|
BSI BS ISO 10100 |
Hydraulic Fluid Power - Cylinders - Acceptance Tests |
|
BSI BS ISO 10372 |
Hydraulic Fluid Power - Four-and Five-Port Servovalves - Mounting Surfaces-Supersedes BS 6494-2: 1986; |
|
BSI BS ISO 12132 |
Plain Bearings - Quality Assurance of Thin-Walled Half Bearings - Design FMEA |
|
BSI BS ISO 15031-5 |
Road vehicles Communication between vehicle and external equipment for emissions-related diagnostics Part 5: Emissions-related diagnostic services |
|
BSI BS ISO 3553-2 |
Road Vehicles - High Tension Connectors for Ignition Coils and Distributors Part 2: Plug Types |
|
BSI BS ISO 4161 |
Hexagon Nuts with Flange - Coarse Thread |
|
BSI BS ISO 9981 |
Belt Drives - Pulleys and V-Ribbed Belts for the Automotive Industry - PK Profile: Dimensions-Supersedes BS AU 248: 1993; |
|
BSI BS ISO/TS 13725 |
Hydraulic Fluid Power - Cylinders - Method for Determining the Buckling Load |
|
BSI DD ENV 50142 |
Electromagnetic Compatibility - Basic Immunity Standard - Surge Immunity Tests (E) |
|
BSI BS 1075 |
Tungsten Halogen Lamps (Non-Vehicle)-AMD 13025: September 20, 2001; EN 60357:1988; |
|
BSI BS 1552 |
Open Bottomed Taper Plug Valves for 1st, 2nd and 3rd Family Gases up to 200 mbar-AMD 9622: September 1997 |
|
BSI BS 2464 PART 3 |
Hose Couplings for Petrol, Oil and Lubricants Part 3: Quick-Acting Couplings |
|
BSI BS 2519 PART 2 |
Glossary for Gears Part 2: Notation |
|
BSI BS 2827 |
Machine Screw Nuts, Pressed Type B.A. & Whitworth Form Threads (AMD 1880) January 30, 1976-Amd 1; |
|
BSI BS 6102 PART 14 |
Cycles Part 14: Specification for Dimensions of Bottom Bracket Axle and Crank Assembly with Square End Fittings (ISO 6695: 1991) |
|
BSI BS 6226 |
Low Voltage Switchgear and Controlgear for Industrial Use. Inductive Proximity Switches. Definitions, Classification and Designation |
|
BSI BS 6347-6 |
Performance assessment of agricultural tractors Part 6: Method for determination of centre of gravity-AMD 9584: August 1997; ISO 789-6: 1982; |
|
BSI BS 6487 |
Split Pin Holes and Wire Holes in Bolts, Screws and Studs |
|
BSI BS 6910 PART 2 |
Cold Pour Resin Compound and Heat-Shrink Cable Joints in the Voltage Range up to 1000 V a.c. and 1500 V d.c.: Part 2: Code of Practice for On-Site Installation (Read in Conjunction BS 6910: Part 1) |
|
BSI BS 6997 |
Elastomeric Toroidal Sealing Rings (O-Rings) Manufactured from Acrylonitrile-Butadiene Rubbers Complying with BS 6996 |
|
BSI BS 7628 |
Combined Transformers (E) |
|
BSI BS 7751-2 |
Prevailing torque type wire thread inserts Part 2: Specification for ISO metric fine pitch threads-AMD 16654: October 31, 2006 |
|
BSI BS 7901 |
Specification for Recovery Vehicles and Vehicle Recovery Equipment-CORR 14002: July 23, 2002; |
|
BSI BS AU 138B |
Towing Vehicle, Trailer and Semi-Trailer Pneumatic Braking Systems - |
|
BSI BS AU 206 PART 4 |
Diagnostic Systems for Road Vehicles Part 4: General Requirements for Testing Electronic Systems |
|
BSI BS AU 234 |
Methods of Test and General Requirements for Road Vehicle Starter Motors |
|
BSI BS AU 25 |
Towing Hook for Use Between Trailers of 5 to 14 Tons Gross Weight and Towing Vehicle |
|
BSI BS AU 265 PART 2 |
Road Vehicles - Ignition Systems Part 2: Electrical Performance and Function Test Methods-AMD 9610; September 1997; ISO 6518-2: 1995; |
|
BSI BS AU 267 |
Breakaway Cables and Secondary Couplings |
|
BSI BS AU 50PT4: SUBSEC 5.1 |
Tyres and Wheels Part 4: Rim Profiles and Dimensions Section 5: Industrial Vehicle Rims Subsection 5.1: Specification for Rim Profiles and Dimensions for Code-Designated Series Tyres (E) |
|
BSI BS EN 13160-3 |
Leak detection systems Part 3: Liquid systems for tanks |
|
BSI BS EN 13803-2 |
Railway applications  Track  Track alignment design parameters  Track gauges 1435 mm and wider  Part 2: Switches and crossings and comparable alignment design situations with abrupt changes of curvature |
|
BSI BS EN 50186-1 |
Live-Line Washing Systems for Power Installations with Nominal Voltages Above 1 kV - Part 1: Common Requirements |
|
BSI BS EN 60095-2 |
Lead-Acid Starter Batteries Part 2: Dimensions of Batteries and Dimensions and Marking of terminals (AMD 8738) October 15, 1995 (E)-Amd 8738: October 15, 1995 |
|
BSI BS EN 60317-7 |
Specifications for Particular Types of Winding Wires Part 7: Polyimide Enamelled Round Copper Wire, Class 220-AMD 8891: November 1995; AMD 10304: May 1999; Renumbers BS 6811 SEC 3.8:1993; IEC 60317-7:1990 |
|
BSI BS EN 60357 |
Tungsten halogen lamps (non-vehicle) Performance specifications |
|
BSI BS EN 60660 |
Insulators - Tests on Indoor Post Insulators of Organic Material for Systems with Nominal Voltages Greater Than 1 kV up to but Not Including 300 kV-IEC 60660:1999; |
|
BSI BS EN 60851-6 |
Winding Wires - Test Methods - Part 6: Thermal Properties-AMD 15109: May 12, 2004; Supersedes BS 6811-2.6: 1987; IEC 60851-6: 1996; |
|
BSI BS EN 60968 |
Self-Ballasted Lamps for General Lighting Services - Safety Requirements-AMD 6707: September 1991; AMD 7716: May 1993; AMD 10815: July 2000; Renumbers BS 7173: 1989 |
|
BSI BS EN 60998-2-4 |
Connecting Devices for Low-Voltage Circuits for Household and Similar Purposes - Part 2-4: Particular Requirements for Twist-on Connecting Devices |
|
BSI BS EN 61466-2 |
Composite string insulator units for overhead lines with a nominal voltage greater than 1 kV Part 2: Dimensional and electrical characteristics-AMD 13906: October 17, 2002;:1998 |
|
BSI BS EN 61549 |
Miscellaneous lamps-AMD 15781: August 31, 2006 |
|
BSI BS EN 61811-10 |
Electromechanical elementary relays of assessed quality Part 10: Sectional specification Relays for industrial application |
|
BSI BS EN 62133 |
Secondary cells and batteries containing alkaline or other non-acid electrolytes Safety requirements for portable sealed secondary cells, and for batteries made from them, for use in portable applications |
|
BSI BS EN 720-1 |
Transportable Gas Cylinders - Gases and Gas Mixtures - Part 1: Properties of Pure Gases |
|
BSI BS EN 751-2 |
Sealing Materials for Metallic Threaded Joints in Contact with 1st, 2nd and 3rd Family Gases and Hot Water Part 2: Non-Hardening Jointing Compounds-Supersedes BS 6956: Part 6: 1992; |
|
BSI BS EN 855 |
Plastics Hoses and Hose Assemblies - Thermoplastics Textile Reinforced Hydraulic Type - Specification-This Standard is a Revision of BS 4983: 1992; |
|
BSI BS EN ISO 11114-1 |
Transportable Gas Cylinders - Compatibility of Cylinder and Valve Materials with Gas Contents - Part 1: Metallic Materials |
|
BSI BS EN ISO 11114-3 |
Transportable Gas Cylinders - Compatibility of Cylinder and Valve Materials with Gas Contents Part 3: Autogenous Ignition Test in Oxygen Atmosphere |
|
BSI BS EN ISO 16047 |
Fasteners Torque/clamp force testing |
|
BSI BS EN ISO 2505 |
Thermoplastics pipes Longitudinal reversion Test method and parameters-:1995 |
|
BSI BS EN ISO 7233 |
Rubber and Plastics Hoses and Hose Assemblies - Determination of Suction Resistance (ISO 7233: 1991) (AMD 8144) July 15, 1995 (Formerly BS 5173: Section 102.9: 1992. Replaces 5173-102-9: 1985) (E)-Amd 1; |
|
BSI BS IEC 1000-3-7 |
Electromagnetic Compatibility (EMC) Part 3: Limits Section 7: Assessment of Emission Limits for Fluctuating Loads in MV and HV Power Systems - Basic EMC Publication |
|
BSI BS ISO 11922-2 |
Thermoplastics Pipes for the Conveyance of Fluids - Dimensions and Tolerances Part 2: Inch-Based Series-Together with BS 2782: Part 11: Method 1121C and BS ISO 4065, This Document Partially Supersedes BS 3867: 1987; |
|
BSI BS ISO 4156-3 |
Straight cylindrical involute splines  Metric module, side fit  Part 3: Inspection |
|
BSI BS ISO 8140 |
Pneumatic Fluid Power - Cylinders, 1 000 kPa (10 Bar) Series - Rod End Clevis - Mounting Dimensions (E) |
|
BSI BS ISO TR 10064-1 |
Code of inspection practice  Part 1: Inspection of corresponding flanks of gear teeth-CORR 16760: November 30, 2006 |
|
BSI DD CEN/TS 14825 |
Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling Testing and rating at part load conditions |
|
BSI BS 2767 |
Manually Operated Copper Alloy Valves for Radiators-AMD 13147: December 3, 2001; |
|
BSI BS 61 |
Threads for Light Gauge Copper Tubes and Fittings-AMD 4431: April 30, 1984 |
|
BSI BS 6102 PART 4 |
Cycles Part 4: Glossary of Terms (ISO 8090: 1990) |
|
BSI BS 6130 PART 1 |
Hose and Hose Assemblies for Asphalt and Bitumen Part 1: Specification for Flexible Metallic Hose and Hose Assemblies (E) |
|
BSI BS 6605 |
Cross Recesses for Screws (AMD 8513) May 15, 1995 (E)-Amd 1; |
|
BSI BS 7264 PART 2 |
Shunt Capacitors for a.c. Power Systems Having a Rated Voltage Above 1000V Part 2: Guide to Endurance Testing (AMD 7530) February 15, 1993-Amd 1; |
|
BSI BS 7506 PART 2 |
Methods for Measurements in Electrostatics Part 2: Test Methods-AMD 9720; December 15, 1997; |
|
BSI BS 7520 |
Guide to Quality assurance plans for tools for live working-CORR 13958: December 10, 2002; IEC 61318: 1994; |
|
BSI BS 7578 |
Coupling Capacitors and Capacitor Dividers (IEC 358: 1990) |
|
BSI BS AU 180 PART 4 |
Brake Linings Part 4: Method for Determining Effects of Heat on Dimensions and Form of Disc Brake Pads |
|
BSI BS AU 222 |
Method of Evaluating Surface and Material Flaws of Disc Brake Pads After Testing |
|
BSI BS AU 24A |
Towing Connections for Trailers of up to 5000 kg Gross Mass |
|
BSI BS EN 12483 |
Liquid Pumps - Pump Units with Frequency Inverters - Guarantee and Compatibility Tests |
|
BSI BS EN 13423 |
Compressed Natural Gas Vehicle Operations |
|
BSI BS EN 14420-1 |
Hose fittings with clamp units Part 1: Requirements, survey, designation and testing |
|
BSI BS EN 28738 |
Plain Washers for Clevis Pins - Product Grade A (ISO 8738: 1986) (E) |
|
BSI BS EN 3112 |
Bolts, Normal Hexagonal Head, Threaded to Head, in Alloy Steel, Cadmium Plated - Classification: 900 MPa (at Ambient Temperature)/235 Degrees C (E) |
|
BSI BS EN 489 |
District heating pipes Preinsulated bonded pipe systems for directly buried hot water networks Joint assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
|
BSI BS EN 50363-6 |
Insulating, sheathing and covering materials for low voltage energy cables Part 6: Halogen-free, cross-linked sheathing compounds-Supersedes BS 7655-8.1: 2000 |
|
BSI BS EN 60061-4 |
Lamp Caps and Holders Together with Gauges for the Control of Interchangeability and Safety - Part 4: Guidelines and General Information-AMD 9308: August 1996; AMD 10189: March 1999; AMD 13137: September 2001; AMD 13589: September 17, 2002; AMD 14572: September 8,2003; AMD 15559: May 6, 2005 |
|
BSI BS EN 60216-4-3 |
Electrical Insulating Materials - Thermal Endurance Properties - Part 4-3: Ageing Ovens - Multi-chamber Ovens |
|
BSI BS EN 60359 |
Electrical and Electronic Measurement Equipment - Expression of Performance-Supersedes BS 4889: 1990; IEC 60359: 2001; |
|
BSI BS EN 60512-11-6 |
Connectors for Electronic Equipment - Tests and Measurements - Part 11-6: Climatic Tests - Test 11f: Corrosion, Salt Mist |
|
BSI BS EN 61046 |
D.C. or A.C. Supplied Electronic Step-Down Convertors for Filament Lamps - General and Safety Requirements-AMD 9152: November 15, 1996; Superseded by BS EN 61347-1:2001 and BS EN 61347-2-2:2001 but remains current |
|
BSI BS EN 61211 |
Insulators of ceramic material or glass for overhead lines with a nominal voltage greater than 1 000 V Impulse puncture testing in air-Supersedes BS 7803:1995 |
|
BSI BS EN 61243-5 |
Live Working - Voltage Detectors - Part 5: Voltage Detecting Systems (VDS) |
|
BSI BS EN 61284 |
Overhead Lines - Requirements and Tests for Fittings-Amd 1; CORR 13778: July 4, 2002; IEC 61284: 1997; |
|
BSI BS EN 61466-1 |
Composite string insulator units for overhead lines with a nominal voltage greater than 1 000 V Part 1: Standard strength classes and end fittings-:1997 |
|
BSI BS EN ISO 14580 |
Hexalobular socket cheese head screws-CORR 13767: March 12, 2002; CORR 16233: August 31, 2006 |
|
BSI BS EN ISO 15978 |
Open end blind rivets with break pull mandrel and countersunk head AIA/St-CORR 14327: February 4, 2003; CORR 15346: November 29, 2004; BS EN ISO 14588:2001, Together with BS EN ISO 14588:2001, BS EN ISO 14589:2001, BS EN ISO 15973:2000, BS EN ISO 15974:2001, BS EN ISO 15975:2002, BS EN ISO 15976:2002, BS EN ISO 15977:2002 and BS EN ISO 15979:2002 supersedes BS 7349-1:1993 |
|
BSI BS EN ISO 2010 |
Countersunk Slotted Raised Head Screws (Common Head Style) - Product Grade A (E) |
|
BSI BS EN ISO 5774 |
Plastic Hoses, Textile-Reinforced, for Compressed Air - Specification-Supersedes BS 6066:1981; |
|
BSI BS EN ISO 7093-2 |
Plain Washers - Large Series - Part 2: Product Grade C |
|
BSI BS ISO 15031-6 |
Road vehicles Communication between vehicle and external equipment for emissions-related diagnostics Part 6: Diagnostic trouble code definitions |
|
BSI BS ISO 15750-1 |
Packaging - Steel Drums - Part 1: Removable Head (Open Head) Drums with a Minimum Total Capacity of 208 1, 210 1 and 216,51 |
|
BSI BS ISO 2575 |
Road Vehicles Symbols for controls, indicators and tell-tales-AMD 16361: July 31, 2006 |
|
BSI BS ISO 2790 |
Belt drives V-belts for the automotive industry and corresponding pulleys Dimensions |
|
BSI BS ISO 3764 |
Timekeeping Instruments - Movements - Forms, Dimensions and Nomenclature |
|
BSI BS ISO 3911 |
Wheels and rims for pneumatic tyres Vocabulary, designation and marking-Supersedes BS AU 50-2.0B:2000 |
|
BSI BS ISO 6195 |
Fluid power systems and components Cylinder-rod wiper-ring housings in reciprocating applications Dimensions and tolerances-Supersedes BS 6852:1987; |
|
BSI BS ISO 7180 |
Pneumatic Fluid Power - Cylinders - Bore and Port Thread Sizes |
|
BSI BS 2464 PART 4 |
Hose Couplings for Petrol, Oil and Lubricants Part 4: 100 mm Quick-Acting Couplings: European Type |
|
BSI BS 2580 |
Underground Plug Cocks for Cold Water Services (Scottish Type) |
|
BSI BS 3092 |
Main Friction Clutches, Main Power-Take-Off Assemblies and Associated Attachment for Internal Combustion Engines |
|
BSI BS 3537 |
Gudgeon Pins up to 200 mm Diameter |
|
BSI BS 4371 |
Fibrous Gland Packings (E) |
|
BSI BS 4480-2 |
Plain bearings: metric series - Part 2: Solid plastic bushes |
|
BSI BS 5564 |
High-Voltage Fuses for the External Protection of Shunt Power Capacitors (AMD 6686) April 30, 1991-Amd 1; |
|
BSI BS 5590 |
Screw Thread Metric Series Measuring Cylinders-Amd 1; |
|
BSI BS 5601 PART 1 |
Code of Practice for Ventilation and Heating of Caravans Part 1: Ventilation-AMD 8564; March 15, 1995; Superseded by BS EN 721: 1999; |
|
BSI BS 5714 |
(OBSOLESCENT)1979 Measurement of Resistivity of Metallic Materials |
|
BSI BS 6005 |
Moulded Transparent Polycarbonate Bowls Used in Compressed Air Filters and Lubricators |
|
BSI BS 6102 PART 13 |
Cycles Part 13: Specification for Mating Dimensions for Splined Hub and Sprocket (ISO 10230: 1990) |
|
BSI BS 6273 |
Low Voltage Switchgear and Controlgear for Industrial Use. Mounting Rails. Top Hat Rails, 15 mm Wide for the Fixing of Terminal Blocks |
|
BSI BS 7388 |
Guide for Prevention of Leaks from Hydraulic Fluid Power Systems |
|
BSI BS 7403 PART 5 |
Full-Flow Lubricating Oil Filters for Internal Combustion Engines Part 5: Method of Test for Cold Start Simulation and Hydraulic Pulse Durability (ISO 4548-5: 1990) |
|
BSI BS 7612 |
Non-Circular Steel Wire for Mechanical Springs-AMD 10289; March, 1999; |
|
BSI BS 7615 |
Motor Cycle Chains (ISO 10190: 1992) (E) |
|
BSI BS 7698-10 |
Reciprocating Internal Combustion Engine Driven Alternating Current Generating Sets - Part 10: Measurement of Airborne Noise by the Enveloping Surface Method-ISO 8528-10: 1998; |
|
BSI BS 7922 |
Electric cables Fluid-filled, paper- and PPL-insulated, metal-sheathed cables and accessories for alternating voltages up to and including 400 kV (Um = 420 kV) Requirements and test methods (Implementation of HD 633) |
|
BSI BS AU 149A |
Electrical Connections Between Towing Vehicles and Trailers with 6V or 12V Electrical Equipment: Type 12N (Normal) |
|
BSI BS AU 169A |
Method for Determination of Burning Behaviour of Interior Materials for Road Vehicles, and Tractors and Machinery for Agriculture and Forestry (ISO 3795: 1989) |
|
BSI BS AU 181 |
Interface dimensions for demountable vehicle body systems |
|
BSI BS AU 187 |
Tow Rope Assemblies for Towing Passenger Cars and Light Vans |
|
BSI BS AU 201 PART 2 |
Relays and Flashers Part 2: Arrangement and Functional Attribution of Relay Terminals for Road Vehicles |
|
BSI BS AU 203A |
Dimensions of Couplings Between Power Take offs (PTOs) and Ancillary Driven Units on Commercial Road Vehicles |
|
BSI BS AU 206 PART 2 |
Diagnostic Systems for Road Vehicles Part 2: Graphical Symbols for Diagnostic Testers |
|
BSI BS AU 209 PART 1A |
Vehicle Security Part 1a: Specification for Locking Systems for Passenger Cars and Car Derived Vehicles |
|
BSI BS AU 215 PART 3 |
Power Take-Offs (PTOs) Part 3: Dimensions of Connections for Rear Mounted Power Take Offs for Commercial Road Vehicles |
|
BSI BS AU 40 PART 4A |
Motor Vehicle Lighting and Signalling Equipment Part 4a: Sealed Beam Headlamps (Formerly BS AU 40: Part 4: 1966)-Amd 1; |
|
BSI BS AU 50 PT 1: SEC 8 |
Tyres and Wheels Part 1: Tyres Section 8: Code of Practice for the Storage of Tyres, Inner Tubes and Flaps |
|
BSI BS AU 50-1-4.2B |
Tyres and Wheels - Part 1: Tyres - Section 4: Agricultural Tractor and Machine Tyres - Subsection 4.2b: Specification for Load Ratings for Ply Rating Marked Series Tyres-ISO 4251-2: 1998; |
|
BSI BS AU50PT4: SUBSEC5.2 |
Tyres and Wheels Part 4: Rim Profiles and Dimensions Section 5: Industrial Vehicle Rims Subsection 5.2: Specification for Rim Profiles and Dimensions for Metric Series Pneumatic Tyres and Solid Tyres for Pneumatic Tyre Rims-ISO 3739-3: 1995; |
|
BSI BS EN 13483 |
Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems Specification |
|
BSI BS EN 1555-2 |
Plastics piping systems for the supply of gaseous fuels Polyethylene (PE) Part 2: Pipes |
|
BSI BS EN 1663 |
Prevailing Torque Type Hexagon Nuts with Flange (with Non-Metallic Insert) |
|
BSI BS EN 1664 |
Prevailing Torque Type All-Metal Hexagon Nuts with Flange |
|
BSI BS EN 50066 |
Mini-Couplers for the Interconnection of Electrical Mains Supplied Equipment in Road Vehicles (E) |
|
BSI BS EN 50107-1 |
Signs and luminous-dischargetube installations operating from a no-load rated output voltage exceeding 1 kV but not exceeding 10 kV Part 1: General requirements-AMD 15146: April 29, 2004; Supersedes BS EN 50107:1998 |
|
BSI BS EN 50143 |
Cables for Signs and Luminous-Discharge-Tube Installations Operating from a No-Load rated Output Voltage Exceeding 1 kV but Not Exceeding 10 kV-AMD 14592: October 17, 2003; Supersedes BS 5055: 1991; |
|
BSI BS EN 50363-1 |
Insulating, sheathing and covering materials for low voltage energy cables Part 1: Cross-linked elastomeric insulating compounds-:2000 |
|
BSI BS EN 50363-2-2 |
Insulating, sheathing and covering materials for low voltage energy cables Part 2-2: Cross-linked elastomeric covering compounds |
|
BSI BS EN 60095-4 |
Lead-Acid Starter Batteries Part 4: Dimensions of Batteries for Heavy Commercial Vehicles (AMD 8739) October 15, 1995 (E)-Amd 1; |
|
BSI BS EN 60143-3 |
Series Capacitors for Power Systems Part 3: Internal Fuses-Supersedes BS 7633: 1993; IEC 60143-3: 1998; |
|
BSI BS EN 60264-3-4 |
Packaging of Winding Wires - Part 3-4: Taper Barrelled Delivery Spools - Basic Dimensions of Containers for Taper Barrelled Delivery Spools-IEC 60264-3-4: 1999; |
|
BSI BS EN 60512-2-6 |
Connectors for Electronic Equipment - Tests and Measurements - Part 2-6: Electrical Continuity and Contact Resistance Tests - Test 2f: Housing (Shell) Electrical Continuity |
|
BSI BS EN 60684-3-233 |
Flexible insulating sleeving Part 3: Specifications for individual types of sleeving Sheet 233: Heat-shrinkable fluoroelastomer sleeving, flame retarded, fluid resistant, shrink ratio 2:1-CORR 16839: January 31, 2007 |
|
BSI BS EN 60851-4 |
Winding wires Test methods Part 4: Chemical properties-AMD 15710: March 14, 2006 |
|
BSI BS EN 60999-2 |
Connecting devices Electrical copper conductors Safety requirements for screw-type and screwless-type clamping units Part 2: Particular requirements for clamping units for conductors above 35 mm2 up to 300 mm2 (included) |
|
BSI BS EN 61044 |
Opportunity-Charging of Lead-Acid Traction Batteries (IEC 1044: 1990) (E) |
|
BSI BS EN 61047 |
DC or AC supplied electronic step-down convertors for filament lamps Performance requirements |
|
BSI BS EN 61058-2-4 |
Switches for appliances Part 2-4: Particular requirements for independently mounted switches |
|
BSI BS EN 61210 |
Connecting Devices - Flat Quick-Connect Terminations for Electrical Copper Conductors - Safety Requirements |
|
BSI BS EN 61316 |
Industrial Cable Reels |
|
BSI BS EN 61809 |
Secondary Cells and Batteries Containing Alkaline or Other Non-Acid Electrolytes - Safety Requirements for Portable Sealed Alkaline Secondary Cells and Batteries-IEC 61809:2000; Superseded by BS EN 62133: 2003 |
|
BSI BS EN 61959 |
Secondary cells and batteries containing alkaline or other non-acid electrolytes Mechanical tests for sealed portable secondary cells and batteries |
|
BSI BS EN 62196-1 |
Plugs, socket-outlets, vehicle couplers and vehicle inlets Conductive charging of electric vehicles Part 1: Charging of electric vehicles up to 250 A a.c. and 400 A d.c. |
|
BSI BS EN 815 |
Safety of Unshielded Tunnel Boring Machines and Rodless Shaft Boring Machines for Rock-AMD 17029: April 30, 2007 |
|
BSI BS ISO 10762 |
Hydraulic Fluid Power - Cylinder Mounting Dimensions - 10 MPa (100 Bar) Series |
|
BSI BS ISO 11451-4 |
Road vehicles Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy Part 4: Bulk current injection (BCI) |
|
BSI BS ISO 12103-2 |
Road Vehicles - Test Dust for Filter Evaluation Part 2: Aluminium Oxide Test Dust |
|
BSI BS ISO 12240-3 |
Spherical Plain Bearings - Part 3: Thrust Spherical Plain Bearings |
|
BSI BS ISO 12353-1 |
Road Vehicles - Traffic Accident Analysis - Part 1: Vocabulary |
|
BSI BS ISO 13556 |
Road Vehicles - Localization of Exhaust System Leaks and Equipment Specifications |
|
BSI BS ISO 15171-2 |
Connections for Fluid Power and General Use - Hydraulic Couplings for Diagnostic Purposes - Part 2: Coupling with M16 x 2 End for Connection Under Pressure |
|
BSI BS ISO 16750-2 |
Road vehicles Environmental conditions and testing for electrical and electronic equipment Part 2: Electrical loads |
|
BSI BS ISO 199 |
Rolling Bearings - Thrust Bearings - Tolerances |
|
BSI BS ISO 22902-1 |
Road vehicles Automotive multimedia interface Part 1: General technical overview |
|
BSI BS ISO 22902-3 |
Road vehicles Automotive multimedia interface Part 3: System requirements |
|
BSI BS ISO 22902-7 |
Road vehicles Automotive multimedia interface Part 7: Physical specification |
|
BSI BS ISO 23273-3 |
Fuel cell road vehicles Safety specifications Part 3: Protection of persons against electric shock |
|
BSI BS ISO 2534 |
Road Vehicles - Engine Test Code - Gross Power |
|
BSI BS ISO 2704 |
Road Vehicles - M10 X 1 Spark Plugs with Flat Seating and Their Cylinder Head Housings |
|
BSI BS ISO 2942 |
Hydraulic fluid power Filter elements Verification of fabrication integrity and determination of the first bubble point-Supersedes BS 6275 Part 2: 1984 |
|
BSI BS ISO 4000-2 |
Passenger car tyres and rims  Part 2: Rims |
|
BSI BS ISO 4926 |
Road vehicles  Hydraulic braking systems  Non-petroleum-base reference fluids |
|
BSI BS ISO 582 |
Rolling Bearings - Chamfer Dimensions - Maximum Values (E) |
|
BSI BS ISO 6301-1 |
Pneumatic Fluid Power - Compressed Air Lubricators - Part 1: Main Characteristics to Be Included in Supplier's Literature and Product-Marking Requirements |
|
BSI BS ISO 6722 |
Road vehicles 60V and 600V single core cables Dimensions, test methods and requirements |
|
BSI BS ISO 7181 |
Hydraulic Fluid Power - Cylinders - Bore and Rod Area Ratios |
|
BSI BS ISO/IEC 1989 |
Information technology Programming languages COBOL-Supersedes BS EN ISO 1989:1996; |
|
BSI BS ISO/TR 10495 |
Cylindrical Gears - Calculation of Service Life under Variable Load - Conditions for Cylindrical Gears in Accordance with ISO 6336 |
|
BSI PD IEC TR 60721-4-4 |
Classification of Environmental Conditions - Part 4-4: Guidance for the Correlation and Transformation of Environmental Condition Classes of IEC 60721-3 to the Environmental Test of IEC 60068 - Stationary Use at Non-Weatherprotected Locations-AMD 14598: October 10, 2003; |
|
BSI BS 5244 |
Recommendations for Application, Storage and Life Expiry of Hydraulic Rubber Hose and Assemblies |
|
BSI BS 5540 PART 7 |
Evaluating Particulate Contamination of Hydraulic Fluids Part 7: Method of Determining the Level of Contamination (by the Gravimetric Method) (ISO 4405: 1991) (E) |
|
BSI BS 5585 |
Low-Voltage Switch Gear and Controlgear for Industrial Use. Mounting Rails. Top Hat Rails 75 mm Wide for Snap-On Mounting of Equipment |
|
BSI BS 5935 |
Toroidal Strip-Wound Cores Made of Magnetically Soft Material-AMD 9874; February 15, 1998; IEC 60635: 1978; |
|
BSI BS 5944 PART 1 |
Measurement of Airborne Noise from Hydraulic Fluid Power Systems and Components Part 1: Method of Test for Pumps (E) (ISO 4412-1: 1991) |
|
BSI BS 6122 |
Low Voltage Switchgear and Controlgear for Industrial Use. Inductive Proximity Switches. Form C for Alternating Current 2 Terminals |
|
BSI BS 6356 PART 1 |
Spraying Equipment for Crop Protection Part 1: Method of Test for Sprayer Nozzles-ISO 5682-1:1996; |
|
BSI BS 6361 |
Three-Pin Plug Connectors for Electrically Controlled Fluid Power Equipment |
|
BSI BS 6518 |
Low Voltage Switchgear and Controlgear for Industrial Use. Control Switches. Position Switches 43.5 X 80; Dimensions and Characteristics |
|
BSI BS 6528 |
Terms for Cylindrical Screw Threads |
|
BSI BS 7764 |
Hexagon Slotted Nuts and Castle Nuts (E) |
|
BSI BS 949-3 |
Screwing taps Part 3: Specification for pipe thread taps-AMD 7927: September 1993; |
|
BSI BS 978 PART 2 |
Fine Pitch Gears Part 2: Cycloidal Type Gears-AMD 2407: March 1956; AMD 4569: May 1962 |
|
BSI BS AU 156 |
Recommendations for Aiming of headlamps and auxiliary lamps on motor vehicles |
|
BSI BS AU 162A |
Specification for Headlamp optical aiming devices-AMD 2247: March, 1977 |
|
BSI BS AU 175 PART 1B |
Vehicle Identification Numbers (VIN) Part 1B: Content and Structure-Amd 1; |
|
BSI BS AU 180 PART 2 |
Brake Linings Part 2: Method for Measurement of Internal Shear Strength of Lining Material |
|
BSI BS AU 233 |
Starter Motor Electrical Connections for Passenger Cars |
|
BSI BS AU 246 |
Method for Determination of the Centre of Gravity of Road Vehicles with Two Axles (ISO 10392: 1992) (E) |
|
BSI BS AU 264 |
Road Vehicles - M18 X 1,5 Spark- Plugs with Conical Seating and Their Cylinder Head Housing (ISO 2345: 1994) (E) |
|
BSI BS AU 50-1.6.1B |
Tyres and wheels Part 1: Tyres Section 6: Motorcycle tyres Subsection 6.1b: Specification for general and load ratings for metric series tyres-AMD 10594: October 1999;:1995; ISO 5751-1:1994 |
|
BSI BS EN 12502-2 |
Protection of metallic materials against corrosion Guidance on the assessment of corrosion likelihood in water distribution and storage systems Part 2: Influencing factors for copper and copper alloys |
|
BSI BS EN 1277 |
Plastics Piping Systems - Thermoplastics Piping Systems for Buried Non- Pressure Applications - Test Methods for Leaktightness of Elastomeric Sealing Ring Type Joints |
|
BSI BS EN 12817 |
LPG equipment and accessories Inspection and re-qualification of LPG tanks up to and including 13 m3 overground-AMD 16180: August 31, 2006 |
|
BSI BS EN 13081 |
Tanks for Transport of Dangerous Goods - Service Equipment for Tanks - Vapour Collection Adapter and Coupler |
|
BSI BS EN 13906-3 |
Cylindrical Helical Springs Made from Round Wire and Bar - Calculation and Design - Part 3: Torsion Springs-Together with BS 8726-2: 2002 and BS 1726-3: 2002, Supersedes BS 1726-3: 1988; |
|
BSI BS EN 14125 |
Thermoplastic and flexible metal pipework for underground installation at petrol filling stations-AMD 16792: December 29, 2006 |
|
BSI BS EN 1977 |
Copper and Copper Alloys - Copper Drawing Stock (Wire Rod) |
|
BSI BS EN 26157-1 |
Fasteners - Surface Discontinuities Part 1: Bolts, Screws and Studs for General Requirements (ISO 6157-1: 1988) |
|
BSI BS EN 2648 |
Washers, Concave, in Alloy Steel, Cadmium Plated (E) |
|
BSI BS EN 26802 |
Rubber and Plastic Hose and Hose Assemblies - Wire Reinforced - Hydraulic Impulse Test with Flexing (ISO 6802: 1991) (AMD 7521) April 15, 1993 (Formerly BS 5173: Section 102.6 Replaces BS 5173: Part 102: Section 102.6: 1985)-Amd 1; |
|
BSI BS EN 27436 |
Slotted Set Screws with Cup Point (ISO 7436: 1983) |
|
BSI BS EN 50186-2 |
Live-Line Washing Systems for Power Installations with Nominal Voltages Above 1 kV - Part 2: National Annexes |
|
BSI BS EN 50363-8 |
Insulating, sheathing and covering materials for low voltage energy cables Part 8: Halogen-free, thermoplastic sheathing compounds |
|
BSI BS EN 521 |
Specifications for dedicated liquefied petroleum gas appliances Portable vapour pressure liquefied petroleum gas appliances |
|
BSI BS EN 60133 |
Dimensions of Pot-Cores Made of Magnetic Oxides and Associated Parts-Supersedes BS 4061-1:1987(1997); |
|
BSI BS EN 60264-1 |
Packaging of Winding Wires Part 1: Containers for Round Winding Wires (IEC 264-1: 1968) (AMD 9047) May 15, 1996 (E)-Amd 1; |
|
BSI BS EN 60264-3-5 |
Packaging of Winding Wires - Part 3-5: Taper Barrelled Delivery Spools - Specification for Spool Containers Made from Thermoplastic Material-IEC 60264-3-5: 1999; |
|
BSI BS EN 60317-20 |
Specifications for Particular Types of Winding Wires Part 20: Solderable Polyurethane Enamelled Round Copper Wire, Class 155-AMD 10927: August 2000; Renumbers BS 6811: Section 3.9: 1993; IEC 60317-20: 1990; |
|
BSI BS EN 60371-3-1 |
Specification for Insulating Materials Based on Mica Part 3: Specifications for Individual Materials Sheet 1: Commutator Separators and Materials (IEC 371-3-1: 1984) (F) |
|
BSI BS EN 60464-1 |
Varnishes Used for Electrical Insulation - Part 1: Definitions and General Requirements-AMD 16348: 5/31/2006; Supersedes BS 5629-1: 1978; IEC 60464-1: 1998 |
|
BSI BS EN 60630 |
Maximum Lamp Outlines for Incandescent Lamps-AMD 14562: January 2000; |
|
BSI BS EN 60684-3-216 |
Flexible insulating sleeving Part 3: Specifications for individual types of sleeving Sheet 216: Heat-shrinkable, flame-retarded, limited-fire hazard sleeving |
|
BSI BS EN 60998-2-3 |
Connecting devices for low-voltage circuits for household and similar purposes  Part 2-3: Particular requirements for connecting devices as separate entities with insulation-piercing clamping units-Incorporates CORR 16841: January 31, 2007 |
|
BSI BS EN 61057 |
Aerial devices with insulating boom used for live working exceeding 1 kV a.c.-CORR 16395: August 2006; CORR 13865: October 4, 2002; |
|
BSI BS EN 61248-1 |
Transformers and Inductors for Use in Electronic and Telecommunication Equipment Part 1: General Specification-IEC 61248-1: 1996; |
|
BSI BS EN 61812-1 |
Specified Time Relays for Industrial Use - Part 1: Requirements and Tests-AMD 10542: March 2000 |
|
BSI BS EN 61858 |
Electrical Insulation Systems - Thermal Evaulation of Modifications to an Established Wire-Wound EIS |
|
BSI BS EN 62199 |
Bushings for d.c. application |
|
BSI BS EN 751-1 |
Sealing Materials for Metallic Threaded Joints in Contact with 1st, 2nd and 3rd Family Gases and Hot Water Part 1: Anaerobic Jointing Compounds-Supersedes BS 6956: Part 7: 1992; |
|
BSI BS EN 962 |
Transportable Gas Cylinders Valve Protection Caps and Valve Guards for Industrial and Medical Gas Cylinders - Design, Construction and Tests-AMD 11089: May 2001; Supersedes BS 341-1: 1962; |
|
BSI BS EN ISO 1403 |
Rubber Hoses, Textile-Reinforced, for General-Purpose Water Application - Specification-AMD 9703: 11/1997; Renumbers BS ISO 1403: 1995 |
|
BSI BS EN ISO 5674 |
Tractors and machinery for agriculture and forestry Guards for power take-off (PTO) drive-shafts Strength and wear tests and acceptance criteria |
|
BSI BS EN ISO 7085 |
Mechanical and Performance Requirements of Case Hardened and Tempered Metric Thread Rolling Screws |
|
BSI BS EN ISO 8028 |
Rubber and/or Plastics Hose Assemblies for Airless Paint Spraying - Specification-Supersedes BS EN 28028:1993; |
|
BSI BS ISO 10770-1 |
Hydraulic Fluid Power - Electrically Modulated Hydraulic Control Valves - Part 1: Test Methods for Four-Way Directional Flow Control Valves-Supersedes BS 5995: 1980; |
|
BSI BS ISO 10770-2 |
Hydraulic Fluid Power - Electrically Modulated Hydraulic Control Valves - Part 2: Test Methods for Three-Way Directional Flow Control Valves-Supersedes BS 5995: 1980; |
|
BSI BS ISO 1132-2 |
Rolling Bearings - Tolerances - Part 2: Measuring and Gauging Principles and Methods |
|
BSI BS ISO 11943 |
Hydraulic Fluid Power - On-Line Automatic Particle-Counting Systems for Liquids - Methods of Calibration and Validation |
|
BSI BS ISO 12151-1 |
Connections for Hydraulic Fluid Power and General Use - Hose Fittings - Part 1: Hose Fittings with ISO 8434-3 O-Ring Face-Seal Ends |
|
BSI BS ISO 12151-2 |
Connections for hydraulic fluid power and general use Hose fittings Part 2: Hose fittings with ISO 8434-1 and ISO 8434-4 24° cone connector ends with O-rings |
|
BSI BS ISO 12164-2 |
Hollow Taper Interface with Flange Contact Surface - Part 2: Recivers - Dimensions |
|
BSI BS ISO 1436-2 |
Rubber hoses and hose assemblies Wire-braid-reinforced hydraulic types Specification - Part 2: Water-based fluid applications |
|
BSI BS ISO 15243 |
Rolling bearings Damage and failures Terms, characteristics and causes |
|
BSI BS ISO 4141-1 |
Road vehicles Multi-core connecting cables Part 1: Test methods and requirements for basic performance sheathed cables-Supersedes BS AU 231: 1989 |
|
BSI BS ISO 6020-1 |
Hydraulic Fluid Power - Mounting Dimensions for Single Rod Cylinders, 16 Mpa (160 Bar) Series - Part 1: Medium Series-Supersedes BS 6331-1: 1983; |
|
BSI BS ISO 6547 |
Hydraulic Fluid Power - Cylinders - Piston Seal Housings Incorporating Bearing Rings - Dimensions and Tolerances-Supersedes BS 6241:1982; |
|
BSI BS ISO 8085-2 |
Polyethylene Fittings for Use with Polyethylene Pipes for the Supply of Gaseous Fuels - Metric Series - Specifications - Part 2: Spigot Fittings for Butt Fusion, for Socket Fusion Using Heated Tools and for Use with Electrofusion Fittings |
|
BSI BS ISO/TR 7470 |
Valve Outlets for Gas Cylinders - List of Provisions Which Are Either Standardized or in Use-Supersedes PD 6488: 1979; |
|
BSI DD ISO/PAS 27145-2 |
Road vehicles Implementation of WWH-OBD communication requirements Part 2: Common emissions-related data dictionary |
|
BSI PD 6590 |
Recommendations for Dimensional Co-Ordination Between Enclosures and Built-In Devices for Rail Fixing for Household and Similar Installations (E) |
|
BSI PD IEC TR 60721-4-3 |
Classification of Environmental Conditions - Part 4-3: Guidance for the Correlation and Transformation of Environmental Condition Classes of IEC 60721-3 to the Environmental Tests of IEC 60068 - Stationary Use at Weatherprotected Locations-AMD 14605: September 30, 2003; IEC TR 60721-4-3:2001; |
|
BSI PD IEC TR 60721-4-7 |
Classification of environmental conditions Part 4-7: Guidance for the correlation and transformation of environmental condition classes of IEC 60721-3 to the environmental tests of IEC 60068 Portable and non-stationary use-AMD 14601: September 26, 2003; IEC TR 60721-4-7: 2001; |
|
BSI PD IEC/TR 62039 |
Selection guide for polymeric materials for outdoor use under HV stress |
|
BSI PD ISO/TR 17165-2 |
Hydraulic fluid power Hose assemblies Part 2: Recommended practices for hydraulic hose assemblies |
|
BSI BS 1486-2 |
Lubricating Nipples Part 2: Heavy Duty Lubricating Nipples |
|
BSI BS 2069 |
Gas Sampling Tubes |
|
BSI BS 2952 |
Rubber Hose for I.C. Engine Cooling Systems-Amd 2; |
|
BSI BS 325 |
Black Cup and Countersunk Bolts and Nuts-Amd 3; |
|
BSI BS 4368 PART 4 |
Carbon and Stainless Steel Compression Couplings for Tubes Part 4: Type Test Requirements-AMD 4927: September 30, 1985 |
|
BSI BS 5114 |
Performance Requirements for Joints and Compression Fittings for Use with Polyethylene Pipes (AMD 5336) July 31, 1987-Amd 2; |
|
BSI BS 5190 |
Pipeline Filters, Filter Bodies and Filter Elements for Milking Installations |
|
BSI BS 5582 |
Low-Voltage Switch Gear and Controlgear for Industrial Use. Terminal Marking and Distinctive Number for Auxiliary Contacts of Particular Contactors (Detail Rules Based on the General Rules of BS 5472: 1977) |
|
BSI BS 5583 |
Low-Voltage Switch-Gear and Controlgear for Industrial Use. Terminal Marking, Distinctive Number and Distinctive Letter for Particular Contactor Relays (Detailed Rules Based on the General Rules of BS 5472: 1977) |
|
BSI BS 5685 PART 8 |
Electricity Meters Part 8: Impulse Operated Multiple Registers for Use with Induction Electricity Meters |
|
BSI BS 5944 PART 2 |
Measurement of Airborne Noise from Hydraulic Fluid Power Systems and Components Part 2: Method of Test for Motors (ISO 4412-2: 1991) (E) |
|
BSI BS 6102 PART 11 |
Cycles Part 11: Specification for Assembly Dimensions for Stem and Handlebar Bend (ISO 6699: 1990) |
|
BSI BS 6102 PART 16 |
Cycles Part 16: Specification for Replacement Brake-Blocks |
|
BSI BS 6109 PART 2 |
Tail Lifts, Mobile Lifts and Ramps Associated with Vehicles Part 2: Code of Practice for Passenger Lifts and Ramps-AMD 9245 December 15, 1996; Partially superseded by BS EN 1756-2:2004 |
|
BSI BS 6227 |
Low Voltage Switchgear and Controlgear for Industrial Use. Inductive Proximity Switches, Form A for Direct Current. 2 Terminals |
|
BSI BS 6272 |
Low Voltage Switchgear and Controlgear for Industrial Use. Terminal Marking. Terminals for External Associated Electronic Circuit, Components and Contacts |
|
BSI BS 6356 PART 4 |
Spraying Equipment for Crop Protection Part 4: Performance Limits for Field Spraying Nozzles |
|
BSI BS 6520 |
Low Voltage Switchgear and Controlgear for Industrial Use. Control Switches. Position Switches 30 x 55; Dimensions and Characteristics |
|
BSI BS 7540-3 |
Electric cables Guide to use for cables with a rated voltage not exceeding 450/750 V Part 3: National standard cables not included in HD 21 and HD 22-Together with BS 7540-1:2005 and BS 7540-2:2005 supersedes BS 7540:1994 |
|
BSI BS 7814 |
Bolts and Screws Incorporating Either Underhead Locking or Anti-Rotation Features (E) |
|
BSI BS 7894 |
MV impregnated paper insulated distribution cables of rated voltages of 3.8/6.6 kV to 19/33 kV |
|
BSI BS 7923 |
Electric cables Internal gas-pressure cables and accessories for alternating voltages up to and including 275 kV (Um = 300 kV) Requirements and test methods (Implementation of HD 634) |
|
BSI BS 8726-1 |
Cylindrical helical springs made from rectangular and square section wire and bar Guide to calculation and design Part 1: Compression springs-Together with BS 1726-1: 2002 and BS EN 13906-1: 2002, Supersedes BS 1726-1: 1987; |
|
BSI BS AU 159F |
Repairs to Tyres for Motor Vehicles Used on the Public Highway |
|
BSI BS AU 164 |
Measurement of Impact Velocity in Collision Tests on Road Vehicles |
|
BSI BS AU 16A |
Specification for Electrical Cable Connectors (17.5 A Maximum Continuous Rating)-Supersedes BS AU 39):1964 |
|
BSI BS AU 170 |
Measurement of Reflectance of Rear View Mirrors |
|
BSI BS AU 178A |
Specification for Road Vehicle Safety Glass |
|
BSI BS AU 206 PART 1 |
Diagnostic Systems for Road Vehicles Part 1: Glossary |
|
BSI BS AU 206 PART 3 |
Diagnostic Systems for Road Vehicles Part 3: General Requirements for Testing Ignition Systems |
|
BSI BS AU 216 PART 1 |
Hydraulic Brake Systems Using Petroleum Base Brake Fluids for Road Vehicles Part 1: Petroleum Base Reference Fluid |
|
BSI BS AU 223A |
Design, construction performance and marking of vehicle support stands for cars and light vans – Specification-Third Edition |
|
BSI BS AU 227 |
Dimensions of Cylindrical Shaft Ends and Hubs for Alterations for Commercial Vehicles and Buses |
|
BSI BS AU 29 |
Drawbar Eyes and Forecarriage Pins for Connections Between Trailers of 5 and 35 Tons Gross Weight and Towing Vehicle |
|
BSI BS AU 47 |
Advance Warning Triangle to Indicate Temporary Obstructions-Amd 1; |
|
BSI BS EN 12640 |
Securing of Cargo on Road Vehicles - Lashing Points on Commercial Vehicles for Goods Transportation - Minimum Requirements and Testing |
|
BSI BS EN 12736 |
Electrically propelled road vehicles Airborne acoustical noise of vehicle during charging with on-board chargers Determination of sound power level |
|
BSI BS EN 12805 |
Automotive LPG Components - Containers |
|
BSI BS EN 14049 |
Water application intensity Calculation principles and measurement methods |
|
BSI BS EN 1666 |
Prevailing Torque Type Hexagon Nuts with Flange (with Non-Metallic Insert) with Metric Fine Pitch Thread |
|
BSI BS EN 1938 |
Personal Eye Protection - Goggles for Motorcycle and Moped Users-Partially Supersedes BS 4110: 1979, Which has been Revised and Published as BS 4110: 1999; |
|
BSI BS EN 1987-1 |
Electrically Propelled Road Vehicles - Specific Requirements for Safety Part 1: On Board Energy Storage |
|
BSI BS EN 29367-2 |
Lashing and Securing Arrangements on Road Vehicles for Sea Transportation on Ro/Ro Ships - General Requirements Part 2: Semi-Trailers (ISO 9367-2: 1994) (E) |
|
BSI BS EN 50272-4 |
Safety requirements for secondary batteries and battery installations  Part 4: Batteries for use in portable appliances |