials |
|
ASTM D 5702 |
Standard Practice for Field Sampling of Coating Films for Analysis for Heavy Metals |
|
ASTM D 5703 |
Standard Practice for Preparatory Surface Cleaning for Clay Brick Masonry |
|
ASTM D 5713 |
Standard Test Method for Analysis of High Purity Benzene for Cyclohexane Feedstock by Capillary Gas Chromatography |
|
ASTM D 5722 |
Standard Practice for Performing Accelerated Outdoor Weathering of Factory-Coated Embossed Hardboard Using Concentrated Natural Sunlight and a Soak-Freeze- Thaw Procedure |
|
ASTM D 5723 |
Standard Practice for Determination of Chromium Treatment Weight on Metal Substrates by X-Ray Fluorescence |
|
ASTM D 5724 |
Standard Specification for Gouache Paints |
|
ASTM D 5767 |
Standard Test Methods for Instrumental Measurement of Distinctness-Of- Image Gloss of Coating Surfaces |
|
ASTM D 5768 |
Standard Test Method for Determination of Iodine Value of Tall Oil Fatty Acids |
|
ASTM D 5776 |
Standard Test Method for Bromine Index of Aromatic Hydrocarbons by Electrometric Titration |
|
ASTM D 5794 |
Standard Guide for Determination of Anions in Cathodic Electrocoat Permeates by Ion Chromatography |
|
ASTM D 5795 |
Standard Test Method for Determination of Liquid Water Absorption of Coated Hardboard and Other Composite Wood Products Via "Cobb Ring" Apparatus |
|
ASTM D 5796 |
Standard Test Method for Measurement of Dry Film Thickness of Thin Film Coil-Coated Systems by Destructive Means Using a Boring Device |
|
ASTM D 5808 |
Standard Test Method for Determining Organic Chloride in Aromatic Hydrocarbons and Related Chemicals by Microcoulometry |
|
ASTM D 5860 |
Standard Test Method for Evaluation of the Effect of Water Repellent Treatments on Freeze-Thaw Resistance of Hydraulic Cement Mortar Specimens |
|
ASTM D 5861 |
Standard Guide for Significance of Particle Size Measurements of Coating Powders |
|
ASTM D 5871 |
Standard Specification for Benzene for Cyclohexane Feedstock |
|
ASTM D 5894 |
Standard Practice for Cyclic Salt Fog/UV Exposure of Painted Metal, (Alternating Exposures in a Fog/Dry Cabinet and a UV/Condensation Cabinet) |
|
ASTM D 5895 |
Standard Test Methods for Evaluating Drying or Curing During Film Formation of Organic Coatings Using Mechanical Recorders |
|
ASTM D 5896 |
Standard Test Method for Carbohydrate Distribution of Cellulosic Materials |
|
ASTM D 5897 |
Standard Test Method for Determination of Percent Hydroxyl on Cellulose Esters by Potentiometric Titration - Alternative Method |
|
ASTM D 5909 REV A |
Standard Test Method for Drying Time of Oxidative-Drying Printing Inks by Squalene Resistance |
|
ASTM D 5910 |
Standard Test Method for Determination of Free Formaldehyde in Emulsion Polymers by Liquid Chromatography-Reinstated |
|
ASTM D 5913 |
Standard Test Method for Evaluation of Cleanability of Paint Brushes |
|
ASTM D 5917 |
Standard Test Method for Trace Impurities in Monocyclic Aromatic Hydrocarbons by Gas Chromatography and External Calibration |
|
ASTM D 5958 |
Standard Practices for Preparation of Oil-Based Ink Resin Solutions |
|
ASTM D 5959 |
Standard Test Method for Bulk Density of Level Paintbrush Filaments |
|
ASTM D 5962 |
Standard Guide for Maintaining Unqualified Coatings (Paints) within Level I Areas of a Nuclear Power Facility |
|
ASTM D 5965 |
Standard Test Methods for Specific Gravity of Coating Powders |
|
ASTM D 600 |
Standard Specification for Liquid Paint Driers |
|
ASTM D 601 |
Standard Specification for Oiticica Oil (Permanently Liquid) |
|
ASTM D 602 |
Standard Specification for Barium Sulfate Pigments |
|
ASTM D 6037 |
Standard Test Methods for Dry Abrasion Mar Resistance of High Gloss Coatings |
|
ASTM D 6038 |
Standard Test Methods for Determining the Compatibility of Resin/Solvent Mixtures by Precipitation Temperature (Cloud Point) |
|
ASTM D 605 |
Standard Specification for Magnesium Silicate Pigment (Talc) |
|
ASTM D 6069 |
Standard Test Method for Trace Nitrogen in Aromatic Hydrocarbons by Oxidative Combustion and Reduced Pressure Chemiluminescence Detection |
|
ASTM D 607 |
Standard Specification for Wet Ground Mica Pigments |
|
ASTM D 6073 |
Standard Test Method for Relative Setting of Heatset Printing Inks by the Sinvatrol Tester |
|
ASTM D 608 |
Standard Specification for Dibutyl Phthalate |
|
ASTM D 609 |
Standard Practice for Preparation of Cold-Rolled Steel Panels for Testing Paint, Varnish, Conversion Coatings, and Related Coating Products |
|
ASTM D 6090 |
Standard Test Method for Softening Point Resins (Mettler Cup and Ball Method) |
|
ASTM D 6093 |
Standard Test Method for Percent Volume Nonvolatile Matter in Clear or Pigmented Coatings Using a Helium Gas Pycnometer |