|
ASTM D 3566 |
Standard Practice for RubberDetermination of Bromine in the Presence of Chlorine by Oxygen Combustion |
|
ASTM D 3832 |
Standard Specification for Rubber Seals Contacting Liquids in Solar Energy Systems |
|
ASTM D 3903 |
Standard Specification for Rubber Seals Used in Air-Heat Transport of Solar Energy Systems |
|
ASTM D 4005 |
Standard Test Method for Plastic-Coated Fabrics- Completeness of Fusion of PVC Dispersion Coatings |
|
ASTM D 4245 |
Standard Specification for Ozone-Resistant Thermoplastic Elastomer Insulation for Wire and Cable, 90 Degrees C Dry/75 Degrees C Wet Operation |
|
ASTM D 4573 |
Standard Test Method for Rubber ChemicalsDetermination of Oil Content in Oil-Treated Sulfur |
|
ASTM D 4732 |
Standard Specification for Cool-Application Filling Compounds for Telecommunications Wire and Cable |
|
ASTM D 6096 |
Standard Specification for Poly(Vinyl Chloride) Insulation for Wire and Cable, 90 Degrees C Operation |
|
ASTM D 6741 |
Standard Test Methods for Silanes Used in Rubber Formulations (bis-(triethoxysilylpropyl)sulfanes): Sulfur Content |
|
ASTM D 6852 |
Standard Guide for Determination of Biobased Content, Resources Consumption, and Environmental Profile of Materials and Products |
|
ASTM D 6909 |
Standard Specification for High Temperature and Acid-Resistant Fluorocarbon Terpolymer Elastomer |
|
ASTM D 7131 |
Standard Test Method for Determination of Ion Exchange Capacity (IEC) in Grafted Battery Separator |
|
ASTM F 1087 |
Standard Test Method for Linear Dimensional Stability of a Gasket Material to Moisture |
|
ASTM F 1845 |
Standard Test Method for Trace Metallic Impurities in Electronic Grade Aluminum-Copper, Aluminum-Silicon, and Aluminum-Copper-Silicon Alloys by High-Mass-Resolution Glow Discharge Mass Spectrometer |
|
ASTM F 2112 |
Standard Terminology for Membrane Switches |
|
ASTM F 418 |
Standard Practice for Preparation of Samples of the Constant Composition Region of Epitaxial Gallium Arsenide Phosphide for Hall Effect Measurements |
|
ASTM F 676 |
Standard Test Method for Measuring Unsaturated TTL Sink Current |
|
ASTM D 3156 |
Standard Practice for Rubber - Chromatographic Analysis of Antidegradants (Antioxidants, Antiozonants and Stabilizers) |
|
ASTM D 3902 |
Standard Test Method for Rubber Hose for Gas Diffusion of Liquefied Petroleum Gas |
|
ASTM D 4570 |
Standard Test Method for Rubber ChemicalsDetermination of Particle Size of Sulfur by Sieving (Dry) |
|
ASTM D 5406 |
Standard Practice for Rubber-Calculation of Producer's Process Performance Indexes |
|
ASTM D 5637 |
Standard Test Method for Moisture Resistance of Electrical Insulating Varnishes |
|
ASTM D 6739 |
Standard Test Method for Silica - pH Value |
|
ASTM D 748 |
Standard Specification for Natural Block Mica and Mica Films Suitable for Use in Fixed Mica-Dielectric Capacitors |
|
ASTM F 1 |
Standard Specification for Nickel-Clad and Nickel-Plated Steel Strip for Electron Tubes |
|
ASTM F 1502 |
Standard Test Method for Static Measurements on Tires for Passenger Cars, Light Trucks, and Medium Duty Vehicles |
|
ASTM F 18 |
Standard Specification and Test Method for Evaluation of Glass-To-Metal Headers Used in Electron Devices |
|
ASTM F 1843 |
Standard Practice for Sample Preparation of Transparent Plastic Films for Specular Gloss Measurements, on Membrane Switch Overlays |
|
ASTM F 1997 |
Standard Test Method for Determining the Sensitivity (Teasing) of a Tactile Membrane Switch |
|
ASTM D 1825 |
Standard Practice for Etching and Cleaning Copper-Clad Electrical Insulating Materials and Thermosetting Laminates for Electrical Testing |
|
ASTM D 1827 |
Standard Test Method for Gas Content (Nonacidic) of Insulating Liquids by Displacement with Carbon Dioxide |
|
ASTM D 3738 |
Standard Specification for Rubber-Coated Cloth Hospital Sheeting |
|
ASTM D 3848 |
Standard Test Methods for RubberEvaluation of NBR (Acrylonitrile-Butadiene Copolymers) Mixed With Carbon Black |
|
ASTM D 4934 |
Standard Test Method for Rubber Compounding Materials: 2-Benzothiazyl Sulfenamide AcceleratorsInsolubles |
|
ASTM D 5461 |
Standard Test Method for Rubber Compounding MaterialsWet Sieve Analysis of Powdered Rubber Compounding Materials |
|
ASTM F 1112 REV A |
Standard Test Method for Static Testing of Tubeless Pneumatic Tires for Rate of Loss of Inflation Pressure |
|
ASTM F 542 |
Standard Test Method for Exothermic Temperature of Encapsulating Compounds for Electronic and Microelectronic Encapsulation |
|
ASTM D 1807 |
Standard Test Methods for Refractive Index and Specific Optical Dispersion of Electrical Insulating Liquids |
|
ASTM D 3854 |
Standard Test Method for Rubber Thread - Resistance to Dry Heat |
|
ASTM D 4063 |
Standard Specification for Pressboard for Electrical Insulating Purposes |
|
ASTM D 4244 |
Standard Specification for General-Purpose, Heavy-Duty, and Extra-Heavy-Duty Acrylonitrile-Butadiene/Poly(Vinyl Chloride) (NBR/PVC) Jackets for Wire and Cable |
|
ASTM D 4314 |
Standard Specification for General-Purpose, Heavy-Duty, and Extra-Heavy-Duty Crosslinked Chlorosulfonated Polyethylene (CSM) Jackets for Wire and Cable |
|
ASTM D 4316 |
Standard Specification for Elastomeric Water Bottles |
|
ASTM D 6600 |
Standard Practice for Evaluating Test Sensitivity for Rubber Test Methods |
|
ASTM F 180 |
Standard Test Method for Density of Fine Wire and Ribbon Wire for Electronic Devices |
|
ASTM F 256 |
Standard Specification for Chromium-Iron Sealing Alloys with 18 or 28 Percent Chromium |
|
ASTM F 364 |
Standard Specification for Molybdenum Flattened Wire for Electron Tubes |
|
ASTM F 508 |
Standard Practice for Specifying Thick-Film Pastes |
|
ASTM F 677 |
Standard Test Method for Fluid and Grease Resistance of Thermoset Encapsulating Compounds Used in Electronic and Microelectronic Applications |
|
ASTM F 980M |
Standard Guide for the Measurement of Rapid Annealing of Neutron-Induced Displacement Damage in Silicon Semiconductor Devices (Metric) |
|
ASTM D 1934 |
Standard Test Method for Oxidative Aging of Electrical Insulating Petroleum Oils by Open-Beaker Method |
|
ASTM D 5638 |
Standard Test Method for Chemical Resistance of Electrical Insulating Varnishes |
|
ASTM D 5817 REV A |
Standard Practice for Carbon Black, PelletedReduction, Blending, and Drying of Gross Samples for Testing |
|
ASTM D 7198 |
Standard Specification for Disposable Embalming Gloves for Single-Use Applications |
|
ASTM D 7246 |
Standard Test Method for Detection of Holes in Polyethylene Food Service Gloves |
|
ASTM F 1426 |
Standard Practice for Identifying Tire Tread Surface Irregular Wear Patterns Resulting from Tire Use |
|
ASTM F 1570 |
Standard Test Method for Determining the Tactile Ratio of a Membrane Switch |
|
ASTM F 1762 |
Standard Practice for Exposing a Membrane Switch to Variation in Atmospheric Pressure |
|
ASTM F 2405 |
Standard Test Method for Trace Metallic Impurities in High Purity Copper by High-Mass-Resolution Glow Discharge Mass Spectrometer |
|
ASTM D 3312 |
Standard Test Method for Percent Reactive Monomer in Solventless Varnishes |
|
ASTM D 4572 |
Standard Test Method for Rubber ChemicalsWet Sieve Analysis of Sulfur |
|
ASTM D 6070 |
Standard Test Methods for Physical Properties of Smooth-Wall, Coilable, Polyethylene (PE) Conduit (Duct) for Preassembled Wire and Cable |
|
ASTM D 6740 |
Standard Test Method for Silanes Used in Rubber Formulations (Bis-(Triethoxysilylpropyl)Sulfanes): Residue on Ignition |
|
ASTM D 784 |
Standard Specification for Orange Shellac and Other Indian Lacs for Electrical Insulation |
|
ASTM F 1211 |
Standard Specification for Semiconductor Device Passivation Opening Layouts |
|
ASTM F 1212 |
Standard Test Method for Thermal Stability Testing of Gallium Arsenide Wafers |
|
ASTM F 1661 |
Standard Test Method for Determining the Contact Bounce Time of a Membrane Switch |
|
ASTM F 1663 |
Standard Test Method for Determining the Capacitance of a Membrane Switch |
|
ASTM F 2086 |
Standard Test Method for Pass Through Flux of Circular Magnetic Sputtering Targets, Method 2 |
|
ASTM F 2359 |
Standard Test Method for Determining Color of a Membrane Switch Backlit with Diffuse Light Source |
|
ASTM D 6086 |
Standard Test Method for Carbon BlackVoid Volume (VV) |
|
ASTM F 1035 |
Standard Practice for Use of Rubber-Cord Pie Disk to Demonstrate the Discernment Capability of a Tire X-Ray Imaging System |
|
ASTM F 111 |
Standard Practice for Determining Barium Yield, Getter Gas Content, and Getter Sorption Capacity for Barium Flash Getters |
|
ASTM F 1404 |
Test Method for Crystallographic Perfection of Gallium Arsenide by Molten Potassium Hydroxide (KOH) Etch Technique |
|
ASTM F 551 |
Standard Practice for Using a 67.23-in. (1.707-m) Diameter Laboratory Test Roadwheel in Testing Tires |
|
ASTM D 3555 |
Standard Specification for Track-Resistant Black Crosslinked Polyethylene Insulation for Wire and Cable, 90 Degrees C Operation |
|
ASTM D 4295 |
Standard Classification for Rubber Compounding MaterialsZinc Oxide |
|
ASTM D 4528 |
Standard Classification for Rubber Compounding MaterialsSulfur |
|
ASTM D 4676 |
Standard Classification for Rubber Compounding Materials - Antidegradents |
|
ASTM D 4733 |
Standard Test Methods for Solventless Electrical Insulating Varnishes |
|
ASTM D 5899 |
Standard Classification System for Rubber Compounding Materials for Use in Computer Material Management Systems |
|
ASTM D 7160 |
Standard Practice for Determination of Expiration Dating for Medical Gloves |
|
ASTM F 1682 |
Standard Test Method for Determining Travel of a Membrane Switch |
|
ASTM F 1909 |
Standard Specification for Preformed Open-Cell Sponge Rubber Pail and Drum Gaskets |
|
ASTM F 2358 |
Standard Guide for Measuring Characteristics of Sapphire Substrates |
|
ASTM F 269 |
Standard Test Method for Sag of Tungsten Wire |
|
ASTM D 4559 |
Standard Test Method for Volatile Matter in Silicone Fluid |
|
ASTM D 5775 |
Standard Test Method for Rubber - Determination of Bound Styrene in Styrene Butadiene Rubber by Refractive Index |
|
ASTM D 7161 |
Standard Practice for Determination of Real Time Expiration Dating of Mature Medical Gloves Stored Under Typical Warehouse Conditions |
|
ASTM F 85 |
Standard Practice for Nomenclature for Wire Leads Used as Conductors in Electron Tubes |
|
ASTM D 3771 |
Standard Specification for Rubber Seals Used in Concentrating Solar Collectors |
|
ASTM D 3855 |
Standard Test Method for Rubber Thread - Deterioration Due to Standard Washing Solution Treatment |
|
ASTM D 4880 |
Standard Test Method for Salt Water Proofness of Insulating Varnishes over Enamelled Magnet Wire |
|
ASTM D 4937 |
Standard Test Method for p-Phenylenediamine Antidegradants Purity by Gas Chromatography |
|
ASTM D 5193/D 5193M |
Standard Test Method for Coated Fabrics-Air Retention |
|
ASTM D 5666 |
Standard Test Method for Rubber Chemical AntidegradantsPurity of p-Phenylenediamine (PPD) Antidegradants by High Performance Liquid Chromatography |
|
ASTM D 7102 |
Standard Guide for Determination of Endotoxin on Sterile Medical Gloves |
|
ASTM D 3847 |
Standard Practice for Rubber - Directions for Achieving Subnormal Test Temperatures |
|
ASTM D 4817 |
Standard Classification for Rubber Compounding MaterialsStearic Acid |
|
ASTM D 5377 |
Standard Classification for Rubber Compounding Materials-Ground Coal |
|
ASTM F 2360 |
Standard Test Method for Determining Luminance of a Membrane Switch Backlit with Diffuse Light Source |
|
ASTM D 4363 |
Standard Specification for Thermoplastic Chlorinated Polyethylene (CM) Jacket for Wire and Cable |
|
ASTM D 5099 |
Standard Test Methods for Rubber - Measurement of Processing Properties Using Capillary Rheometry |
|
ASTM D 6844 |
Standard Test Method for Silanes Used in Rubber Formulations (bis-(triethoxysilylpropyl)sulfanes): Characterization by High Performance Liquid Chromatography (HPLC) |
|
ASTM D 6976 |
Standard Specification for Rubber ContraceptivesVaginal Diaphragms |
|
ASTM F 2113 |
Standard Guide for Analysis and Reporting the Impurity Content and Grade of High Purity Metallic Sputtering Targets for Electronic Thin Film Applications |
|
ASTM F 811 |
Standard Practice for Accelerometer Use in Vehicles for Tire Testing |
|
ASTM F 83 |
Standard Practice for Definition and Determination of Thermionic Constants of Electron Emitters |
|
ASTM D 4620 |
Standard Test Method for Evaluating the Effective Surface Area of Zinc Oxide in Rubber |
|
ASTM D 6845 |
Standard Test Methods for Silica, Precipitated, Hydrated-CTAB (Cetyltrimethylammonium Bromide) Surface Area |
|
ASTM D 4677 |
Standard Classification for Rubber Compounding MaterialsTitanium Dioxide |
|
ASTM D 4882 |
Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Twisted-Coil Test |
|
ASTM D 4924 |
Standard Classification for Petroleum Waxes for Use in Rubber Compounding |
|
ASTM D 4818 |
Standard Classification for Rubber Compounding MaterialsVulcanization Accelerators |
|
ASTM D 5603 |
Standard Classification for Rubber Compounding Materials - Recycled Vulcanizate Particulate Rubber |
|
ASTM D 6515 |
Standard Test Method for Rubber Shaft Seals Determination of Recovery from Bending |
|
ASTM D 5054 |
Standard Test Method for Rubber Chemicals - Diphenyl Guanidine (DPG) and Di-o-tolyl-guanidine (DOTG) Assay |
|
ASTM D 6843 |
Standard Test Method for Silanes Used in Rubber Formulations (bis-(triethoxysilylpropyl)sulfanes): Characterization by Gas Chromatography (GC) |
|
ASTM D 6977 |
Standard Specification for Polychloroprene Examination Gloves for Medical Application |
|
ASTM D 6854 |
Standard Test Method for Silica n-Dibutyl Phthalate Absorption Number |
|
ASTM D 7129 |
Standard Test Method for Determination of Ammonia Trapping in a Grafted Battery Separator |
|
ASTM D 7050 |
Standard Practice for Rubber from Natural SourcesSampling and Sorting Bales Based on Predicted Processing Properties |