|
BSI BS 7823 PART 3 |
Pedestal Plain Bearings Part 3: Specification for Centre Flange Bearings (ISO 11687-3: 1995) (E) |
|
BSI BS AU 146B |
Standard Automatic Roller-Type Coupling for Semi-Trailers Not Exceeding 7 1/4 Tons Laden Weight (Formerly BS AU 146A: 1970)-Amd 1; |
|
BSI BS AU 180 PART 6 |
Brake Linings Part 6: Method for Assessment of Seizure to Ferrous Mating Surface Due to Corrosion |
|
BSI BS AU 188 |
Anchorages for Towing Ropes, Cables or Bars for Road Vehicles |
|
BSI BS AU 200-2A |
Spray Reducing Devices for Heavy Goods Vehicles Part 2A: Performance of Suppression Material and Devices and Air/Water Separating Material and Devices (AMD 5449) August 29, 1986 (Formerly BS AU 200: Part 2: 1984)-Amd 1; |
|
BSI BS AU 220 |
Dimension of 50mm Drawbar Couplings Between Commercial Road Vehicles and Trails |
|
BSI BS AU 249 |
Clutch Housings for Reciprocating Internal Combustion Engines - Nominal Dimensions and Tolerances (ISO 7649: 1991) (E) |
|
BSI BS AU 252 |
Diametral Pitch Starter Motor Pinions for Road Vehicles (ISO 8123: 1991) (E) |
|
BSI BS AU 262-2 |
Road Vehicles - Sheath-Type Glow- Plugs with Conical Seating and Their Cylinder Head Housing Part 2: M12 X 1.25 Glow-Plugs-AMD 14104:December 20, 2002; Also Known as BS ISO 6550-2:1994 |
|
BSI BS AU 266 PART 1 |
Roof Load Carriers Part 1: Roof Bars (ISO 11154-1: 1995) (E) |
|
BSI BS AU 50-3.8 |
Tyres and Wheels - Part 3: Valves - Section 8: Code of Practice for the Selection and Care of Tyre Inflation Valves for Commercial Vehicles-AMD 11053:June 2001; |
|
BSI BS AU 50PT 1:SUBSEC 1.3 |
Tyres and Wheels Part 1: Tyres Section 1: Car Tyres Subsection 1.3: Method of Measuring Rolling Resistance (ISO 8767: 1992) (E) |
|
BSI BS AU 50PT 1:SUBSEC 4.7 |
Tyres and Wheels Part 1: Tyres Section 4: Agricultural Tractor and Machine Tyres Subsec. 4.7: Spec. Marking, Dimensions, Load Ratings and Reference Speeds for Service Desc. Marked Tyres for Agricultural Tractor Drive Wheels (ISO 8664: 1992) |
|
BSI BS AU 50PT 1:SUBSEC 7.1 |
Tyres and Wheels Part 1: Tyres Section 7: Moped Tyres Subsection 7.1: Tyre Designations, Dimensions and Load Ratings |
|
BSI BS AU 50PT1: SUBSEC 5.1 |
Tyres and Wheels Part 1: Tyres Section 5: Industrial Vehicle Tyres Subsection 5.1: Specification for Code-Designated Series Tyres (E) |
|
BSI BS AU 50PT4: SUBSEC 6.3 |
Tyres and Wheels Part 4: Rim Profiles and Dimensions Section 6: Motorcycle Rims Subsection 6.3: Specification for Code Designated Series (Diameter Codes 4 to 12) Rims (ISO 6054-2: 1990) |
|
BSI BS EN 12325-1 |
Irrigation Techniques - Centre Pivot and Moving Lateral Systems - Part 1: Presentation of the Technical Characteristics |
|
BSI BS EN 12502-5 |
Protection of metallic materials against corrosion Guidance on the assessment of corrosion likelihood in water distribution and storage systems Part 5: Influencing factors for cast iron, unalloyed and low alloyed steels |
|
BSI BS EN 12760 |
Valves - Socket Welding Ends for Steel Valves |
|
BSI BS EN 13395-1 |
Products and Systems for the Protection and Repair of Concrete Structures - Test Methods - Determination of Workability - Part 1: Test for Flow of Thixotropic Mortars |
|
BSI BS EN 13906-2 |
Cylindrical Helical Springs Made from Round Wire and Bar - Calculation and Design - Part 2: Extension Springs-Together with BS 1726-2: 2002, Supersedes BS 1726-2: 1988; |
|
BSI BS EN 14201 |
Blinds and shutters Resistance to repeated operations (mechanical endurance) Methods of testing |
|
BSI BS EN 14420-3 |
Hose fittings with clamp units - Part 3: Clamp units, bolted or pinned |
|
BSI BS EN 14430 |
Vitreous and porcelain enamels High voltage test |
|
BSI BS EN 1645-2 |
Leisure Accommodation Vehicles - Caravans - Part 2: User Payload |
|
BSI BS EN 1756-1 |
Tail Lifts - Platform Lifts for Mounting on Wheeled Vehicles - Safety Requirements - Part 1: Tail Lifts for Goods-Partially Supersedes BS 6109-1:1991; |
|
BSI BS EN 1986-2 |
Electrically Propelled Road Vehicles - Measurement of Energy Performances - Part 2: Thermal Electric Hybrid Vehicles |
|
BSI BS EN 27326 |
Rubber and Plastics Hoses - Assessment of Ozone Resistance Under Static Conditions (ISO 7326: 1991) (AMD 7526) August 15, 1993 (Formerly BS 5173: Section 106.3: 1991 Replaces BS 5173: Part 106: Section 106.3: 1986)-Amd 1; |
|
BSI BS EN 28601 |
Data Elements and Interchange Formats - Information Interchange - Representation of Dates and Times (ISO 8601: 1988) (AMD 7825) June 15, 1993 (Formerly BS 7151: 1989 Replaces BS 4760: 1971 and BS 5249: Part 1: 1976) (E) |
|
BSI BS EN 28749 |
Pins and Grooved Pins - Shear Test (ISO 8749: 1986) (E) |
|
BSI BS EN 299 |
Oil Pressure Atomizing Nozzles - Determination of the Angle and Spray Characteristics-Supersedes DD ENV 299: 1992; |
|
BSI BS EN 50294 |
Measurement Method of Total Input Power of Ballast-Lamp Circuits-AMD 14455: June 24, 2003; |
|
BSI BS EN 50428 |
Switches for household and similar fixed electrical installations Collateral standard Switches and related accessories for use in home and building electronic systems (HBES) |
|
BSI BS EN 60317-13 |
Specifications for Particular Types of Winding Wires Part 13: Polyester or Polyesterimide Overcoated with Polyamide-Imide Enamelled Round Copper Wire, Class 200-AMD 8888: November 1995; AMD 10306: May 1999; Renumbers BS 6811: Part 3: Section 3.3: 1989; IEC 60317-13:1990 |
|
BSI BS EN 60317-15 |
Specifications for particular types of winding wires Part 15: Polyesterimide enamelled round aluminium wire, class 180 |
|
BSI BS EN 60317-38 |
Particular Types of Winding Wires Part 38: Polyester or Polyesterimide Overcoated with Polyamide-Imide Enamelled Round Copper Wire, Class 200, with a Bonding Layer-AMD 10956: April 2001; IEC 60317-38: 1992; Renumbers BS 6811: Section 3.16: 1993; |
|
BSI BS EN 60317-39 |
Specifications for Particular Types of Winding Wires Part 39: Glass-Fibre Braided Resin or Varnish Impregnated, Bare or Enamelled Rectangular Copper Wire, Temperature Index 180-AMD 10335: July 1999; IEC 60317-39: 1992; Renumbers BS 6811: Section 7.1: 1993; |
|
BSI BS EN 60317-40 |
Specifications for particular types of winding wires Part 40: Glass-fibre braided resin or varnish impregnated, bare or enamelled rectangular copper wire, temperature index 200-AMD 8594: May 1995; AMD 10336: July 1999; AMD 16135: July 31, 2006; Renumbers BS 6811: Section 7.2: 1993 |
|
BSI BS EN 60317-48 |
Specifications for Particular Types of Windind Wires -Part 48: Glass-Fibre Wound Resin or Varnish Impregnated, Bare or Enamelled Round Copper Wire, Temperature Index 155-IEC 60317-48:1999; |
|
BSI BS EN 60360 |
Standard Method of Measurement of Lamp Cap Temperature Rise-Supersedes BS 5371: 1990; IEC 60360: 1998 |
|
BSI BS EN 60372 |
Locking devices for ball and socket couplings of string insulator units Dimensions and tests |
|
BSI BS EN 60432-1 |
Incandescent Lamps - Safety Specifications - Part 1: Tungsten Filament Lamps for Domestic and Similar General Lighting Purposes |
|
BSI BS EN 60641-3-1 |
Pressboard and Presspaper for Electrical Purposes Part 3: Specifications for Individual Materials Sheet 1. Requirements for Pressboard, Types B.0.1, B.2.1, B.2.3, B.3.1, B.3.3, B.4.1, B.4.3, B.5.1, B.6.1 and B.7.1-IEC 60641-3-1: 1992 |
|
BSI BS EN 60838-2-1 |
Miscellaneous Lampholders Part 2-1: Particular Requirements Section - Lampholders S14-AMD 10469: July 1999; AMD 15462: December 24, 2004; IEC 60838-2-1:1994 |
|
BSI BS EN 60852-4 |
Outline Dimensions of Transformers and Inductors for Use in Telecommunication and Electronic Equipment Part 4: Transformers and Inductors Using YUI-2 Laminations-IEC 852-4: 1996; |
|
BSI BS EN 61100 |
Classification of Insulating Liquids According to Fire Point and Net Calorific Value (IEC 1100: 1992) (E) |
|
BSI BS EN 61212-3-1 |
Insulating materials Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes Part 3: Specifications for individual materials Sheet 1: Round laminated rolled tubes |
|
BSI BS EN 61248-3 |
Transformers and Inductors for Use in Electronic and Telecommunication Equipment Part 3: Sectional Specification for Power Transformers on the Basis of the Capability Approval Procedure-IEC 61248-3: 1996; |
|
BSI BS EN 641 |
Reinforced Concrete Pressure Pipes, Cylinder Type, Including Joints and Fittings (Read in Conjunction with BS 639) (E) |
|
BSI BS EN ISO 10806 |
Pipework Fittings for corrugated metallic hoses-CORR 14987: January 30, 2004; |
|
BSI BS EN ISO 12209-3 |
Gas Cylinders - Outlet Connections for Gas Cylinder Valves for Compressed Breathable Air - Part 3: Adaptor for 230 Bar Valves-Partially Supersedes BS 341-2: 1963; |
|
BSI BS EN ISO 13340 |
Transportable Gas Cylinders - Cylinder Valves for Non-Refillable Cylinders - Specification and Prototype Testing-Partially Supersedes BS 341-1: 1991; |
|
BSI BS EN ISO 14589 |
Blind rivets Mechanical testing-CORR 15341:November 22, 2004; Together with BS EN ISO 14588:2001, BS EN ISO 15973:2000, BS EN ISO 15974:2001, BS EN ISO 15975:2002, BS EN ISO 15976:2002, BS EN ISO 15977:2002, BS EN ISO 15978:2002 and BS EN ISO 15979:2002 supersedes BS 7349-1:1993 |
|
BSI BS EN ISO 15008 |
Road vehicles Ergonomic aspects of transport information and control systems Specifications and compliance procedures for in-vehicle visual presentation-CORR 14613: August 11, 2003; |
|
BSI BS EN ISO 15983 |
Open end blind rivets with break pull mandrel and protruding head A2/A2-CORR 14321: January 28, 2003; CORR 15323: November 23, 2004; Together with BS EN ISO 15980:2002, BS EN ISO 15981:2002, BS EN ISO 15982:2002, BS EN ISO 15984:2002, BS EN ISO 16582:2002, BS EN ISO 16583:2002, BS EN ISO 16584:2002 and BS EN ISO 16585:2002, supersedes BS 7349-2:1993 |
|
BSI BS EN ISO 21670 |
Hexagon weld nuts with flange-CORR 14871: November 24, 2003; |
|
BSI BS EN ISO 8742 |
Grooved Pins - One-Third-Length Centre Grooved-Supersedes BS EN 28742: 1992 Which is Withdrawn; |
|
BSI BS ISO 10231 |
Motorcycle tyres Test methods for verifying tyre capabilities-Supersedes BS AU 50-1-6.6B: 1998; |
|
BSI BS ISO 10838-2 |
Mechanical Fittings for Polyethylene Piping Systems for the Supply of Gaseous Fuels - Part 2: Metal Fittings for Pipes of Nominal Outside Diameter Greater than 63mm |
|
BSI BS ISO 10946 |
Hydraulic Fluid Power - Gas-Loaded Accumulators with Separator - Selection of Preferred Hydraulic Ports |
|
BSI BS ISO 11565 |
Road vehicles  Spark-plugs  Test methods and requirements |
|
BSI BS ISO 12128 |
Plain Bearings - Lubrication Holes, Grooves and Pockets - Dimensions, Types, Designation and Their Application to Bearing Bushes |
|
BSI BS ISO 12238 |
Pneumatic Fluid Power - Directional Control Valves - Measurement of Shifting Time |
|
BSI BS ISO 13216-2 |
Road vehicles Anchorages in vehicles and attachments to anchorages for child restraint systems Part 2: Top tether anchorages and attachments |
|
BSI BS ISO 13476 |
Road Vehicles - Ignition Coils - Electrical Characteristics and Test Methods-AMD 10642; October 1999; |
|
BSI BS ISO 13674-2 |
Road vehicles Test method for the quantification of on-centre handling Part 2: Transition test |
|
BSI BS ISO 15242-2 |
Rolling bearings Measuring methods for vibration Part 2: Radial ball bearings with cylindrical bore and outside surface |
|
BSI BS ISO 15871 |
Industrial Trucks - Specification for Indicator Lights for Container Handling and Grappler Arm Operations |
|
BSI BS ISO 16132 |
Ductile iron pipes and fittings Seal coats for cement mortar linings-CORR 1:October 31, 2006;:2000 |
|
BSI BS ISO 17082 |
Pneumatic fluid power Valves Data to be included in supplier literature |
|
BSI BS ISO 22902-6 |
Road vehicles Automotive multimedia interface Part 6: Vehicle interface requirements |
|
BSI BS ISO 2344 |
Road Vehicles - M14 X 1,25 Spark Plugs with Conical Seating and Their Cylinder Head Housings |
|
BSI BS ISO 246 |
Rolling Bearings - Cylindrical Roller Bearings, Separate Thrust Collars - Boundary Dimensions (E) |
|
BSI BS ISO 2697 |
Diesel Engines - Fuel Nozzles - Size |
|
BSI BS ISO 4138 |
Passenger cars Steady-state circular driving behaviour Open-loop test methods-Supersedes BS AU 189:1983 |
|
BSI BS ISO 4141-2 |
Road vehicles Multi-core connecting cables Part 2: Test methods and requirements for high performance sheathed cables |
|
BSI BS ISO 7401 |
Road vehicles Lateral transient response test methods Open-loop test methods-Supersedes BS AU 230:1989; |
|
BSI BS ISO 7790 |
Hydraulic Fluid Power - Four-Port Modular Stack Valves and Four-Port Directional Control Valves, Sizes 02, 03 and 0,5 - Clamping Dimensions |
|
BSI BS ISO 7967-4 |
Reciprocating internal combustion engines Vocabulary of components and systems Part 4: Pressure charging and air/exhaust gas ducting systems-Supersedes BS 7016-4:1988; |
|
BSI BS ISO 8066-2 |
Rubber and Plastics Hoses and Hose Assemblies for Automotive Air Conditioning - Specification - Part 2: Refrigerant 134a |
|
BSI BS ISO 8085-1 |
Polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels - Metric series - Specifications - Part 1: Fittings for socket fusion using heated tools-CORR 13612: December 3, 2001; |
|
BSI BS ISO 8135 |
Hydraulic Fluid Power - Single Rod Cylinders, 16 MPa (160 Bar) Medium and 25 MPa (250 Bar) Series - Tolerances |
|
BSI BS ISO 9102 |
Diesel Engines - Screw-In Injection Nozzle Holders Types 24, 25, 26 and 26.1 |
|
BSI BS ISO 9393-1 |
Thermoplastics valves for industrial applications Pressure test methods and requirements Part 1: General |
|
BSI BS ISO 9815 |
Road vehicles Passenger-car and trailer combinations Lateral stability test-Supersedes BS AU 247:1993; |
|
BSI BS ISO 9912-1 |
Agricultural irrigation equipment Filters for micro-irrigation Part 1: Terms, definitions and classification |
|
BSI DD ISO/PAS 27145-3 |
Road vehicles Implementation of WWH-OBD communication requirements Part 3: Common message dictionary |
|
BSI DD ISO/TR 16144 |
Hydraulic fluid power Calibration of liquid automatic particle counters Procedures used to certify the standard reference material SRM 2806 |
|
BSI PD IEC/TR 60344 |
Calculation of d.c resistance of plain and coated copper conductors of low-frequency cables and wires  Application guide |
|
BSI PD ISO/TR 16806 |
Pneumatic fluid power Cylinders Load capacity of pneumatic slides and their presentation method |
|
BSI BS 1562-2 |
Agricultural Mower and Combine-Harvester Parts Part 2: Metric Units-BS 1562: Part 1: 1965; |
|
BSI BS 3777 |
Screw Thread Measuring Cylinders-Amd 1; |
|
BSI BS 4480 PART 5 |
Plain Bearings. Metric Series Part 5: Dimensions, Tolerances and Methods of Checking Thin-Walled Half Bearings |
|
BSI BS 4742 PART 8 |
Hydraulic Equipment for Agricultural Machinery Part 8: Method for Colour Coding of Remote Hydraulic Power Services and Controls on Agricultural Tractors |
|
BSI BS 4799 PART 1 |
(OBSOLESCENT)1972 Varnish-Bonded Glass- Lapped Copper Conductors Part 1: Round Wire |
|
BSI BS 4927 PART 1 |
(OBSOLESCENT)1974 Paper-, Cotton-, Silk- or Rayon-Covered Copper Conductors Part 1: Round Wire |
|
BSI BS 5173-103.6 |
Rubber and Plastics Hoses and Hose Assemblies Part 103: Physical Tests Section 103.6: Determination of Ignitability of Lining |
|
BSI BS 5246 |
Specification for Pinion type cutters for spur gears 1 to 8 metric module-AMD 2100: September 1976; Supersedes BS 2887: 1957 |
|
BSI BS 5341 SEC 7.4 |
Piston Rings up to 200 mm Diameter for Reciprocating Internal Combustion Engines Part 7: Designs, Dimensions and Designations for Single Piece Rings Section 7.4: Specification for Oil Control Rings (ISO 6625: 1986) |
|
BSI BS 5731 |
Mountings and Apertures for External Equipment Controls on Agricultural and Forestry Tractors (ISO 8935: 1990) |
|
BSI BS 5822 |
Agricultural Discs: Classification, Main Fixing Dimensions and General Requirements |
|
BSI BS 6010 PART 3 |
Rolling Bearings - Bearings with Spherical Outside Surface and Extended Inner Ring Width Part 3: Specification for Dimensions of Cast and Pressed Housings (ISO 3228: 1993) (E) |
|
BSI BS 6091 SEC 3.1 |
Vulcanized Fibre for Electrical Purposes Part 3: Specification for Individual Materials Section 3.1 Flat Sheets (Implementation of HD 416.3.1 S1 1988) (IEC 667-3-1: 1986) (E) |
|
BSI BS 6199 SEC 1.2 |
Measurement of Liquid Flow in Closed Conduits Using Weighing and Volumetric Methods Part 1: Weighing Method Section 1.2: Procedures for Checking Static Weighing Systems-ISO 9368-1: 1990; |
|
BSI BS 6483 PART 2 |
Fertilizer Distributors Part 2: Method of Test for Fertilizer Distributors in Lines |
|
BSI BS 6509 |
Clearance Zone on Implements for the Three-Point Linkage to Agricultural Tractors |
|
BSI BS 6537 |
Staple Type Connectors for Hydraulic Fluid Power Applications |
|
BSI BS 6550 |
Recommendation for Working Widths of Equipment for Sowing, Planting, Distributing Fertilizers and Spraying |
|
BSI BS 6818 PART 2 |
Front-Mounted Linkage and Power Take-off for Agricultural Wheeled Tractors Part 2: Front Linkage |
|
BSI BS 7016 PART 6 |
Components and Systems of Reciprocating Internal Combustion Engines Part 6: Glossary of Terms for Lubricating Systems (ISO 7967-6: 1992) |
|
BSI BS 7016 PART 9 |
Reciprocating Internal Combustion Engines - Vocabulary of Components and Systems Part 9: Control and Monitoring Systems-ISO 7967-9: 1996; |
|
BSI BS 7016-2 |
Components and Systems of Reciprocating Internal Combustion Engines - Part 2: Glossary of Terms for Main Running Gear-AMD 10890: February 2001; ISO 7967-2: 1987; |
|
BSI BS 7275 PART 3 |
Determination of Hydraulic Fluid Power Motor Characteristics Part 3: Method at Constant Flow and at Constant Torque (ISO 4392-3: 1993) (E) |
|
BSI BS 7293 |
Methods of Test for Equipment for Distributing Granulated Pesticides or Herbicides |
|
BSI BS 7433 PART 1 |
Cross Recessed Machine Screws Part 1: Specification for Pan Head Screws of Product Grade A (AMD 8514) March 15, 1995 (E)-Amd 1; |
|
BSI BS 7433 PART 3 |
Cross Recessed Machine Screws Part 3: Specification for Raised Countersunk Head Screws Product Grade A (AMD 8504) March 15, 1995 (E)-Amd 1; |
|
BSI BS 7560 |
Method of Assessing, Testing and Reporting Characteristics and Performance of Combine Harvesters (ISO 8210: 1989) |
|
BSI BS 7677 |
Classification of Imperfections in Pipe Joint Rings (ISO 9691: 1992) |
|
BSI BS 7791 |
Agricultural Tractors - Hydraulic Pressure for Implements (ISO 10448: 1994) (E) |
|
BSI BS 7795 |
Bolts, Screws and Studs with a Pre-Applied Micro-Encapsulated Chemical Adhesive Feature Incorporated into the Thread (E) |
|
BSI BS 7805 PART 1 |
Swaged Collar Grooved Rivets Part 1: Specification for Sizes up to and Including 10 mm Diameter (E) |
|
BSI BS AU 219 |
Dimensions of 40mm Drawbar Couplings Between Commercial Road Vehicles and Trailers |
|
BSI BS EN 12733 |
Agricultural and Forestry Machinery - Pedestrian Controlled Motor Mowers - Safety |
|
BSI BS EN 12965 |
Tractors and machinery for agriculture and forestry Power take-off (PTO) drive shafts and their guards Safety |
|
BSI BS EN 13153 |
Specification and Testing of LPG Cylinder Valves - Manually Operated-AMD 14541: July 18, 2003; |
|
BSI BS EN 13444-1 |
Electrically Propelled Road Vehicles - Measurement of Emissions of Hybrid Vehicles - Part 1: Thermal Electric Hybrid Vehicles |
|
BSI BS EN 13739-2 |
Agricultural machinery Solid fertilizer broadcasters and full width distributors Environmental protection Part 2: Test methods |
|
BSI BS EN 13740-1 |
Agricultural machinery Solid fertilizer line-distributors Environmental protection Part 1: Requirements |
|
BSI BS EN 13763-24 |
Explosives for civil uses Detonators and relays Part 24: Determination of the electrical non-conductivity of shock tube |
|
BSI BS EN 13787 |
Elastomers for Gas Pressure Regulators and Associated Safety Devices for Inlet Pressures Up to 100 Bar |
|
BSI BS EN 13790-1 |
Agricultural machinery Sprayers Inspection of sprayers in use Part 1: Field crop sprayers |
|
BSI BS EN 14419 |
District heating pipes Preinsulated bonded pipe systems for directly buried hot water networks Surveillance systems |
|
BSI BS EN 14483-1 |
Vitreous and porcelain enamels Determination of resistance to chemical corrosion Part 1: Determination of resistance to chemical corrosion by acids at room temperature-Supersedes BS 1344-2:1975 and BS EN ISO 8290:1998 |
|
BSI BS EN 14483-5 |
Vitreous and porcelain enamels Determination of resistance to chemical corrosion Part 5: Determination of resistance to chemical corrosion in closed systems-Supersedes BS ISO 13806:1999 |
|
BSI BS EN 60317-53 |
Specifications for Particular Types of Winding Wires - Part 53: Aromatic Polyamide (Aramid) Tape Wrapped Rectangular Copper Wire, Temperature Index 220-IEC 60317-53: 1999; |
|
BSI BS EN 60426 |
Electrical insulating materials  Determination of electrolytic corrosion caused by insulating materials  Test methods |
|
BSI BS EN 60455-3-2 |
Resin based reactive compounds used for electrical insulation Part 3: Specifications for individual materials Sheet 2: Quartz filled epoxy resinous compounds-Supersedes BS 5664-3.2: 1997; |
|
BSI BS EN 60512-11-12 |
Connectors for Electronic Equipment - Tests and Measurements - Part 11-12: Climatic Tests - Test 11m: Damp Heat, Cyclic |
|
BSI BS EN 60512-11-7 |
Connectors for electronic equipment Tests and measurements Part 11-7: Climatic tests Test 11g: Flowing mixed gas corrosion test |
|
BSI BS EN 60512-11-8 |
Electromechanical Components for Electronic Equipment - Basic Testing Procedures and Measuring Methods - Part 11: Climatic Tests - Section 8: Test 11h - Sand and Dust-IEC 60512-11-8: 1995; |
|
BSI BS EN 60512-11-9 |
Connectors for Electronic Equipment - Tests and Measurements - Part 11-9: Climatic Tests - Test 11i: Dry Heat |
|
BSI BS EN 60512-1-3 |
Electromechanical Components for Electronic Equipment - Basic Testing Procedures and Measuring Methods Part 1: General Examination Section 3: Test 1c: Electrical Engagement Length-IEC 60512-1-3: 1997: |
|
BSI BS EN 60512-14-7 |
Electromechanical Components for Electronic Equipment - Basic Testing Procedures and Measuring Methods Part 14: Sealing Tests Section 7: Test 14g: Impacting Water-IEC 60512-14-7: 1997; |
|
BSI BS EN 60512-19-3 |
Electromechanical Components for Electronic Equipment - Basic Testing Procedures and Measuring Methods Part 19: Chemical Resistance Tests Section 3: Test 19c. Fluid Resistance-IEC 60512-19-3: 1997; |
|
BSI BS EN 60512-25-1 |
Connectors for Electronic Equipment - Tests and Measurements - Part 25-1: Test 25a - Crosstalk Ratio-IEC 60512-25-1:2001; |
|
BSI BS EN 60512-25-3 |
Connectors for Electronic Equipment - Tests and Measurement - Part 25-3: Test 25c - Rise Time Degradation-IEC 60512-25-3:2001; |
|
BSI BS EN 60512-6-3 |
Connectors for Electronic Equipment - Tests and Measurements - Part 6-3: Dynamic Stress Tests - Test 6c: Shock |
|
BSI BS EN 60652 |
Loading tests on overhead line structures-AMD 15050: March 31, 2004; Renumbers BS IEC 60652:2002 |
|
BSI BS EN 60862-2 |
Surface acoustic wave (SAW) filters of assessed quality Part 2: Guidance on use |
|
BSI BS EN 61040 |
Power and Energy Measuring Detectors, Instruments and Equipment for Laser Radiation (IEC 1040: 1990) (E) |
|
BSI BS EN 61143-2 |
Electrical Measuring Instruments - X-t Recorders Part 2: Recommended Additional Test Methods-AMD 8389; January 15, 1995; Renumbers BS 7610 Part 2:1993 |
|
BSI BS EN 61235 |
Live working Insulating hollow tubes for electrical purposes-CORR 13835:December 23, 2002; |
|
BSI BS EN 61236 |
Saddles, Pole Clamps (Stick Clamps) and Accessories for Live Working-CORR 13871: October 4, 2002 |
|
BSI BS EN 61629-1 |
Aramid Pressboard for Electrical Purposes Part 1: Definitions, Designations and General Requirements-IEC 1629-1:1996 |
|
BSI BS EN 61788-9 |
Superconductivity Part 9: Measurements for bulk high temperature superconductors Trapped flux density of large grain oxide superconductors |
|
BSI BS EN 61969-1 |
Mechanical Structures for Electronic Equipment - Outdoor Enclosures - Part 1: Design Guidelines-IEC 61969-1: 1999; |
|
BSI BS EN 62011-2 |
Insulating materials Industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross-section, based on thermosetting resins for electrical purposes Part 2: Methods of test |
|
BSI BS EN 62011-3-1 |
Insulating materials Industrial rigid moulded laminated tubes and rods of rectangular and hexagonal cross-section based on thermosetting resins for electrical purposes Part 3-1: Specifications for individual materials Tubes and rods of rectangular and hexagonal cross-section |
|
BSI BS EN 62013-1 |
Caplights for use in mines susceptible to firedamp Part 1: General requirements Construction and testing in relation to the risk of explosion |
|
BSI BS EN 62013-2 |
Caplights for use in mines susceptible to firedamp Part 2: Performance and other safety-related matters-Supersedes BS 4945: 1989; IEC 62013-2: 2000; |
|
BSI BS EN 62044-1 |
Cores made of soft magnetic materials - Measuring methods - Part 1: Generic specification |
|
BSI BS EN 62044-3 |
Cores Made of Soft Magnetic Materials - Measuring Methods - Part 3: Magnetic Properties at High Excitation Level |
|
BSI BS EN 62333-1 |
Noise suppression sheet for digital devices and equipment Part 1: Definitions and general properties |
|
BSI BS EN 62333-2 |
Noise suppression sheet for digital devices and equipment Part 2: Measuring methods |
|
BSI BS EN 629-1 |
Transportable Gas Cylinders - 25E Taper Thread for Connection of Valves to Gas Cylinders Part 1: Specification |
|
BSI BS EN 720-2 |
Transportable Gas Cylinders - Gases and Gas Mixtures Part 2: Determination of Flammability and Oxidizing Ability of Gases and Gas Mixtures |
|
BSI BS EN ISO 10484 |
Widening test on nuts-AMD 15307: August 11, 2004; Renumbers BS ISO 10484 |
|
BSI BS EN ISO 10485 |
Cone proof load test on nuts-Supersedes BS 7597:1992 |
|
BSI BS EN ISO 15106-1 |
Plastics Film and sheeting Determination of water vapour transmission rate Part 1: Humidity detection sensor method |
|
BSI BS EN ISO 15106-2 |
Plastics Film and sheeting Determination of water vapour transmission rate Part 2: Infrared detection sensor method |
|
BSI BS EN ISO 15975 |
Closed end blind rivets with break pull mandrel and protruding head AI/AIA-CORR 14324: February 3, 2003; CORR 15344: November 24, 2004; Together with BS EN ISO 14588:2001, BS EN ISO 14589:2001, BS EN ISO 15973:2000, BS EN ISO 15974:2001, BS EN ISO 15976:2002, BS EN ISO 15977:2002, BS EN ISO 15978:2002 and BS EN ISO 15979:2002 supersedes BS 7349-1:1993 |
|
BSI BS EN ISO 15981 |
Open end blind rivets with break pull mandrel and protruding head AIA/AIA-CORR 14323: January 23, 2003; CORR 15349: November 23, 2004; Together with BS EN ISO 15980:2002, BS EN ISO 15982:2002, BS EN ISO 15983:2002, BS EN ISO 15984:2002, BS EN ISO 16582:2002, BS EN ISO 16583:2002, BS EN ISO 16584:2002 and BS EN ISO 16585:2002, supersedes BS 7349-2:1993 |
|
BSI BS EN ISO 16582 |
Open end blind rivets with break pull mandrel and protruding head Cu/St or Cu/Br or Cu/SSt-CORR 14311: January 24, 2003; CORR 15325: November 23, 2004; Together with BS EN ISO 15980:2002, BS EN ISO 15981:2002, BS EN ISO 15982:2002, BS EN ISO 15983:2002, BS EN ISO 15984:2002, BS EN ISO 16583:2002, BS EN ISO 16584:2002 and BS EN ISO 16585:2002, supersedes BS 7349-2:1993 |
|
BSI BS EN ISO 6224 |
Plastics Hoses, Textile-Reinforced, for General-Purpose Water Applications - Specification-AMD 9706: 12/1997; Renumbers BS ISO 6224:1996 |
|
BSI BS EN ISO 6806 |
Rubber Hoses and Hose Assemblies for Use in Oil Burners - Specification (E) |
|
BSI BS EN ISO 7051 |
Cross-Recessed Raised Countersunk (Oval) Head Tapping Screws (E) |
|
BSI BS EN ISO 8308 |
Rubber and Plastics Hoses and Tubing - Determination of Transmission of Liquids Through Hose and Tubing Walls (E) |
|
BSI BS EN ISO 8580 |
Rubber and Plastics Hoses - Determination of Ultra-Violet Resistance Under Static Conditions (AMD 8665) July 15, 1995 (Formerly BS 5173: Part 106: Sec 106.4: 1989 Replaces BS 5173: Pt 6: 1977) (E)-Amd 1; |
|
BSI BS ISO 11486 |
Motorcycles Methods for setting running resistance on a chassis dynamometer |
|
BSI BS ISO 11992-4 |
Road vehicles Interchange of digital information on electrical connections between towing and towed vehicles Part 4: Diagnostics-CORR 16469: August 2006 |
|
BSI BS ISO 12161 |
Road vehicles Endurance braking systems of motor vehicles and towed vehicles Test procedures |
|
BSI BS ISO 12307-2 |
Plain Bearings - Checking of Wrapped Bushes - Part 2: Checking the Insider Diameter |
|
BSI BS ISO 13726 |
Hydraulic Fluid Power - Single Rod Cylinders, 16 MPa (160 Bar) Compact Series with Bores from 250 mm to 500 mm - Accessory Mounting Dimensions |
|
BSI BS ISO 14269-4 |
Tractors and Self-Propelled Machines for Agriculture and Forestry - Operator Enclosure Environment - Part 4: Air Filter Element Test Method |
|
BSI BS ISO 14269-5 |
Tractors and Self-Propelled Machines for Agriculture and Forestry - Operator Enclosure Environment - Part 5: Pressurization System Test Method |
|
BSI BS ISO 14740 |
Forestry Machinery - Backpack Power Units for Brush Cutters, Grass Trimmers, Pole Cutters and Similar Appliances - Safety Requirements and Testing |
|
BSI BS ISO 14743 |
Pneumatic fluid power Push-in connectors for thermoplastic tubes |
|
BSI BS ISO 14794 |
Heavy commercial vehicles and buses Braking in a turn Open-loop test methods |
|
BSI BS ISO 16232-10 |
Road vehicles  Cleanliness of components of fluid circuits  Part 10: Expression of results |
|
BSI BS ISO 16232-3 |
Road vehicles  Cleanliness of components of fluid circuits  Part 3: Method of extraction of contaminants by pressure rinsing |
|
BSI BS ISO 16232-7 |
Road vehicles  Cleanliness of components of fluid circuits  Part 7: Particle sizing and counting by microscopic analysis |
|
BSI BS ISO 16246 |
Road vehicles M12 x 1,25 spark-plugs with flat seating and 14 mm hexagon and their cylinder head housing |
|
BSI BS ISO 16589-4 |
Rotary Shaft Lip-Type Seals Incorporating Thermoplastic Sealing Elements - Part 4: Performance Test Procedures |
|
BSI BS ISO 16589-5 |
Rotary Shaft Lip-Type Seals Incorporating Thermoplastic Sealing Elements - Part 5: Identification of Visual Imperfections |
|
BSI BS ISO 17268 |
Compressed hydrogen surface vehicle refuelling connection devices |
|
BSI BS ISO 17554 |
Reaction to fire tests  Mass loss measurement |
|
BSI BS ISO 19013-2 |
Rubber hoses and tubing for fuel circuits for internal combustion engines Specification Part 2: Gasoline fuels-CORR 16186: March 2006; Together with BS ISO 19013-1 supersedes BS ISO 4639-2:1995 and BS ISO 4639-3:1995 |
|
BSI BS ISO 20828 |
Road vehicles Security certificate management |
|
BSI BS ISO 21308-2 |
Road vehicles Product data exchange between chassis and bodywork manufacturers (BEP) Part 2 : Dimensional bodywork exchange parameters |
|
BSI BS ISO 22368-3 |
Crop protection equipment Test methods for the evaluation of cleaning systems Part 3: Internal cleaning of tank |
|
BSI BS ISO 22877 |
Castors and wheels Vocabulary, symbols and multilingual terminology |
|
BSI BS ISO 3031 |
Rolling Bearings - Thrust Needle Roller and Cage Assemblies, Thrust Washer - Boundary Dimensions and Tolerances-Supersedes BS 5773: Part 4: 1980 |
|
BSI BS ISO 3245 |
Rolling Bearings - Needle Roller Bearings, Drawn Cup without Inner Rings - Boundary Dimensions and Tolerances-Supersedes BS 5773: Part 2: 1979; |
|
BSI BS ISO 3547-2 |
Plain bearings Wrapped bushes Part 2: Test data for outside and inside diameters |
|
BSI BS ISO 3548 |
Plain Bearings - Thin-Walled Half Bearings with or without Flange - Tolerances, Design Features and Methods of Test |
|
BSI BS ISO 3767-2 |
Tractors, machinery for agriculture and forestry, powered lawn and garden equipment Symbols for operator controls and other displays Part 2: Symbols for agricultural tractors and machinery-AMD 14695: November 13, 2003; Renumbers BS EN ISO 3767-2:1996; |
|
BSI BS ISO 3767-3 |
Tractors, machinery for agriculture and forestry, powered lawn and garden equipment Symbols for operator controls and other displays Part 3: Symbols for powered lawn and garden equipment-AMD 14696: October 15, 2003; Renumbers BS EN ISO 3767-3:1996; |
|
BSI BS ISO 3888-2 |
Passenger cars Test track for a severe lane-change manoeuvre Part 2: Obstacle avoidance |
|
BSI BS ISO 4250-3 |
Earth-mover tyres and rims Part 3: Rims-: 1998 |
|
BSI BS ISO 500-1 |
Agricultural tractors Rear-mounted power take-off types 1, 2 and 3 Part 1: General specifications, safety requirements, dimensons for master shield and clearance zone-Together with BS ISO 500-2:2006 and BS ISO 500-3:2006 supersedes BS 5861:1992 |
|
BSI BS ISO 6531 |
Machinery for Forestry - Portable Hand-Held Chain-Saws - Vocabulary-Supersedes BS 6916-1:1988; |
|
BSI BS ISO 6623 |
Internal combustion engines Piston rings Scraper rings made of cast iron-Supersedes BS 5341-7.2:1992 |
|
BSI BS ISO 6624-2 |
Internal combustion engines Piston rings Part 2: Half keystone rings made of cast iron |
|
BSI BS ISO 7026 |
Diesel Engines - Screw-In Injection Nozzle Holders, Types 20, 21, 21.1 and 27 for Pintle Nozzle Size `S1' Type `B' |
|
BSI BS ISO 7967-5 |
Reciprocating internal combustion engines Vocabulary of components and systems Part 5: Cooling systems-Supersedes BS 7016-5:1992; |
|
BSI BS ISO 8349 |
Road Vehicles - Measurement of Road Surface Friction |
|
BSI BS ISO 8820-5 |
Road vehicles  Fuse-links  Part 5: Fuse-links with axial terminals (Strip fuse-links) Types SF 30 and SF 51 and test fixtures |
|
BSI BS ISO 9518 |
Forestry Machinery - Portable Chain-Saws - Kickback Test |
|
BSI BS ISO 9631 |
Rubber seals Joint rings for pipelines for hot-water supply, drainage and sewerage up to 110 °C Specification for the material |
|
BSI BS ISO 9816 |
Passenger cars  Power-off reaction of a vehicle in a turn  Open-loop test method |
|
BSI BS ISO/TR 14179-1 |
Gears - Thermal Capacity - Part 1: Rating Gear Drives with Thermal Equilibrium at 95 Degrees C Sump Temperature |
|
BSI DD 208 |
Piston Rings up to 200 mm Diameter for Reciprocating Internal Combustion Engines: Specification for Rectangular Rings with Narrow Ring Width (ISO/TR 6622-2: 1988) (E) |
|
BSI DD CEN/TS 15213-2 |
Road transport and traffic telematics After-theft systems for the recovery of stolen vehicles Part 2: Common status message elements |
|
BSI PAS 62 |
Refrigerated transport Procedure for determining performance and calculating energy efficiency |
|
BSI PD 6487 |
Calculating the Life of Ball Bearings When Used in Contact with Fire Resistant Hydraulic Fluids |
|
BSI PD IEC/TR 61946 |
Mineral insulating oils  Characterization of paraffinic/naphthenic nature  Low temperature differential scanning calorimetry (DSC) test method |
|
BSI PD IEC/TR 62154 |
Terminology in the area of information structures, documentation and graphical symbols |
|
BSI PD ISO/TR 17452 |
Intelligent transport systems  Using UML for defining and documenting ITS/TICS interfaces |
|
BSI BS 1103 |
Specification for Fabrics for the reinforcement of rubber hoses |
|
BSI BS 1717 |
Steel Tubes for Cycle and Motor-Cycle Purposes |
|
BSI BS 3486 PART 1 |
Wheels for Tractors and Machinery for Agriculture and Forestry Part 1: Specification for Wheel-to-Hub Fixing Dimensions (ISO 5711: 1995) (E) |
|
BSI BS 4110 |
Visors for Vehicle Users |
|
BSI BS 4151 |
Method of Evaluating Pneumatic Valve Positioners with 3 to 15 LBF/in 2 (Gauge) Input Signal |
|
BSI BS 4161 PART 2 |
Gas Meters Part 2: Meters of Plate Construction Above 1000 Cubic Feet (28 Cubic Meters) per Hour Rating-Amd 2; |
|
BSI BS 4480 PART 8 |
Plain Bearings. Metric Series Part 8: Dimensions, Tolerances and Methods of Checking of Thin- Walled Flanged Half Bearings |
|
BSI BS 4480 PART 9 |
Plain Bearings: Metric Series Part 9: Checking the Outside Diameter of Wrapped Bushes-ISO 12307-1: 1994 |
|
BSI BS 4639 |
Brakes and Braking Systems for Towed Agricultural Vehicles |
|
BSI BS 4742 PART 2 |
Hydraulic Equipment for Agricultural Machinery Part 2: Specification for Quick-Action Hydraulic Couplers for General Purposes (ISO 5675: 1992) (E) |
|
BSI BS 4742 PART 5 |
Hydraulic Equipment for Agricultural Machinery Part 5: Dimensions of Braking Cylinders for Trailers and Trailed Equipment |
|
BSI BS 5173-106.2 |
Methods of Test for Rubber and Plastics Hoses and Hose Assemblies Part 106: Environmental Tests Section 106.2: General Requirements for High Temperature Ageing Tests (E) |
|
BSI BS 5209 |
Testing of Sulphur Hexafluoride Taken from Electrical Equipment-Partially superseded by BS EN 60480: 2005 |
|
BSI BS 5341 PART 5 |
Piston Rings up to 200 mm Diameter for Reciprocating Internal Combustion Engines Part 5: Ring Grooves |
|
BSI BS 5341 SEC 6.1 |
Piston Rings up to 200 mm Diameter for Reciprocating Internal Combustion Engines Part 6: Vocabulary, Inspection Methods and Generic Specifications Section 6.1: Vocabulary (ISO 6621-1: 1986) |
|
BSI BS 5341 SEC 8.1 |
Piston Rings up to 200 mm Diameter for Reciprocating Internal Combustion Engines Part 8: Designs, Dimensions and Designations for Multi- Piece Oil Control Rings Sec 8.1: Specification for Coil-Spring-Loaded Oil Control Rings (ISO 6626: 1989) |
|
BSI BS 5510 |
Determination of Maximum Speeds of Agricultural Wheeled Tractors-ISO 3965: 1990 |
|
BSI BS 5626 SEC 3.2 |
Cellulosic Papers for Electrical Purposes Part 3: Specifications for Individual Materials Section 3.2: Capacitor Paper |
|
BSI BS 5626 SEC 3.5 |
Cellulosic Papers for Electrical Purposes Part 3: Specifications for Individual Materials Section 3.5: Special Papers (IEC 554-3-5: 1984) (E) |
|
BSI BS 5664 SEC 3.11 |
Solventless Polymerisable Resinous Compounds Used for ELectrical Insulation Part 3: Specifications for Individual Materials Section 3.11: Epoxy Resin-Based Coating Powders (IEC 455-3-11:1988) (E) |
|
BSI BS 5672 |
Designation of the Direction of Rotation and of Cylinders and Valves in Cylinder Heads, and Definition of Right-Hand and Left-Hand in-Line Engines and Locations on an Engine for Reciprocating Internal Combustion Engines (ISO 1204: 1990) |
|
BSI BS 5689 PART 1 |
Varnished Fabrics for Electrical Purposes Part 1: Definitions and General Requirements |
|
BSI BS 5689 PART 2 |
Varnished Fabrics for Electrical Purposes Part 2: Methods of Test |
|
BSI BS 6074 |
Determination of the Volumetric Rating of Tractor-Scrapers for Earth-Moving Machinery |
|
BSI BS 6142 |
Presentation of Technical Data on Hydraulic Systems of Agricultural Tractors and Machinery |
|
BSI BS 6448 |
Gas Appliance Governors of DN Greater than 50 and for Inlet Pressures up to 200 Mbar (E) |
|
BSI BS 6490 |
Shapes and Dimensions (Excluding Thread Dimensions) of Plough Bolt Heads for Earth- Moving Machinery |
|
BSI BS 6735 |
Reach Volumes for the Location of Controls on Agricultural Tractors and Machinery |
|
BSI BS 6978 PART 1 |
Seed Drills Part 1: Methods of Test for Single Seed Drills |
|
BSI BS 6978 PART 2 |
Seed Drills Part 2: Methods of Test for Seed Drills for Rows |
|
BSI BS 7016 PART 3 |
Components and Systems of Reciprocating Internal Combustion Engines Part 3: Glossary of Terms of Valves, Camshaft Drive and Actuating Mechanisms |
|
BSI BS 7403 PART 3 |
Full-Flow Lubricating Oil Filters for Internal Combustion Engines Part 3: Methods of Test for Resistance to High Differential Pressure and to Elevated Temperature-BS 7403: Part 3, Together with BS 7403: Parts 1,2 and 4 Supersedes BS 4836: 1972; ISO 4548-3: 1997; |
|
BSI BS 7403 PART 7 |
Full-Flow Lubricating Oil Filters for Internal Combustion Engines Part 7: Method of Test for Vibration Fatigue (ISO 4548-7: 1990) |
|
BSI BS 7484 |
Electromagnetic Environment for Low-Frequency Conducted Disturbances and Signalling in Public Power Supply Systems (IEC 1000-2-1: 1990) |
|
BSI BS 7675 |
Plain Bearings - Thin-Walled Half Bearings - Checking of Peripheral Length (ISO 6524: 1992) (E) |
|
BSI BS 7805 PART 2 |
Swaged Collar Grooved Rivets Part 2: Specification for Sizes from 12.7 mm up to and Including 34.9 mm |
|
BSI BS 7848 |
Gears - Wear and Damage to Gear Teeth - Terminology |
|
BSI BS AU 224B |
Portable Wheel Ramps for Cars and Light Vans-Supersedes BS AU 224a: 1988 |
|
BSI BS EN 10342 |
Magnetic materials Classification of surface insulations of electrical steel sheet, strip and laminations |
|
BSI BS EN 1053 |
Plastics Piping Systems - Thermoplastics Piping Systems for Non-Pressure Applications - Test Method for Watertightness (E) |
|
BSI BS EN 12601 |
Reciprocating Internal Combustion Engine Driven Generating Sets - Safety |
|
BSI BS EN 12761-2 |
Agricultural and Forestry Machinery - Sprayers and Liquid Fertilizer Distributors - Environmental Protection - Part 2: Field Crop Sprayers |
|
BSI BS EN 12761-3 |
Agricultural and Forestry Machinery - Sprayers and Liquid Fertilizer Distributors - Environmental Protection - Part 3: Air-Assisted Sprayers for Bush and Tree Crops |
|
BSI BS EN 12842 |
Ductile Iron Fittings for PVC-U or PE Piping Systems - Requirements and Test Methods |
|
BSI BS EN 13080 |
Agricultural machinery Manure spreaders Environmental protection Requirements and test methods |
|
BSI BS EN 13447 |
Electrically Propelled Road Vehicles - Terminology |
|
BSI BS EN 13807 |
Transportable gas cylinders Battery vehicles Design, manufacture, identification and testing-CORR 15910: January 18, 2006 |
|
BSI BS EN 13951 |
Liquid pumps Safety requirements Agrifoodstuffs equipment; Design rules to ensure hygiene in use |
|
BSI BS EN 14483-2 |
Vitreous and porcelain enamels Determination of resistance to chemical corrosion Part 2: Determination of resistance to chemical corrosion by boiling acids, neutral liquids and/or their vapours-Supersedes BS 1344-8:1984, BS 1344-9:1998, BS 1344-10:1987 and BS 1344-14:1984 |
|
BSI BS EN 14483-3 |
Vitreous and porcelain enamels Determination of resistance to chemical corrosion Part 3: Determination of resistance to chemical corrosion by alkaline liquids using a hexagonal vessel-Supersedes BS 1344-5:1984 and BS EN ISO 4535:2000 |
|
BSI BS EN 14571 |
Metallic coatings on nonmetallic basis materials Measurement of coating thickness Microresistivity method |
|
BSI BS EN 14628 |
Ductile iron pipes, fittings and accessories External polyethylene coating for pipes Requirements and test methods |
|
BSI BS EN 26801 |
Rubber and Plastics Hoses - Determination of Volumetric Expansion-AMD 7520; April 15, 1993; Formerly BS 5173: Section 102.2: 1985 |
|
BSI BS EN 50148 |
Electronic Taximeters (E) |
|
BSI BS EN 50363-10-2 |
Insulating, sheathing and covering materials for low voltage energy cables Part 10-2: Miscellaneous sheathing compounds Thermoplastic polyurethane-Supersedes BS 7655-12.1: 2000 |
|
BSI BS EN 50363-4-1 |
Insulating, sheathing and covering materials for low voltage energy cables Part 4-1: PVC sheathing compounds-:1997 |
|
BSI BS EN 50363-4-2 |
Insulating, sheathing and covering materials for low voltage energy cables Part 4-2: PVC covering compounds |
|
BSI BS EN 50369 |
Liquid tight sheathing systems for cable management |
|
BSI BS EN 50414 |
Test methods for analysis of lead in PVC taken from insulation and sheath of electric and optical fibre cables Method A: Total lead content determination with flame excitation atomic absorption spectrometry Method B: Qualitative analysis of lead by lead sulphide staining |
|
BSI BS EN 60455-3-1 |
Resin based reactive compounds used for electrical insulation Part 3: Specifications for individual materials Sheet 1: Unfilled epoxy resinous compounds-Supersedes BS 5664-3.1: 1995; |
|
BSI BS EN 60512-11-10 |
Connectors for Electronic Equipment - Tests and Measurements - Part 11-10: Climatic Tests - Test 11j: Cold |
|
BSI BS EN 60512-11-13 |
Connectors for Electronic Equipment - Tests and Measurements - Part 11-13: Climatic Tests - Test 11n: Gas Tightness, Solderless Wrapped Connections-IEC 60512-11-13: 2002; |
|
BSI BS EN 60512-11-3 |
Connectors for Electronic Equipment - Tests and Measurements - Part 11-3: Climatic Tests - Test 11c: Damp Heat, Steady State |
|
BSI BS EN 60512-25-2 |
Connectors for Electronic Equipment - Tests and Measurements - Part 25-2: Test 25b: Attenuation (Insertion Loss) |
|
BSI BS EN 60512-4-3 |
Connectors for Electronic Equipment - Tests and Measurements - Part 4-3: Voltage Stress Tests - Test 4c: Voltage Proof of Pre-Insulted Crimp Barrels |
|
BSI BS EN 60856 |
Pre-Recorded Optical Reflective Videodisk System 'Laser Vision' 50 Hz/625 Lines - PAL-AMD 9795; January 1998; Supersedes BS 6895: 1987; IEC 856: 1986; |
|
BSI BS EN 61175 |
Industrial systems, installations and equipment and industrial products Designation of signals |
|
BSI BS EN 61360-2 |
Standard Data Element Types with Associated Classification Scheme for Electric Components - Part 2: EXPRESS Dictionary Schema-AMD 15574: May 13, 2005; IEC 61360-2: 2002 |
|
BSI BS EN 61609 |
Microwave Ferrite Components - Guide for the Drafting of Specifications-IEC 61609: 1996; |
|
BSI BS EN 61629-2 |
Aramid Pressboard for Electrical Purposes Part 2: Methods of Test-IEC 1629-2:1996 |
|
BSI BS EN 61631 |
Test Method for the Mechanical Strength of Cores Made of Magnetic Oxides-IEC 61631:2001; |
|
BSI BS EN 61788-10 |
Superconductivity Part 10: Critical temperature measurement Critical temperature of composite superconductors by a resistance method |