|
BSI BS EN 61788-8 |
Superconductivity Part 8: AC loss measurements Total AC loss measurement of Cu/Nb-Ti composite superconducting wires exposed to a transverse alternating magnetic field by a pickup coil method |
|
BSI BS EN 61969-2 |
Mechanical Structures for Electronic Equipment - Outdoor Enclosures - Part 2: Sectional Specification - Coordination Dimensions for Cases and Cabinets-IEC 61969-2: 2000; |
|
BSI BS EN 62025-2 |
High frequency inductive components Non-electrical characteristics and measuring methods Part 2: Test methods for non-electrical characteristics |
|
BSI BS EN 62094-1 |
Indicator light units for household and similar fixed-electrical installations Part 1: General requirements-AMD 15550:February 25, 2005 |
|
BSI BS EN 62217 |
Polymeric insulators for indoor and outdoor use with a nominal voltage > 1 000 V General definitions, test methods and acceptance criteria-CORR 16923: February 28, 2007 |
|
BSI BS EN 62323 |
Dimensions of half pot-cores made of ferrite for inductive proximity switches |
|
BSI BS EN 690 |
Agricultural Machinery - Manure Spreaders - Safety (E) |
|
BSI BS EN 704 |
Agricultural Machinery - Pick-Up Balers - Safety |
|
BSI BS EN 721 |
Leisure accommodation vehicles Safety ventilation requirements |
|
BSI BS EN 745 |
Agricultural Machinery - Rotary Mowers and Flail-Mowers - Safety |
|
BSI BS EN ISO 11680-1 |
Machinery for Forestry - Safety Requirements and Testing Pole-Mounted Powered Pruners - Part 1: Units Fitted with an Integral Combustion Engine-CORR 14047: February 5, 2003; |
|
BSI BS EN ISO 13341 |
Transportable Gas Cylinders - Fitting of Valves to Gas Cylinders |
|
BSI BS EN ISO 1483 |
Slotted Raised Countersunk (Oval) Head Tapping Screws (Common Head Style) (E) |
|
BSI BS EN ISO 15980 |
Open end blind rivets with break pull mandrel and Countersunk head St/St-CORR 14322: January 22, 2003; CORR 15348: November 23, 2004 Together with BS EN ISO 15981:2002, BS EN ISO 15982:2002, BS EN ISO 15981:2002, BS EN ISO 15983:2002, BS EN ISO 15984:2002, BS EN ISO 16582:2002, BS EN ISO 16583:2002, BS EN ISO 16584:2002 and BS EN ISO 16585:2002, supersedes BS 7349-2:1993 |
|
BSI BS EN ISO 16583 |
Open end blind rivets with break pull mandrel and countersunk head Cu/St or Cu/Br or Cu/SSt-CORR 14312: January 24, 2003; CORR 15326: November 23, 2004; Together with BS EN ISO 15980:2002, BS EN ISO 15981:2002, BS EN ISO 15982:2002, BS EN ISO 15983:2002, BS EN ISO 15984:2002, BS EN ISO 16582:2002, BS EN ISO 16584:2002 and BS EN ISO 16585:2002; Supersedes BS 7349-2:1993 |
|
BSI BS EN ISO 21007-1 |
Gas cylinders Identification and marking using radio frequency identification technology Part 1: Reference architecture and terminology |
|
BSI BS EN ISO 8092-4 |
Road Vehicles - Connections for On-Board Electrical Wiring Harnesses - Part 4: Pins for Single- and Multi-Pole Connections - Dimensions and Specific Requirements (ISO 8092-4: 1997) |
|
BSI BS EN ISO 8751 |
Spring-Type Straight Pins - Coiled, Light Duty-Supersedes BS EN 28751: 1992; |
|
BSI BS ISO 10054 |
Internal Combustion Compression-Ignition Engines - Measurement Apparatus for Smoke from Engines Operating under Steady-State Conditions - Filter Type Smokemeter |
|
BSI BS ISO 10300-3 |
Calculation of Load Capacity of Bevel Gears - Part 3: Calculation of Tooth Root Strength |
|
BSI BS ISO 10663 |
Hexagon Nuts with Flange - Fine Pitch Thread |
|
BSI BS ISO 11237-1 |
Rubber hoses and hose assemblies Wire-braid-reinforced compact types for hydraulic applications Specification Part 1: Oil-based fluid applications |
|
BSI BS ISO 11237-2 |
Rubber hoses and hose assemblies Wire-braid-reinforced compact types for hydraulic applications Specification Part 2: Water-based fluid applications |
|
BSI BS ISO 11783-3 |
Tractors and Machinery for Agriculture and Forestry - Serial Control and Communications Data Network - Part 3: Data Link Layer |
|
BSI BS ISO 11786 |
Agricultural Tractors and Machinery - Tractor Mounted Sensor Interface - Specification (E) |
|
BSI BS ISO 12043 |
Rolling Bearings - Single-Row Cylindrical Roller Bearings - Chamfer Dimensions for Loose Rib and Non-Rib Sides (E) |
|
BSI BS ISO 12097-1 |
Road vehicles Airbag components Part 1: Vocabulary |
|
BSI BS ISO 12140 |
Agricultural Machinery - Agricultural Trailers and Trailed Equipment - Drawbar Jacks-Supersedes BS 6792: 1986; |
|
BSI BS ISO 13555-3 |
Diesel engines Procedure for checking the dynamic timing of diesel fuel injection equipment Part 3: Validation of timing measurement devices |
|
BSI BS ISO 13772 |
Forestry Machinery - Portable Chainsaws - Non-Manually Actuated Chain Brake Performance |
|
BSI BS ISO 14269-1 |
Tractors and Self-Propelled Machines for Agriculture and Forestry - Operator Enclosure Environment - Part 1: Vocabulary |
|
BSI BS ISO 14269-2 |
Tractors and Self-Propelled Machines for Agriculture and Forestry - Operator Enclosure Environment - Part 2: Heating, Ventilating and Air-Conditioning Test Method and Performance |
|
BSI BS ISO 14269-3 |
Tractors and Self-Propelled Machines for Agriculture and Forestry - Operator Enclosure Environment - Part 3: Determination of Effect of Solar Heating |
|
BSI BS ISO 14681 |
Diesel Engines - Fuel Injection Pump Testing - Calibrating Fuel Injectors |
|
BSI BS ISO 14728-2 |
Rolling bearings Linear motion rolling bearings Part 2: Static load ratings |
|
BSI BS ISO 15064 |
Plastics Aromatic isocyanates for use in the production of polyurethanes Determination of the isomer ratio in toluenediisocyanate |
|
BSI BS ISO 16232-4 |
Road vehicles  Cleanliness of components of fluid circuits  Part 4: Method of extraction of contaminants by ultrasonic techniques |
|
BSI BS ISO 16232-5 |
Road vehicles  Cleanliness of components of fluid circuits  Part 5: Method of extraction of contaminants on functional test bench |
|
BSI BS ISO 16750-1 |
Road vehicles  Environmental conditions and testing for electrical and electronic equipment  Part 1: General |
|
BSI BS ISO 16992 |
Passenger car tyres Spare unit substitutive equipment (SUSE) |
|
BSI BS ISO 17288-1 |
Passenger cars Free-steer behaviour Part 1: Steering-release open-loop test method |
|
BSI BS ISO 17288-2 |
Passenger cars Free-steer behaviour Part 2: Steering-pulse open-loop test method |
|
BSI BS ISO 17356-6 |
Road vehicles Open interface for embedded automotive applications Part 6: OSEK/VDX Implementation Language (OIL) |
|
BSI BS ISO 17900 |
Agricultural Trailers - Balanced and Semi-Mounted Trailers - Determination of Payload, Vertical Static Load and Axle Load |
|
BSI BS ISO 1919 |
Corr.1 Road Vehicles - M14 X 1,25 Spark Plugs with Flat Seating and Their Cylinder Head Housings-CORR 10530; July 1999; |
|
BSI BS ISO 21750 |
Road vehicles Safety enhancement in conjunction with tyre inflation pressure monitoring |
|
BSI BS ISO 21950 |
Coated abrasives Plain discs |
|
BSI BS ISO 22168 |
Road vehicles Holding test of coatings influencing the colour of light emitted by light source(s) Test methods |
|
BSI BS ISO 22896 |
Road vehicles Deployment and sensor bus for occupant safety systems |
|
BSI BS ISO 22902-2 |
Road vehicles Automotive multimedia interface Part 2: Use cases |
|
BSI BS ISO 22902-5 |
Road vehicles Automotive multimedia interface Part 5: Common message set |
|
BSI BS ISO 22977 |
Road vehicles M12 × 1,25 spark-plugs with flat seating and 14 mm bi-hexagon and their cylinder head housing |
|
BSI BS ISO 2705 |
Road Vehicles - M12 X 1,25 Spark Plugs with Flat Seating and Their Cylinder Head Housings |
|
BSI BS ISO 2982-1 |
Roller Bearings - Accessories Part 1: Tapered Sleeves - Dimensions (E) |
|
BSI BS ISO 3096 |
Rolling Bearings - Needle Rollers - Dimensions and Tolerances-Supersedes BS 5773: Part 5: 1979 and BS 5773: Part 6: 1980; |
|
BSI BS ISO 3842 |
Road Vehicles - Fifth Wheels - Interchangeability |
|
BSI BS ISO 4010 |
Diesel Engines - Calibrating Nozzle, Delay Pintle Type |
|
BSI BS ISO 4927 |
Road vehicles Elastomeric boots for cylinders for drum type hydraulic brake wheel cylinders using a non-petroleum base hydraulic brake fluid (Service temperature 120 degrees C max.) |
|
BSI BS ISO 4930 |
Road vehicles Elastomeric seals for hydraulic disc brake cylinders using a non-petroleum base hydraulic brake fluid (Service temperature 150 °C max.) |
|
BSI BS ISO 500-3 |
Agricultural tractors Rear-mounted power take-off types 1, 2 and 3 Part 3: Main PTO dimensions and spline dimensions, location of PTO-Together with BS ISO 500-1:2006 and BS ISO 500-2:2006 supersedes BS 5861:1992 |
|
BSI BS ISO 6020-3 |
Hydraulic Fluid Power - Mounting Dimensions for Single Rod Cylinders, 16 MPa (160 Bar) Series Part 3: Compact Series with Bores from 250 mm to 500 mm (E) |
|
BSI BS ISO 6621-4 |
Internal combustion engines Piston rings Part 4: General specifications-Supersedes BS 5341-6.4:1992; |
|
BSI BS ISO 6622-1 |
Internal combustion engines Piston rings Part 1: Rectangular rings made of cast iron-Supersedes BS 5341-7.1.1: 1992; |
|
BSI BS ISO 6686 |
Equipment for Crop Protection - Anti-Drip Devices - Determination of Performance (E) |
|
BSI BS ISO 6813 |
Road Vehicles - Collision Classification - Terminology-Supersedes BS AU 191:1983; |
|
BSI BS ISO 7063 |
Rolling bearings Needle roller bearing track rollers Boundary dimensions and tolerances |
|
BSI BS ISO 7112 |
Machinery for Forestry - Portable Hand-Held Brush-Cutters and Grass-Trimmers - Vocabulary |
|
BSI BS ISO 7299 |
Diesel Engines - End-Mounting Flanges for Fuel Injection Pumps |
|
BSI BS ISO 7588-3 |
Road Vehicles - Electrical/Electronic Switching Devices - Part 3: Microrelays |
|
BSI BS ISO 7612 |
Diesel engines Base-mounted in-line fuel injection pumps and high-pressure supply pumps for common rail fuel injection systems Mounting dimensions |
|
BSI BS ISO 8443 |
Rolling Bearings - Radial Ball Bearings with Flanged Outer Ring - Flange Dimensions-Supersedes BS 5646-7: 1986; |
|
BSI BS ISO 8820-2 |
Road vehicles Fuse-links Part 2: User’s guide |
|
BSI BS ISO 8893 |
Forestry Machinery - Portable Brush Cutters and Grass Trimmers - Engine Performance and Fuel Consumption |
|
BSI BS ISO 9085 |
Calculation of Load Capacity of Spur and Helical Gears - Application for Industrial Gears |
|
BSI BS ISO/TR 14179-2 |
Gears - Thermal Capacity - Part 2: Thermal Load Carrying Capacity |
|
BSI DD CEN/TS 12201-7 |
Plastics piping systems for water supply Polyethylene (PE) Part 7: Guidance for the assessment of conformity |
|
BSI DD ENV 12314-1 |
Road Transport and Traffic Telematics - Automatic Vehicle and Equipment Identification Part 1: Reference Architectures and Terminology |
|
BSI DD ISO/PAS 11154 |
Road vehicles  Roof load carriers-CORR 16996: March 30, 2007 |
|
BSI DD ISO/TS 17104 |
Rotary tool for threaded fasteners Hydraulic impulse tools Performance test method |
|
BSI PAS 27 |
Corr.1 Unplasticized Poly(Vinyl Chloride) Alloy (PVC-A) Pipes and Bends for Water under Pressure-CORR 10516; May 1999; |
|
BSI PD IEC/TR 62331 |
Pulsed field magnetometry |
|
BSI BS 1468 |
Tin Anodes and Tin Salts for Electroplating-Amd 1; |
|
BSI BS 2857 |
Nickel-Iron Transformer and Choke Laminations |
|
BSI BS 3226 |
Thimbles for Natural Fibre Ropes-Amd 1; |
|
BSI BS 3457 |
Materials for Water Tap and Stopvalve Seat Washers |
|
BSI BS 3944 PART 1 |
Colour and Diffusion Filter Material for Theatre, Television and Similar Entertainment Purposes Part 1: Specification for Flammability and Dimensional Stability |
|
BSI BS 4653 PART 2 |
(OBSOLESCENT)1970 Paper Covered Copper Conductors Part 2: Rectangular Conductors |
|
BSI BS 4742 PART 4 |
Hydraulic Equipment for Agricultural Machinery Part 4: Hydraulic Couplings on Braking Systems for Trailers and Trailed Equipment |
|
BSI BS 4742 PART 6 |
Hydraulic Equipment for Agricultural Machinery Part 6: Dimensions and Location of Agricultural Tractor Hydraulic Return to Sump Porting |
|
BSI BS 4857 PART 1 |
Methods for Testing and Rating Terminal Reheat Units for Air Distribution Systems Part 1: Thermal and Aerodynamic Performance |
|
BSI BS 5173 SEC 102.4 |
Rubber and Plastics Hoses and Hose Assemblies Part 102: Hydraulic Pressure Tests Section 102.4: Determination of Volumetric Expansion of Hydraulic Hoses |
|
BSI BS 5626 SEC 3.3 |
Cellulosic Papers for Electrical Purposes Part 3: Specifications for Individual Materials Section 3.3: Crepe Paper |
|
BSI BS 5626 SEC 3.4 |
Cellulosic Papers for Electrical Purposes Part 3: Specifications for Individual Materials Section 3.4: Electrolytic Capacitor Papers |
|
BSI BS 5676 ADD 1 |
Reciprocating Internal Combustion Engines Addendum 1: Symbols-Covered by ISO 2710-1:2000 and ISO 2710-2:1999 |
|
BSI BS 6156 |
Low-Frequency Miniature Equipment Wires with Solid or Stranded Conductor, Fluorinated Polyhydrocarbon Type Insulation, Single-Amd 1; |
|
BSI BS 6168 |
Specification for Non-metallic spur gears-AMD 6364: May 1991 |
|
BSI BS 6483 PART 1 |
Fertilizer Distributors Part 1: Methods of Evaluating Performance Under Laboratory and Field Conditions |
|
BSI BS 6764 |
Habitation and Stability Requirements for Leisure Accommodation Vehicles: Leisure Homes-ISO 8817: 1990; Replaces BS 4989: 1984 |
|
BSI BS 6818 PART 1 |
Front-Mounted Linkage and Power Take-off for Agricultural Wheeled Tractors Part 1: Power Take-off |
|
BSI BS 6873 |
Filament Lamps for Cycles-AMD 10461; August 1999; Supersedes BS 941: 1970; |
|
BSI BS 7436 |
Data Transfer Between Agricultural Tractors and Attached Machinery (Data Bus Protocol) (E) |
|
BSI BS 7496 PART 2 |
Cross-Recessed Tapping Screws Part 2: Specification for Countersunk Flat Head Screws (AMD 8502) March 15, 1995 (E)-Amd 1; |
|
BSI BS 7647 |
Radio Teleswitches for Tariff and Load Control |
|
BSI BS 7679 |
Plain Bearings - Quality Control Techniques and Inspection of Geometrical and Material Quality Characteristics (ISO 12301: 1992) (E) |
|
BSI BS 7772 |
Plain Bearings - Measurement of Wall Thickness of Thin-Walled Half-Bearings and Thin-Walled Bushes (ISO 12306: 1994) (E) |
|
BSI BS 7961 |
Specification for a device for measuring the static vertical mass (noseweight) at the coupling point of a towed vehicle |
|
BSI BS 949 PART 5 |
Screwing Taps Part 5: Nomenclature and Terminology |
|
BSI BS AU 177A |
Electrical Connections Between Towing Vehicles and Trailers with 6V or 12V Electrical Equipment: Type 12S (Supplementary) (Formerly BS AU 177: 1980)-Amd 1 |
|
BSI BS AU 241 |
Mechanical Coupling Between Tractors and Semi-Trailers: Interchangeability-ISO 1726: 1989; Covered by ISO 1726 |
|
BSI BS EN 116503 |
Harmonized system of quality assessment for electronic components Blank detail specification Electromechanical all-or-nothing TELECOM relays of assessed quality, dual-in-line, with 14 mm× 9 mm base |
|
BSI BS EN 12761-1 |
Agricultural and Forestry Machinery - Sprayers and Liquid Fertilizer Distributors - Environmental Protection - Part 1: General |
|
BSI BS EN 13021 |
Winter service machines Safety requirements |
|
BSI BS EN 13878 |
Leisure accommodation vehicles - Terms and definitions-Supersedes BS EN 27418:1994; |
|
BSI BS EN 14218 |
Hexagon nuts with flange Fine pitch thread |
|
BSI BS EN 15416-5 |
Adhesives for load bearing timber structures other than phenolic and aminoplastic Test methods Part 5: Determination of conventional pressing time |
|
BSI BS EN 19812 |
Road vehicles  M10 × 1 compact spark-plugs with flat seating and 16 mm hexagon and their cylinder head housings |
|
BSI BS EN 28029 |
Plastics Hose - General Purpose Collapsible Water Hose, Textile Reinforced - Specification (ISO 8029: 1985) (AMD 7525) April 15, 1993 (Formerly BS 6848: 1987)-Amd 1; |
|
BSI BS EN 28970 |
Timber Structures - Testing of Joints Made with Mechanical Fasteners - Requirements for Wood Density (ISO 8970: 1989) |
|
BSI BS EN 50050 |
Electrical Apparatus for Potentially Explosive Atmospheres - Electrostatic Hand-Held Spraying Equipment-Supersedes BS 6742-1:1987; |
|
BSI BS EN 50089 |
Cast Resin Partitions for Metal-Enclosed Gas-Filled High-Voltage Switchgear and Controlgear (AMD 8239) July 15, 1994 (E)-Amd 1; |
|
BSI BS EN 50225 |
Code of Practice for the Safe Use of Fully Enclosed Oil-Filled Electrical Equipment Which May be Contaminated with PCBs |
|
BSI BS EN 50375 |
Testing methodology for wipers used in electrical insulating oil |
|
BSI BS EN 60455-3-3 |
Resin based reactive compounds used for electrical insulation Part 3: Specifications for individual materials - Sheet 3: Unfilled polyurethane compounds-Supersedes BS 5664-3.3: 1995; |
|
BSI BS EN 60512-11-11 |
Connectors for Electronic Equipment - Tests and Measurements - Part 11-11: Climatic Tests - Test 11k: Low Air Pressure |
|
BSI BS EN 60512-11-4 |
Connectors for Electronic Equipment - Tests and Measurements - Part 11-4: Climatic Tests - Test 11d: Rapid Change of Temperature |
|
BSI BS EN 60512-12-6 |
Electromechanical Components for Electronic Equipment - Basic Testing Procedures and Measuring Methods Part 12: Soldering Tests Section 6: Test 12f. Sealing Against Flux and Cleaning Solvents in Machine Soldering-IEC 512-12-6: 1996; |
|
BSI BS EN 60512-25-4 |
Connectors for Electronic Equipment - Tests and Measurements - Part 25-4: Test 25d - Propagation Delay-IEC 60512-25-4:2001; |
|
BSI BS EN 60512-5-1 |
Connectors for Electronic Equipment - Tests and Measurements - Part 5-1: Current-Carrying Capacity Tests - Tests 5a: Temperature Rise |
|
BSI BS EN 60512-6-5 |
Electromechanical Components for Electronic Equipment - Basic Testing Procedures and Measuring Methods Part 6-5: Dynamic Stress Tests Test 6e: Random Vibration |
|
BSI BS EN 60544-4 |
Electrical insulating materials Determination of the effects of ionizing radiation Part 4: Classification system for service in radiation environments-Supersedes BS 7811-4:1995; |
|
BSI BS EN 60556 |
Gyromagnetic materials intended for application at microwave frequencies - measuring methods for properties |
|
BSI BS EN 609-2 |
Agricultural and Forestry Machinery - Saftey of Log Splitters - Part 2: Screw Splitters |
|
BSI BS EN 61033 |
Test methods for the determination of bond strength of impregnating agents to an enamelled wire substrate |
|
BSI BS EN 61240 |
Piezoelectric Devices - Preparation of Outline Drawings of Surface-Mounted Devices (SMD) for Frequency Control and Selection - General Rules-IEC 1240: 1994; |
|
BSI BS EN 61788-7 |
Superconductivity Part 7: Electronic characteristic measurements Surface resistance of superconductors at microwave frequencies |
|
BSI BS EN 61969-2-1 |
Mechanical Structures for Electronic Equipment - Outdoor Enclosures - Part 2-1: Detail Specification - Dimensions for Cabinets-IEC 61969-2-1: 2000; |
|
BSI BS EN 62005-1 |
Reliability of Fibre Optic Interconnecting Devices and Passive Components - Part 1: Introductory Guide and Definitions-IEC 62005-1:2001; |
|
BSI BS EN 62044-2 |
Cores made of soft magnetic materials - Measuring methods - Part 2: Magnetic properties at low excitation level |
|
BSI BS EN 62193 |
Live working Telescopic sticks and telescopic measuring sticks |
|
BSI BS EN 62317-7 |
Ferrite cores Dimensions Part 7: EER-cores |
|
BSI BS EN 62317-9 |
Ferrite cores  Dimensions  Part 9: Planar cores-AMD 17096: May 31, 2007 |
|
BSI BS EN 62358 |
Ferrite cores  Standard inductance factor (AL) and its tolerance-CORR 16881: January 31, 2007 |
|
BSI BS EN 705 |
Plastics Piping Systems - Glass-Reinforced Thermosetting Plastics (GRP) Pipes and Fittings - Methods for Regression Analyses and Their Use (E) |
|
BSI BS EN 707 |
Agricultural Machinery - Slurry Tankers - Safety |
|
BSI BS EN ISO 10807 |
Pipework - Corrugated Flexible Metallic Hose Assemblies for the Protection of Electrical Cables in Explosive Atmosphere |
|
BSI BS EN ISO 15005 |
Road vehicles Ergonomic aspects of transport information and control systems Dialogue management principles and compliance procedures |
|
BSI BS EN ISO 15007-1 |
Road Vehicles - Measurement of Driver Visual Behaviour with Respect to Transport Information and Control Systems - Part 1: Definitions and Parameters-CORR 14578: July 11, 2003; |
|
BSI BS EN ISO 15106-3 |
Plastics Film and sheeting Determination of water vapour transmission rate Part 3: Electrolytic detection sensor method |
|
BSI BS EN ISO 15984 |
Open end blind rivets with break pull mandrel and countersunk head A2/A2-CORR 14329: February 5, 2003; CORR 15324: November 23, 2004; Together with BS EN ISO 15980:2002, BS EN ISO 15981:2002, BS EN ISO 15982:2002, BS EN ISO 15983:2002, BS EN ISO 16582:2002, BS EN ISO 16583:2002, BS EN ISO 16584:2002 and BS EN ISO 16585:2002, supersedes BS 7349-2:1993 |
|
BSI BS EN ISO 16585 |
Closed end blind rivets with pull mandrel and protruding head A2/SSt-CORR 14314: January 24, 2003; CORR 15328: November 23, 2004; Together with BS EN ISO 15980:2002, BS EN ISO 15981:2002, BS EN ISO 15982:2002, BS EN ISO 15983:2002, BS EN ISO 15984:2002, BS EN ISO 16582:2002, BS EN ISO 16583:2002 and BS EN ISO 16584:2002 supersedes BS 7349-2:1993 |
|
BSI BS EN ISO 5771 |
Rubber Hose and Hose Assemblies for Transferring Anhydrous Ammonia - Specification (E) |
|
BSI BS EN ISO 6945 |
Rubber Hoses - Determination of Abrasion Resistance of the Outer Cover-AMD 10939:April 2001; Supersedes BS 5173-103.9:1986; |
|
BSI BS EN ISO 7369 |
Pipework Metal hoses and hose assemblies Vocabulary |
|
BSI BS EN ISO 7662 |
Rubber and Plastics Hoses - Determination of Abrasion of Lining |
|
BSI BS EN ISO 8092-1 |
Road Vehicles - Connections for On-Board Electrical Wiring Harnesses - Part 1: Tabs for Single-Pole Connections - Dimensions and Specific Requirements-Supersedes BS EN 28092-1: 1992; |
|
BSI BS EN ISO 8092-3 |
Road Vehicles - Connections for On-Board Electrical Wiring Harnesses - Part 3: Tabs for Multi-Pole Connections - Dimensions and Specific Requirements (ISO 8092-3: 1996) |
|
BSI BS ISO 10300-2 |
Calculation of Load Capacity of Bevel Gears - Part 2: Calculation of Surface Durability (Pitting) |
|
BSI BS ISO 10521-1 |
Road vehicles Road load Part 1: Determination under reference atmospheric conditions |
|
BSI BS ISO 10627-2 |
Hydraulic Agricultural Sprayers - Data Sheets Part 2: Technical Specifications Related to Components (E) |
|
BSI BS ISO 11096 |
Road Vehicles Pedestrian Protection Impact Test Method for Pedestrian Thigh, Leg and Knee |
|
BSI BS ISO 113 |
Rolling Bearings - Plummer Block Housings - Boundary Dimensions-Supersedes BS 5646-4: 1995; |
|
BSI BS ISO 11512 |
Machinery for Forestry - Tracked Special Machines - Performance Criteria for Brake Systems (E) |
|
BSI BS ISO 11783-6 |
Tractors and machinery for agriculture and forestry Serial control and communications data network Part 6: Virtual terminal-CORR 16036: March 2006 |
|
BSI BS ISO 12003-1 |
Agricultural and forestry tractors Narrow-track wheeled tractors Part 1: Front-mounted roll-over protective structures |
|
BSI BS ISO 12240-2 |
Spherical Plain Bearings - Part 2: Angular Contact Radial Spherical Plain Bearings |
|
BSI BS ISO 12368 |
Agricultural Vehicles - Mechanical Hook-Type Connections on Towing Vehicles - Test Methods and Requirements |
|
BSI BS ISO 13555-1 |
Diesel engines Procedure for checking the dynamic timing of diesel fuel injection equipment Part 1: Preconditioning |
|
BSI BS ISO 13562-2 |
Industrial Variable-Reach Trucks - Part 2: Additional Stability Tests for Trucks Handling Freight Containers of Length 6 m amd Above |
|
BSI BS ISO 13674-1 |
Road vehicles - Test method for the quantification of on-centre handling - Part 1: Weave test |
|
BSI BS ISO 14512 |
Passenger Cars - Straight-Ahead Braking on Surfaces with Split Coefficient of Friction - Open-Loop Test Method |
|
BSI BS ISO 14513 |
Road vehicles Pedestrian protection Head impact test method |
|
BSI BS ISO 14728-1 |
Rolling bearings Linear motion rolling bearings Part 1: Dynamic load ratings and rating life |
|
BSI BS ISO 14792 |
Road vehicles Heavy commercial vehicles and buses Steady-state circular tests |
|
BSI BS ISO 15028 |
Plastics Aromatic isocyanates for use in the production of polyurethanes Determination of hydrolysable chlorine |
|
BSI BS ISO 16121-1 |
Road vehicles Ergonomic requirements for the driver’s workplace in line-service buses Part 1: General description, basic requirements |
|
BSI BS ISO 16121-4 |
Road vehicles - Ergonomic requirements for the driver's workplace in line-service buses - Part 4: Cabin environment |
|
BSI BS ISO 16232-1 |
Road vehicles  Cleanliness of components of fluid circuits  Part 1: Vocabulary |
|
BSI BS ISO 16232-2 |
Road vehicles  Cleanliness of components of fluid circuits  Part 2: Method of extraction of contaminants by agitation |
|
BSI BS ISO 16232-6 |
Road vehicles  Cleanliness of components of fluid circuits  Part 6: Particle mass determination by gravimetric analysis |
|
BSI BS ISO 16232-8 |
Road vehicles  Cleanliness of components of fluid circuits  Part 8: Particle nature determination by microscopic analysis |
|
BSI BS ISO 16232-9 |
Road vehicles  Cleanliness of components of fluid circuits  Part 9: Particle sizing and counting by automatic light extinction particle counter |
|
BSI BS ISO 16234 |
Heavy commercial vehicles and buses  Straight-ahead braking on surfaces with split coefficient of friction  Open-loop test method |
|
BSI BS ISO 16287 |
Plain bearings Thermoplastic bushes Dimensions and tolerances |
|
BSI BS ISO 17356-5 |
Road vehicles Open interface for embedded automotive applications Part 5: OSEK/VDX Network Management (NM) |
|
BSI BS ISO 17455 |
Plastics piping systems  Multilayer pipes  Determination of the oxygen permeability of the barrier pipe |
|
BSI BS ISO 18164 |
Passenger car, truck, bus and motorcycle tyres Methods of measuring rolling resistance |
|
BSI BS ISO 18653 |
Gears Evaluation of instruments for the measurement of individual gears |
|
BSI BS ISO 22368-1 |
Crop protection equipment Test methods for the evaluation of cleaning systems Part 1: Internal cleaning of complete sprayers |
|
BSI BS ISO 22866 |
Equipment for crop protection Methods for field measurement of spray drift-Supersedes BS 6916-8:1988 |
|
BSI BS ISO 3894 |
Road vehicles Wheels/rims for commercial vehicles Test methods |
|
BSI BS ISO 4008-3 |
Road vehicles Fuel injection pump testing Part 3: Application and test procedures |
|
BSI BS ISO 4081 |
Rubber hoses and tubing for cooling systems for .. internal-combustion engines .. Specification-Supersedes BS 7038: 1998 |
|
BSI BS ISO 4093 |
Diesel Engines - Fuel Injection Pumps - High-Pressure Pipes for Testing |
|
BSI BS ISO 4383 |
Plain Bearings - Multilayer Materials for Thin-Walled Plain Bearings |
|
BSI BS ISO 500-2 |
Agricultural tractors Rear-mounted power take-off types 1, 2 and 3 Part 2: Narrow-track tractors, dimensions for master shield and clearance zone-Together with BS ISO 500-1:2006 and BS ISO 500-3:2006 supersedes BS 5861:1992 |
|
BSI BS ISO 6118 |
Road vehicles Elastomeric cups and seals for cylinders for hydraulic braking systems using a non-petroleum base hydraulic brake fluid (service temperature 70 °C max.) |
|
BSI BS ISO 6489-2 |
Agricultural vehicles Mechanical connections between towed and towing vehicles Part 2: Specifications for clevis coupling 40 |
|
BSI BS ISO 6533 |
Forestry Machinery - Portable Chain-Saw Front Hand-Guard - Dimensions and Clearances-Supersedes BS 6916 Part 3 |
|
BSI BS ISO 6622-2 |
Internal combustion engines Piston rings Part 2: Rectangular rings made of steel |
|
BSI BS ISO 6624-4 |
Internal combustion engines Piston rings Part 4: Half keystone rings made of steel |
|
BSI BS ISO 6650-4 |
Road vehicles Sheath-type glow-plugs with conical seating and their cylinder head housing Part 4: M8 .. 1 glow-plugs |
|
BSI BS ISO 7113 |
Portable Hand-Held Forestry Machines - Cutting Attachments for Brush Cutters - Single Piece Metal Blades |
|
BSI BS ISO 7148-2 |
Plain Bearings - Testing of the Tribological Behavior of Bearing Materials - Part 2: Testing of Polymer-Based Bearing Materials |
|
BSI BS ISO 7918 |
Forestry Machinery - Portable Brush Cutters and Grass Trimmers - Cutting Attachment Guard Dimensions (E) |
|
BSI BS ISO 8082 |
Self-Propelled Machinery for Forestry - Roll-Over Protective Structures - Laboratory Tests and Performance Requirements (E) |
|
BSI BS ISO 8820-6 |
Road vehicles  Fuse-links  Part 6: Single-bolt fuse-links |
|
BSI BS ISO 9628 |
Rolling bearings  Insert bearings and eccentric locking collars  Boundary dimensions and tolerances-CORR 17125: May 31 2007 |
|
BSI DD CEN/TS 1555-7 |
Plastics piping systems for the supply of gaseous fuels Polyethylene (PE) Part 7: Guidance for the assessment of conformity |
|
BSI DD CLC TS 50349 |
Qualification of electrical installation contractors |
|
BSI DD CLC/TS 50217 |
Guide for in situ measurements In situ measurement of disturbance emission |
|
BSI DD ENV 13093 |
Public Transport - Road Vehicles - Driver's Console Mechanical Interface Requirements - Minimum Display and Keypad Parameters |
|
BSI DD ENV 13149-2 |
Public Transport - Road Vehicle Scheduling and Control Systems - Part 2: WORLDFIP Cabling Specifications |
|
BSI DD IEC TS 62143 |
Electrical installations for lighting and beaconing of aerodromes Aeronautical ground lighting systems Guidelines for the development of a safety lifecycle methodology |
|
BSI DD ISO/TS 15827 |
Road vehicles  Test procedures  Evaluating small female dummy arm and forearm interactions with driver frontal airbags and side airbags |
|
BSI PAS 43 |
Safe working of vehicle breakdown, recovery and removal operations – Management system specification-Second Edition |
|
BSI PD CLC/TR 50473 |
Recommendations for dimensional co-ordination between enclosures and built-in devices for rail fixing for household and similar installations |
|
BSI BS 2945 |
Axes and Hatchets-AMD 892: December 15, 1995 |
|
BSI BS 3529 |
Dimensions of Flywheel Housing Mounting Pads and Brackets for I.C. Engines |
|
BSI BS 3575 |
Rivets for the Attachment of Friction Linings |
|
BSI BS 4161 PART 4 |
Gas Meters Part 4: Plate Constructed Positive Displacement Diaphragm Meters for a Pressure of 350 mbar (5lbf/in2) and up to 170 Cubic Meters (6000 Cubic Feet) per Hour Rating |
|
BSI BS 4480 PART 4 |
Plain Bearings. Metric Series Part 4: Dimensions, Tolerances and Methods of Checking Wrapped Bushes |
|
BSI BS 4742 PART 3 |
Hydraulic Equipment for Agricultural Machinery Part 3: Dimensions and Pressure Rating of Single-Acting Telescopic Tipping Cylinders for Trailers |
|
BSI BS 5173 SEC 102.3 |
Rubber and Plastics Hoses and Hose Assemblies Part 102: Hydraulic Pressure Tests Section 102.3: Determination of Volumetric Expansion of Fuel- Dispensing Pump Hoses |
|
BSI BS 5279 |
Dimensions of Fuel Filler Openings of Earth-Moving Machinery |
|
BSI BS 5689 SEC 3.1 |
Varnished Fabrics for Electrical Purposes Part 3: Specifications for Individual Materials Section 3.1: Oleoresinous Varnish - Cotton Base, OR/C (IEC 394-3-1: 1976) (E) |
|
BSI BS 5689 SEC 3.2 |
Varnished Fabrics for Electrical Purposes Part 3: Specifications for Individual Materials Section 3.2: Glass- Fabric Based Varnished Fabrics with Epoxy, Polyurethane, Silicone, Polyester, Bituminous or Oleoresinous Varnish (IEC 394-3-2: 1988) (E) |
|
BSI BS 5832 |
Compacted Waste Cylinders for Lift-Off Vehicles |
|
BSI BS 5944 PART 6 |
Measurement of Airborne Noise from Hydraulic Fluid Power Systems and Components Part 6: Method of Test for Pumps Using a Parallelepiped Microphone Array (ISO 4412-3: 1991) (E) |
|
BSI BS 5944-5 |
Measurement of airborne noise from hydraulic fluid power systems and components Part 5: Simplified method of determining sound power levels from pumps using an anechoic chamber |
|
BSI BS 6091 PART 2 |
Vulcanized Fibre for Electrical Purposes Part 2: Methods of Test-Supersedes BS 216:1961 |
|
BSI BS 7403 PART 4 |
Full-Flow Lubricating Oil Filters for Internal Combustion Engines Part 4: Methods of Test for Initial Particle Retention Efficiency, Life and Cumulative Efficiency (Gravimetric Method)-BS 7403: Part 4, Together with BS 7403: Parts 1,2 and 3 Supersedes BS 4836: 1972; ISO 4548-4: 1997; |
|
BSI BS 7403 PART 9 |
Full-Flow Lubricating Oil Filters for Internal Combustion Engines Part 9: Method of Test for Inlet and Outlet Anti-Drain Valves (ISO 4548-9: 1995) (E) |
|
BSI BS 7496 PART 3 |
Cross-Recessed Tapping Screws Part 3: Specification for Raised Countersunk Head Screws-AMD 8501; April 15, 1995; |
|
BSI BS 7705 |
Brake Systems for Special Wheeled Forestry Machines (ISO 11169: 1993) (E) |
|
BSI BS 7762 |
Plain Bearings - Quality Characteristics - Statistical Process Control (SPC) (ISO 12302: 1993) (E) |
|
BSI BS AU 166 |
Mounting of Mechanical Coupling Devices on Rear Cross Members of Trucks-Subject Covered by ISO 3584 |
|
BSI BS AU 235 PART 2 |
Fifth Wheel Couplings for Commercial Vehicles Part 2: Method of Testing Strength of Coupling Pins (ISO 8716: 1988) |
|
BSI BS EN 116501 |
Harmonized system of quality assessment for electronic components Blank detail specification Electromechanical all-or-nothing TELECOM relays of assessed quality |
|
BSI BS EN 12525 |
Agricultural Machinery - Front Loaders - Safety-AMD 16770: December 29, 2006 |
|
BSI BS EN 12645 |
Pressure Gauges - Apparatus for Inspection of Pressure and/or Inflation of Tyres for Motor Vehicles - Metrology, Requirements and Testing-Supersedes BS 4613-1: 1970, BS 4613-2: 1970 and BS 4613-3: 1972; |
|
BSI BS EN 12806 |
Automotive liquefied petroleum gas components Other than containers |
|
BSI BS EN 13406 |
Agricultural machinery Slurry tankers and spreading devices Environmental protection Requirements and test methods for the spreading precision |
|
BSI BS EN 13448 |
Aricultural and Forestry Machinery - Inter-Row Mowing Units - Safety |
|
BSI BS EN 1374 |
Agricultural machinery Silos stationary unloaders for round silos Safety-CORR 15331:August 16, 2004 |
|
BSI BS EN 13740-2 |
Agricultural machinery Solid fertilizer line-distributors Environmental protection Part 2: Test methods |
|
BSI BS EN 13760 |
Automotive LPG filling system for light and heavy duty vehicles Nozzle, test requirements and dimensions |
|
BSI BS EN 13790-2 |
Agricultural machinery Sprayers Inspection of sprayers in use Part 2: Air-assisted sprayers for bush and tree crops |
|
BSI BS EN 13856 |
Minimum requirements for the content of the user manual for automotive LPG systems |
|
BSI BS EN 14453 |
Devices to prevent pollution by backflow of potable water Pipe interrupter with permanent atmospheric vent DN 10 to DN 20 Family D, type C-Supersedes BS 6281-3: 1982 |
|
BSI BS EN 14483-4 |
Vitreous and porcelain enamels Determination of resistance to chemical corrosion Part 4: Determination of resistance to chemical corrosion by alkaline liquids using a cylindrical vessel-CORR 15504:December 10, 2004; Supersedes BS 1344-6:1971, BS 1344-15:1997 and BS 1344-17:1998 |
|
BSI BS EN 22339 |
Taper Pins, Unhardened (ISO 2339: 1986) (E) |
|
BSI BS EN 27435 |
Slotted Set Screws with Long Dog Point (ISO 7435: 1983) (E) |
|
BSI BS EN 30326-1 |
Mechanical Vibration - Laboratory Method for Evaluating Vehicle Seat Vibration Part 1: Basic Requirements (ISO 10326-1 : 1992) (E) |
|
BSI BS EN 3202 |
Holes and Traps for T-Head Bolts Design Standards (E) |
|
BSI BS EN 3682-005 |
Aerospace series  Connectors, plug and receptacle, electrical, rectangular, interchangeable insert type, rack to panel, operating temperature 150 °C continuous  Part 005: Size 2 plug  Product standard |
|
BSI BS EN 50223 |
Automatic Electrostatic Application Equipment for Flammable Flock Material |
|
BSI BS EN 50374 |
Conductor cars |
|
BSI BS EN 60512-11-2 |
Connectors for Electronic Equipment - Tests and Measurements - Part 11-2: Climatic Tests - Test 11b: Combined/Sequential Cold, Low Air Pressure and Damp Heat-IEC 60512-11-2: 2002; |
|
BSI BS EN 60512-11-5 |
Connectors for Electronic Equipment - Tests and Measurements - Part 11-5: Climatic Tests - Test 11e: Mould Growth |
|
BSI BS EN 60512-12-7 |
Connectors for Electronic Equipment - Tests and Measurements - Part 12-7: Soldering Tests - Test 12g: Solderability, Wetting Balance Method-IEC 60512-12-7: 2001; |
|
BSI BS EN 60512-16-20 |
Electromechanical Components for Electronic Equipment - Basic Testing Procedures and Measuring Methods Part 16: Mechanical Tests on Contacts and Terminations Section 20: Test 16t. Mechanical Strength (Wired Termination of Solderless Connections)-IEC 512-16-20: 1996; |
|
BSI BS EN 60512-4-2 |
Connectors for Electronic Equipment - Tests and Measurements - Part 4-2: Voltage Stress Tests - Test 4b: Partial Discharge |
|
BSI BS EN 60512-6-2 |
Connectors for Electronic Equipment - Tests and Measurements - Part 6-2: Dynamic Stress Tests - Test 6b: Bump-IEC 60512-6-1: 2002; |
|
BSI BS EN 60564 |
D.C. Bridges for Measuring Resistance-AMD 7912: October 1993; Renumbers BS 5764: 1979 |
|
BSI BS EN 60634 |
Heat Test Source (H.T.S.) Lamps for Carrying Out Heating Tests on Luminaires (E) |
|
BSI BS EN 60684-3-248 |
Flexible insulating sleeving  Part 3: Specifications for individual types of sleeving  Sheet 248: General purpose, heat-shrinkable, dual wall polyolefin sleeving, flame retarded, shrink ratios 2:1, 3:1, 4:1 |
|
BSI BS EN 60806 |
Determination of the maximum symmetrical radiation field from a rotating anode X-ray tube for medical diagnosis-: 1985 |
|
BSI BS EN 609-1 |
Agricultural and forestry machinery Safety of log splitters Part 1: Wedge splitters-AMD 14948:April 7, 2004 |
|
BSI BS EN 61143-1 |
Electrical Measuring Instruments - X-t Recorders Part 1: Definitions and Requirements-AMD 8388: January 1995; AMD 10283: February 1999; Renumbers BS 7610-1: 1992 |
|
BSI BS EN 61185 |
Ferrite cores (ETD-cores) intended for use in power supply applications - Dimensions |
|
BSI BS EN 61358 |
Acceptance Inspection for Direct Connected Alternating Current Static Watt-Hour Meters for Active Energy (Classes 1 and 2)-IEC 1358: 1996; |
|
BSI BS EN 61969-2-2 |
Mechanical Structures for Electronic Equipment - Outdoor Enclosures - Part 2-2: Detail Specification - Dimensions for Cases-IEC 61969-2-2:2000; |
|
BSI BS EN 61982-1 |
Secondary batteries for the propulsion of electric road vehicles  Part 1: Test parameters |
|
BSI BS EN 62024-1 |
High frequency inductive components Electrical characteristics and measuring methods Part 1: Nanohenry range chip inductor |
|
BSI BS EN 62211 |
Inductive components Reliability management |
|
BSI BS EN 62231 |
Composite station post insulators for substations with a.c. voltages greater than 1 000 V up to 245 kV  Definitions, test methods and acceptance criteria |
|
BSI BS EN 62317-4 |
Ferrite cores Dimensions Part 4: RM-cores and associated parts |
|
BSI BS EN 62317-8 |
Ferrite cores  Dimensions  Part 8: E-cores |
|
BSI BS EN 629-2 |
Transportable Gas Cylinders - 25E Taper Thread for Connection of Valves to Gas Cylinders Part 2: Gauge Inspection |
|
BSI BS EN 632 |
Agricultural Machinery - Combine Harvesters and Forage Harvesters - Safety (E) |
|
BSI BS EN ISO 10510 |
Tapping Screw and Washer Assemblies with Plain Washers |
|
BSI BS EN ISO 11116-2 |
Gas Cylinders - 17E Taper Thread for Connection of Valves to Gas Cylinders - Part 2: Inspection Guages |
|
BSI BS EN ISO 11680-2 |
Machinery for Forestry - Safety Requirements and Testing for Pole-Mounted Powered Pruners - Part 2: Units for Use with a Back-Pack Power Source-AMD 14046: February 13, 2003; |
|
BSI BS EN ISO 13929 |
Small Craft - Steering Gear - Geared Link Systems |
|
BSI BS EN ISO 14915-1 |
Software ergonomics for multimedia user interfaces Part 1: Design principles and framework-CORR 14317: January 31, 2003; |
|
BSI BS EN ISO 17287 |
Road vehicles Ergonomic aspects of transport information and control systems Procedure for assessing suitability for use while driving-CORR 14614: August 1, 2003; |
|
BSI BS EN ISO 8733 |
Parrallel Pins with Internal Thread, of Unhardened Steel or Austenitic Stainless Steel-Supersedes BS EN 28733: 1992 Which is Withdrawn; |
|
BSI BS EN ISO 9455-6 |
Soft Soldering Fluxes - Test Methods Part 6: Determination and Detection of Halide (Excluding Fluoride) Content-Partially Supersedes BS 5625: 1985; |
|
BSI BS ISO 10521-2 |
Road vehicles Road load Part 2: Reproduction on chassis dynamometer |
|
BSI BS ISO 10838-3 |
Mechanical Fittings for Polyethylene Piping Systems for the Supply of Gaseous Fuels - Part 3: Thermoplastic Fittings for Pipes of Nominal Outside Diameter Less Than or Equal to 63mm |
|
BSI BS ISO 10998 |
Agricultural Wheeled Tractors - Steering Requirements |
|
BSI BS ISO 11450 |
Equipment for Harvesting and Conservation - Round Balers - Terminology and Commercial Specifications |
|
BSI BS ISO 11614 |
Reciprocating Internal Combustion Compression-Ignition Engines - Apparatus for Measurement of the Opacity and for Determination of the Light Absorption Coefficient of Exhaust Gas |
|
BSI BS ISO 11783-2 |
Tractors and machinery for agriculture and forestry Serial control and communications data network Part 2: Physical layer-CORR 14863: January 14, 2004; AMD 16555: September 29, 2006 |
|
BSI BS ISO 11783-7 |
Tractors and machinery for agriculture and forestry Serial control and communications data network Part 7: Implement messages application layer |
|
BSI BS ISO 11787 |
Machinery for Agriculture and Forestry - Data Interchange Between Management Computer and Process Computers - Data Interchange Syntax (E) |
|
BSI BS ISO 12003-2 |
Agricultural and forestry tractors Narrow-track wheeled tractors Part 2: Rear-mounted roll-over protective structures |
|
BSI BS ISO 1206 |
Rolling Bearings - Needle Roller Bearings, Dimension Series 48, 49 and 69 - Boundary Dimensions and Tolerances-Supersedes BS 5773-1: 1983; |
|
BSI BS ISO 12097-3 |
Road vehicles Airbag components Part 3: Testing of inflator assemblies |
|
BSI BS ISO 12353-2 |
Road vehicles Traffic accident analysis Part 2: Guidelines for the use of impact severity measures |