|
ISO 10112 |
Damping Materials - Graphical Presentation of the Complex Modulus First Edition |
|
ISO 10471 |
Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term ultimate bending strain and the long-term ultimate relative ring deflection under wet conditions-First Edition |
|
ISO 10485 |
Cone Proof Load Test on Nuts First Edition |
|
ISO 10639 |
Plastics piping systems for pressure and non-pressure water supply Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin-First Edition |
|
ISO 10819 |
Mechanical Vibration and Shock - Hand-Arm Vibration - Method for the Measurement and Evaluation of the Vibration Transmissibility of Gloves at the Palm of the Hand First Edition |
|
ISO 14887 |
Sample Preparation - Dispersing Procedures for Powders in Liquids-First Edition |
|
ISO 15242-1 |
Rolling bearings Measuring methods for vibration Part 1: Fundamentals-First Edition |
|
ISO 15261 |
Vibration and shock generating systems Vocabulary-First Edition |
|
ISO 15876-1 AMD 1 |
Plastics piping systems for hot and cold water installations Polybutylene (PB) Part 1: General AMENDMENT 1-First Edition |
|
ISO 16063-12 |
Methods for the Calibration of Vibration and Shock Transducers - Part 12: Primary Vibration Calibration by the Reciprocity Method-First Edition |
|
ISO 16287 |
Plain bearings Thermoplastic bushes Dimensions and tolerances-First Edition |
|
ISO 17455 CORR 1 |
Plastics piping systems Multilayer pipes Determination of the oxygen permeability of the barrier pipe TECHNICAL CORRIGENDUM 1-First Edition |
|
ISO 18431-1 |
Mechanical vibration and shock - Signal processing Part 1: General introduction-First Edition |
|
ISO 2037 |
Stainless Steel Tubes for the Food Industry-Second Edition |
|
ISO 2232 |
Round Drawn Wire for General Purpose Non-Alloy Steel Wire Ropes and for Large Diameter Steel Wire Ropes - Specifications-Second Edition |
|
ISO 2591-1 |
Test Sieving - Part 1: Methods Using Test Sieves of Woven Wire Cloth and Perforated Metal Plate-First Edition |
|
ISO 3077 |
Short Link Chain for Lifting Purposes - Grade T, (Types T, DAT and DT), Fine Tolerance Hoist Chain-Third Edition |
|
ISO 3126 |
Plastics piping systems Plastics components Determination of dimensions-Second edition |
|
ISO 4382-1 |
Plain Bearings - Copper Alloys - Part 1: Cast Copper Alloys for Solid and Multilayer Thick- Walled Plain Bearings Second Edition |
|
ISO 4392-1 |
Hydraulic Fluid Power - Determination of Characteristics of Motors - Part 1: At Constant Low Speed and at Constant Pressure-Third Edition |
|
ISO 4422-1 |
Pipes and Fittings Made of Unplasticized Poly(Vinyl Chloride) (PVC-U) for Water Supply - Specifications - Part 1: General-First Edition; Supersedes ISO 4422: 1990 |
|
ISO 4422-5 |
Pipes and Fittings Made of Unplasticized Poly(Vinyl Chloride) (PVC-U) for Water Supply - Specifications - Part 5: Fitness for Purpose of the System-First Edition; Supersedes ISO 4422: 1990 |
|
ISO 4766 |
Slotted Set Screws with Flat Point First Edition; (NZS/ISO 4766: 1983) |
|
ISO 5347-12 |
Methods for the Calibration of Vibration and Shock Pick-Ups - Part 12: Testing of Transverse Shock Sensitivity First Edition |
|
ISO 5597 |
Hydraulic Fluid Power - Cylinders - Housings for Piston and Rod Seals in Reciprocating Applications - Dimensions and Tolerances First Edition |
|
ISO 6022 |
Hydraulic fluid power Mounting dimensions for single rod cylinders, 25 MPa (250 bar) series-Second Edition; Supersedes ISO 8137: 1986 |
|
ISO 6259-3 |
Thermoplastics Pipes - Determination of Tensile Properties - Part 3: Polyolefin Pipes-First Edition |
|
ISO 6263 |
Hydraulic Fluid Power - Compensated Flow-Control Valves - Mounting Surfaces-Second Edition |
|
ISO 6264 |
Hydraulic Fluid Power - Pressure-Relief Valves - Mounting Surfaces-Second Edition |
|
ISO 6525 |
Plain Bearings - Ring Type Thrust Washers Made from Strip - Dimensions and Tolerances First Edition |
|
ISO 6897 |
Guidelines for the Evaluation of the Response of Occupants of Fixed Structures, Especially Buildings and Off-Shore Structures, to Low-Frequency Horizontal Motion (0,063 to 1 Hz) First Edition |
|
ISO 7046-2 |
Cross Recessed Countersunk Flat Head Screws (Common Head Style) - Grade A - Part 2: Steel of Property Class 8.8, Stainless Steel and Non-Ferrous Metals First Edition; (CEN EN ISO 7046-2: 1994) |
|
ISO 7425-1 |
Hydraulic Fluid Power - Housings for Elastomer-Energized, Plastic-Faced Seals - Dimensions and Tolerances - Part 1: Piston Seal Housings First Edition |
|
ISO 8179-1 |
Ductile iron pipes External zinc-based coating Part 1: Metallic zinc with finishing layer-Second Edition |
|
ISO 8179-2 |
Ductile Iron Pipes - External Zinc Coating - Part 2: Zinc Rich Paint with Finishing Layer First Edition; |
|
ISO 8283-1 |
Plastics Pipes and Fittings - Dimensions of Sockets and Spigots for Discharge Systems Inside Buildings - Part 1: Unplasticized Poly(Vinyl Chloride) (PVC-U) and Chlorinated Poly(Vinyl Chloride) (PVC-C) First Edition |
|
ISO 8737 |
Taper Pins with External Thread, Unhardened First Edition |
|
ISO 8740 |
Grooved Pins - Full-Length Parallel Grooved, with Chamfer-Second Edition |
|
ISO 9276-5 |
Representation of results of particle size analysis - Part 5: Methods of calculation relating to particle size analyses using logarithmic normal probability distribution-First Edition |
|
ISO TR 10657 |
Explanatory Notes on ISO 76 First Edition |
|
ISO TS 13762 |
Particle Size Analysis - Small Angle X-ray Scattering Method-First Edition |
|
ISO 1051 |
Rivet Shank Diameters-First Edition; Cancels and Replaces ISO Recommendation R 1051: 1969 |
|
ISO 10803 |
Design Method for Ductile Iron Pipes-First Edition |
|
ISO 10813-1 CORR 1 |
Vibration generating machines Guidance for selection Part 1: Equipment for environmental testing TECHNICAL CORRIGENDUM 1-First Edition |
|
ISO 11170 |
Hydraulic fluid power Filter elements Sequence of tests for verifying performance characteristics-Second edition |
|
ISO 113 |
Rolling Bearings - Plummer Block Housings - Boundary Dimensions-Second Edition |
|
ISO 12043 |
Rolling Bearings - Single-Row Cylindrical Roller Bearings - Chamfer Dimensions for Loose Rib and Non-Rib Sides-Second Edition |
|
ISO 12125 |
Prevailing Torque Type Hexagon Nuts with Flange (with Non-Metallic Insert) with Metric Fine Pitch Thread - Product Grades A and B-First Edition |
|
ISO 12130-3 |
Plain Bearings - Hydrodynamic Plain Tilting Pad Thrust Bearings Under Steady-State Conditions - Part 3:Guide Values for the Calculation of Tilting Pad Thrust Bearings-First Edition |
|
ISO 12131-1 |
Plain Bearings - Hydrodynamic Plain Thrust Pad Bearings Under Steady-State Conditions Part 1: Calculation of Thrust Pad Bearings-First Edition |
|
ISO 12238 |
Pneumatic Fluid Power - Directional Control Valves - Measurement of Shifting Time-First Edition |
|
ISO 13090-1 |
Mechanical Vibration and Shock - Guidance on Safety Aspects of Tests and Experiments with People - Part 1: Exposure to Whole-Body Mechanical Vibration and Repeated Shock-First Edition |
|
ISO 13322-1 |
Particle size analysis Image analysis methods Part 1: Static image analysis methods-First Edition |
|
ISO 14584 |
Hexalobular Socket Raised Countersunk Head Screws-First Edition |
|
ISO 14828 |
Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term specific ring relaxation stiffness under wet conditions and calculation of the wet relaxation factor-First Edition |
|
ISO 1483 |
Slotted Raised Countersunk (Oval) Head Tapping Screws (Common Head Style)-First Edition; CEN EN ISO 1483: 1994; AS/NZS 4405: 1996 |
|
ISO 15243 |
Rolling bearings Damage and failures Terms, characteristics and causes-First Edition |
|
ISO 15465 |
Pipework Stripwound metal hoses and hose assemblies-First Edition; Replaces ISO 7657:1995; ISO 7658:1984; ISO 8444:1985; ISO 8445:1995; ISO 8446:1995; ISO 8447:1986; ISO 8448:1986; ISO 8449:1995; ISO 8450:1986 |
|
ISO 15494 |
Plastics Piping Systems for Industrial Applications - Polybutene (PB), Polyethylene (PE) and Polypropylene (PP) - Specifications for Components and the System - Metric Series-First Edition; Corrected version: 2/01/2004 |
|
ISO 16434 |
Earthquake- and Subsidence-Resistant Design of Ductile Iron Pipelines-First Edition |
|
ISO 16589-3 |
Rotary Shaft Lip-Type Seals Incorporating Thermoplastic Sealing Elements - Part 3: Storage, Handling and Installation-First Edition |
|
ISO 16871 |
Plastics piping and ducting systems Plastics pipes and fittings Method for exposure to direct (natural) weathering-First Edition |
|
ISO 18437-2 |
Mechanical vibration and shock Characterization of the dynamic mechanical properties of visco-elastic materials Part 2: Resonance method-First Edition |
|
ISO 24033 |
Pipes made of raised-temperatureresistance polyethylene (PE-RT) Effect of time and temperature on the expected strength-First Edition |
|
ISO 2852 |
Stainless Steel Clamp Pipe Couplings for the Food Industry Second Edition |
|
ISO 2853 |
Stainless Steel Threaded Couplings for the Food Industry Second Edition |
|
ISO 2943 |
Hydraulic Fluid Power - Filter Elements - Verification of Material Compatibility with Fluids-Second Edition |
|
ISO 3213 |
Polypropylene (PP) Pipes - Effect of Time and Temperature on the Expected Strength Second Edition |
|
ISO 3321 |
Fluid Power Systems and Components - Cylinder Bores and Piston Rod Diameters - Inch Series First Edition |
|
ISO 3723 |
Hydraulic Fluid Power - Filter Elements - Method for End Load Test First Edition |
|
ISO 4386-2 |
Plain Bearings - Metallic Multilayer Plain Bearings - Part 2: Destructive Testing of Bond for Bearing Metal Layer Thicknesses Greater Than or Equal to 2 mm First Edition |
|
ISO 4412-2 |
Hydraulic Fluid Power - Test Code for Determination of Airborne Noise Levels - Part 2: Motors Second Edition |
|
ISO 4422-4 |
Pipes and Fittings Made of Unplasticized Poly(Vinyl Chloride) (PVC-U) for Water Supply - Specifications - Part 4: Valves and Ancillary Equipment-First Edition; Supersedes ISO 4422: 1990 |
|
ISO 4433-2 |
Thermoplastics Pipes - Resistance to Liquid Chemicals - Classification - Part 2: Polyolefin Pipes-First Edition; Replaces ISO 4433 |
|
ISO 4440-1 |
Thermoplastics Pipes and Fittings - Determination of Melt Mass-Flow Rate - Part 1: Test Method First Edition |
|
ISO 6020-2 |
Hydraulic Fluid Power - Mounting Dimensions for Single Rod Cylinders, 16 MPa (160 Bar) Series - Part 2: Compact Series-Third Edition |
|
ISO 6281 |
Plain bearings Testing under conditions of hydrodynamic and mixed lubrication in test rigs |
|
ISO 6432 |
Pneumatic Fluid Power - Single Rod Cylinders - 10 Bar (1 000 kPa) Series - Bores from 8 to 25 mm - Mounting Dimensions First Edition |
|
ISO 677 |
Straight Bevel Gears for General Engineering and Heavy Engineering - Basic Rack-First Edition |
|
ISO 6953-2 |
Pneumatic Fluid Power - Compressed Air Pressure Regulators and Filter-Regulators - Part 2: Test Methods to Determine the Main Characteristics to be Included in Literature from Suppliers-First Edition |
|
ISO 7048 |
Cross Recessed Cheese Head Screws-First Edition; Corrected and Reprinted 02/01/1999 |
|
ISO 7434 |
Slotted Set Screws with Cone Point First Edition; (NZS/ISO 7434: 1983) |
|
ISO 8132 |
Hydraulic fluid power Single rod cylinders, 16 MPa (160 bar) medium and 25 MPa (250 bar) series Mounting dimensions for accessories-Second Edition; Supersedes IS0 8132: 1996, ISO 6981: 1992 and ISO 6982: 1992 |
|
ISO 8180 |
Ductile iron pipelines Polyethylene sleeving for site application-Second Edition |
|
ISO 8626 |
Servo-Hydraulic Test Equipment for Generating Vibration - Method of Describing Characteristics First Edition |
|
ISO 8735 |
Parallel Pins with Internal Thread, of Hardened Steel and Martensitic Stainless Steel-Second Edition |
|
ISO 8745 |
Grooved Pins - Half-Length Taper Grooved-Second Edition |
|
ISO 9461 |
Hydraulic Fluid Power - Identification of Valve Ports, Subplates, Control Devices and Solenoids First Edition |
|
ISO 9852 |
Unplasticized poly(vinyl chloride) (PVC-U) pipes Dichloromethane resistance at specified temperature (DCMT) Test method-Second Edition |
|
ISO 9967 |
Thermoplastics pipes Determination of creep ratio-Second Edition |
|
ISO TR 13593 |
Enclosed gear drives for industrial applications-First Edition; Technical Corrigendum: 12/15/2005 |
|
ISO TR 14179-2 |
Gears - Thermal Capacity Part 2: Thermal Load-Carrying Capacity-First Edition |
|
ISO TR 18124 |
Plastics piping systems Multilayer M (metal) pipes Test method for strength of the weld line in the metal layer and bonding between layers by use of a cone-First Edition |
|
ISO TR 4191 |
Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Water Supply - Recommended Practice for Laying First Edition |
|
ISO TR 8646 |
Explanatory Notes on ISO 281/1-1977 First Edition |
|
ISO TS 7024 |
Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings Thermoplastics Recommended practice for installation-First Edition; Supersedes ISO TR 7024 |
|
ISO 10767-3 |
Hydraulic Fluid Power - Determination of Pressure Ripple Levels Generated in Systems and Components - Part 3: Method for Motors-First Edition |
|
ISO 10770-1 |
Hydraulic Fluid Power - Electrically Modulated Hydraulic Control Valves - Part 1: Test Methods for Four-Way Directional Flow Control Valves-First Edition; Together with ISO 10770-2, it Cancels and Replaces ISO 6404: 1985 |
|
ISO 10804-1 |
Restrained Joint Systems for Ductile Iron Pipelines - Part 1: Design Rules and Type Testing-First Edition |
|
ISO 1129 |
Steel Tubes for Boilers, Superheaters and Heat Exchangers - Dimensions, Tolerances and Conventional Masses per Unit Length-Second Edition |
|
ISO 11922-1 |
Thermoplastics Pipes for the Conveyance of Fluids - Dimensions and Tolerances - Part 1: Metric Series-First Edition; Together with ISO 11922-2, it Cancels and Replaces ISO 3606: 1976, ISO 3607: 1977, ISO 3608: 1976 and ISO 3609:1977 |
|
ISO 1224-1 |
Rolling bearings Instrument precision bearings Part 1: Boundary dimensions, tolerances and characteristics of metric series bearings-First Edition |
|
ISO 1224-2 |
Rolling bearings Instrument precision bearings Part 2: Boundary dimensions, tolerances and characteristics of inch series bearings-FIRST EDITION |
|
ISO 12302 |
Plain Bearings - Quality Characteristics - Statistical Process Control (SPC) First Edition |
|
ISO 12308 |
Plain Bearings - Quality Assurance - Sample Types - Definitions, Applications and Testing First Edition |
|
ISO 13924 |
Plastics Pipes and Fittings - Bending-Tensile Cycle Test for PE/Metal Transition Fittings, PE Tapping Tees and PE Branch Saddles-First Edition |
|
ISO 14589 |
Blind Rivets - Mechanical Testing-First Edition |
|
ISO 15407-2 |
Pneumatic fluid power Five-port directional control valves, sizes 18 mm and 26 mm Part 2: Mounting interface surfaces with optional electrical connector-First Edition |
|
ISO 15901-3 |
Pore size distribution and porosity of solid materials by mercury porosimetry and gas adsorption Part 3: Analysis of micropores by gas adsorption-First edition |
|
ISO 16136 |
Industrial valves Butterfly valves of thermoplastics materials-First Edition |
|
ISO 16422 |
Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure Specifications-First Edition |
|
ISO 16589-1 |
Rotary Shaft Lip-Type Seals Incorporating Thermoplastic Sealing Elements - Part 1: Nominal Dimensions and Tolerances-First Edition |
|
ISO 16860 |
Hydraulic fluid power Filters Test method for differential pressure devices-First Edition |
|
ISO 16874 |
Hydraulic fluid power Identification of manifold assemblies and their components-First Edition |
|
ISO 18437-3 |
Mechanical vibration and shock Characterization of the dynamic mechanical properties of visco-elastic materials Part 3: Cantilever shear beam method-First Edition |
|
ISO 2048 |
Double-Socket Fittings for Unplasticized Poly(Vinyl Chloride) (PVC-U) Pressure Pipes with Elastic Sealing Ring Type Joints - Minimum Depths of Engagement-Second Edition |
|
ISO 21287 |
Pneumatic fluid power Cylinders Compact cylinders, 1 000 kPa (10 bar) series, bores from 20 mm to 100 mm-First Edition |
|
ISO 2308 |
Hooks for Lifting Freight Containers of up to 30 Tonnes Capacity - Basic Requirements-First Edition |
|
ISO 246 |
Rolling bearings Cylindrical roller bearings, separate thrust collars Boundary dimensions-Third Edition |
|
ISO 264 |
Unplasticized Polyvinyl Chloride (PVC) Fittings with Plain Sockets for Pipes under Pressure - Laying Length - Metric Series-First Edition; Addendum 1-1982 |
|
ISO 2701 |
Drawn Wire for General Purpose Non-Alloy Steel Wire Ropes - Terms of Acceptance First Edition |
|
ISO 3501 |
Assembled Joints Between Fittings and Polyethylene (PE) Pressure Pipes - Test of Resistance to Pull out First Edition |
|
ISO 3503 |
Assembled Joints Between Fittings and Polyethylene (PE) Pressure Pipes - Test of Leakproofness Under Internal Pressure When Subjected to Bending First Edition |
|
ISO 3530 |
Vacuum Technology - Mass Spectrometer-Type Leak-Detector Calibration First Edition |
|
ISO 3661 |
End-Suction Centrifugal Pumps - Baseplate and Installation Dimensions First Edition; (CEN EN 23661: 1993) |
|
ISO 4065 |
Thermoplastic Pipes - Universal Wall Thickness Table-Second Edition |
|
ISO 4412-3 |
Hydraulic Fluid Power - Test Code for Determination of Airborne Noise Levels - Part 3: Pumps - Method Using a Parallelepiped Microphone Array First Edition |
|
ISO 5252 |
Steel Tubes - Tolerance Systems Second Edition |
|
ISO 559 |
Steel Tubes for Water and Sewage-Second Edition |
|
ISO 6070 |
Auxiliary tables for vibration generators Methods of describing equipment characteristics-First Edition; Technical Corrigendum 1: 09/15/2006 |
|
ISO 6953-1 |
Pneumatic Fluid Power - Compressed Air Pressure Regulators and Filter-Regulators - Part 1: Main Characteristics to Be Included in Literature from Suppliers and Product-Marking Requirements-Second Edition; Corrigendum: 4/1/2006 |
|
ISO 7046-1 |
Countersunk Flat Head Screws (Common Head Style) with Type H or Type Z Cross Recess - Product Grade A - Part 1: Steel of Property Class 4.8-First Edition |
|
ISO 7181 |
Hydraulic Fluid Power - Cylinders - Bore and Rod Area Ratios Second Edition |
|
ISO 727-2 |
Fittings made from unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C) or acrylonitrile/butadiene/styrene (ABS) with plain sockets for pipes under pressure Part 2: Inch-based series-Second edition |
|
ISO 7417 |
Hexagon Nuts for Structural Bolting - Style 2, Hot-Dip Galvanized (Oversize Tapped) - Product Grade A - Property Class 9 First Edition |
|
ISO 7719 |
Prevailing Torque Type All-Metal Hexagon Nuts, Style 1 - Property Classes 5, 8 and 10-Second Edition |
|
ISO 7745 |
Hydraulic Fluid Power - Fire-Resistant (FR) Fluids - Guidelines for Use First Edition |
|
ISO 7863 |
Height Setting Micrometers and Riser Blocks First Edition |
|
ISO 8133 |
Hydraulic fluid power Single rod cylinders, 16 MPa (160 bar) compact series Mounting dimensions for accessories-Second Edition; Supersedes ISO 6982: 1995 and ISO 8138: 1998 |
|
ISO 8770 |
Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings Polyethylene (PE)-Second Edition |
|
ISO 8778 |
Pneumatic Fluid Power - Standard Reference Atmosphere-Second Edition |
|
ISO 8793 |
Steel Wire Ropes - Ferrule-Secured Eye Terminations First Edition |
|
ISO 9045 |
Industrial Screens and Screening - Vocabulary First Edition |
|
ISO 9095 |
Steel Tubes - Continuous Character Marking and Colour Coding for Material Identification First Edition |
|
ISO 9349 |
Preinsulated ductile iron pipeline systems-Second Edition |
|
ISO 9688 |
Mechanical Vibration and Shock - Analytical Methods of Assessing Shock Resistance of Mechanical Systems - Information Exchange Between Suppliers and Users of Analyses First Edition |
|
ISO TS 16799 |
Rolling Bearings - Dynamic Load Ratings and Rating Life - Discontinuities in the Calculating of Basic Dynamic Load Ratings-First Edition |
|
ISO TS 18226 |
Plastics pipes and fittings Reinforced thermoplastics pipe systems for the supply of gaseous fuels for pressures up to 4 MPa (40 bar)-First Edition |
|
ISO 10055 |
Mechanical Vibration - Vibration Testing Requirements for Shipboard Equipment and Machinery Components-First Edition |
|
ISO 10467 |
Plastics piping systems for pressure and non-pressure drainage and sewerage Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin-First Edition |
|
ISO 10815 |
Mechanical Vibration - Measurement of Vibration Generated Internally in Railway Tunnels by the Passage of Trains First Edition |
|
ISO 12131-2 |
Plain Bearings - Hydronamic Plain Thrust Pad Bearings under Steady-State Conditions Part 2: Functions for the Calculation of Thrust Pad Bearings-First Edition |
|
ISO 12230 |
Polybutene (PB) Pipes - Effect of Time and Temperature on the Expected Strength-First Edition |
|
ISO 13753 |
Mechanical Vibration and Shock - Hand-Arm Vibration - Method for Measuring the Vibration Transmissibility of Resilient Materials When Loaded by the Hand-Arm System-First Edition |
|
ISO 15241 |
Rolling bearings Symbols for quantities-First Edition |
|
ISO 15552 |
Pneumatic fluid power Cylinders with detachable mountings, 1 000 kPa (10 bar) series, bores from 32 mm to 320 mm Basic, mounting and accessories dimensions-First Edition |
|
ISO 16028 FDAM 1 |
Hydraulic fluid power - Flush-face type, quick-action couplings for use at pressures of 20 MPa (200 bar) to 31, 5 MPa (315 bar) - Specifications --First Edition; Amendment 1:9/20/2005 |
|
ISO 20998-1 |
Measurement and characterization of particles by acoustic methods Part 1: Concepts and procedures in ultrasonic attenuation spectroscopy-First Edition |
|
ISO 21358 |
Vacuum technology Right-angle valve Dimensions and interfaces for pneumatic actuator-First edition |
|
ISO 21669 |
Steel wire ropes Determination of rotational properties-First edition |
|
ISO 2861-1 |
Vacuum Technology - Quick-Release Couplings - Dimensions - Part I: Clamped Type First Edition |
|
ISO 2861-2 |
Vacuum Technology - Quick Release Couplings - Dimensions - Part 2: Screwed Type First Edition |
|
ISO 3245 |
Rolling bearings Needle roller bearings, drawn cup without inner ring Boundary dimensions and tolerances-Third Edition |
|
ISO 4393 |
Fluid Power Systems and Components - Cylinders - Basic Series of Piston Strokes First Edition |
|
ISO 4439 |
Unplasticized Polyvinyl Chloride (PVC) Pipes and Fittings - Determination and Specification of Density First Edition |
|
ISO 4782 |
Metal Wire for Industrial Wire Screens and Woven Wire Cloth Second Edition |
|
ISO 4863 |
Resilient Shaft Couplings - Information to Be Supplied by Users and Manufacturers First Edition |
|
ISO 5251 |
Stainless Steel Butt-Welding Fittings First Edition |
|
ISO 6002 |
Bolted Bonnet Steel Gate Valves First Edition |
|
ISO 6020-3 |
Hydraulic Fluid Power - Mounting Dimensions for Single Rod Cylinders, 16 MPa (160 Bar) Series - Part 3: Compact Series with Bores from 250 mm to 500 mm First Edition |
|
ISO 61340-4-4 |
Electrostatics Part 4-4: Standard test methods for specific applications Electrostatic classification of flexible intermediate bulk containers (FIBC)-First Edition |
|
ISO 727-1 |
Fittings Made From Unplasticized Poly(Vinyl Chloride) (PVC-U), Chlorinated Poly(Vinyl Chloride) (PVC-C) or Acrylonitrile/Butadiene/Styrene (ABS) With Plain Sockets for Pipes Under Pressure - Part 1: Metric Series-First Edition |
|
ISO 7368 |
Hydraulic Fluid Power - Two-Port Slip-In Cartridge Valves - Cavities First Edition-Supersedes NFPA/Fluid T3.5.45 |
|
ISO 7370 |
Glass Fibre Reinforced Thermosetting Plastics (GRP) Pipes and Fittings - Nominal Diameters, Specified Diameters and Standard Lengths-First Edition |
|
ISO 7789 |
Hydraulic fluid power Two-, three- and four-port screw-in cartridge valves Cavities-Second Edition |
|
ISO 7841 |
Automatic Steam Traps - Determination of Steam Loss - Test Methods First Edition |
|
ISO 7904-2 |
Plain Bearings - Symbols - Part 2: Applications First Edition |
|
ISO 8002 |
Mechanical Vibrations - Land Vehicles - Method for Reporting Measured Data First Edition |
|
ISO 8131 |
Hydraulic Fluid Power - Single Rod Cylinders, 16 MPa (160 Bar) Compact Series - Tolerances Second Edition |
|
ISO 8233 |
Thermoplastics Valves - Torque - Test Method First Edition; (Corrected and Reprinted - 1989) |
|
ISO 8746 |
Grooved Pins with Round Head-Second Edition |
|
ISO TR 13989-2 |
Calculation of Scuffing Load Capacity of Cylindrical, Bevel and Hypoid Gears - Part 2: Integral Temperature Method-First Edition |
|
ISO TR 16806 |
Pneumatic fluid power Cylinders Load capacity of pneumatic slides and their presentation method-First Edition |
|
ISO 10146 |
Crosslinked Polyethylene (PE-X) Pipes - Effect of Time and Temperature on the Expected Strength-First Edition |
|
ISO 10802 |
Ductile Iron Pipelines - Hydrostatic Testing After Installation First Edition |
|
ISO 1167-2 |
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 2: Preparation of pipe test pieces-First Edition; Together with ISO 1167-1 Supersedes ISO 1167: 1996 and Together with ISO 1167-3 Supersedes ISO 12092: 2000 |
|
ISO 12130-1 |
Plain Bearings - Hydrodynamic Plain Tilting Pad Thrust Bearings Under Steady-State Conditions - Part 1: Calculation of Tilting Pad Thrust Bearings-First Edition |
|
ISO 12130-2 |
Plain Bearings - Hydrodynamic Plain Tilting Pad Thrust Bearings Under Steady-State Conditions - Part 2: Functions for Calculation of Tilting Pad Thrust Bearings-First Edition |
|
ISO 12131-3 |
Plain Bearings - Hydrodynamic Plain Thrust Pad Bearings under Steady-State Conditions Part 3: Guide Values for the Calculation of Thrust Pad Bearings-First Edition |
|
ISO 12149 |
Bolted Bonnet Steel Globe Valves for General-Purpose Applications-First Edition |
|
ISO 12240-2 |
Spherical Plain Bearings - Part 2: Angular Contact Radial Spherical Plain Bearings-First Edition |
|
ISO 12303 |
Plain Bearings - Quality Characteristics - Calculation of Machine and Process Capabilities First Edition |
|
ISO 13761 |
Plastics Pipes and Fittings - Pressure Reduction Factors for Polyethylene Pipeline Systems for Use at Temperatures Above 20 Degrees C-First Edition |
|
ISO 13778 |
Plain Bearings - Quality Assurance of Thin-Walled Half Bearings - Selective Assembly of Bearings to Achieve a Narrow Clearance Range-First Edition |
|
ISO 13954 |
Plastics Pipes and Fittings - Peel Decohesion Test for Polyethylene (PE) Electrofusion Assemblies of Nominal Outside Diameter Greater Than or Equal to 90 mm-First Edition |
|
ISO 14585 |
Hexalobular Socket Pan Head Tapping Screws-First Edition; Technical Corrigendum 1: 05-15-2004 |
|
ISO 14837-1 |
Mechanical vibration - Ground-borne noise and vibration arising from rail systems - Part 1: General guidance-First Edition |
|
ISO 14839-1 |
Mechanical Vibration - Vibration of Rotating Machinery Equipped with Active Magnectic Bearings - Part 1: Vocabulary-First Edition |
|
ISO 15171-1 |
Connections for Fluid Power and General Use - Hydraulic Couplings for Diagnostic Purposes - Part 1: Coupling Not for Connection Under Pressure-First Edition |
|
ISO 15407-1 |
Pneumatic Fluid Power - Five-Port Directional Control Valves, Sizes 18 mm and 26 mm - Part 1: Mounting Interface Surfaces without Electrical Connector-First Edition |
|
ISO 15480 |
Hexagon Washer Head Drilling Screws with Tapping Screw Thread-First Edition |
|
ISO 15875-3 |
Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings-First Edition |
|
ISO 16137 |
Industrial valves Check valves of thermoplastics materials-First Edition |
|
ISO 17558 |
Steel wire ropes Socketing procedures Molten metal and resin socketing-First Edition; Supersedes ISO 7595: 1984 and ISO/TR 7596: 1982 |
|
ISO 2016 |
Capillary Solder Fittings for Copper Tubes - Assembly Dimensions and Tests-First Edition |
|
ISO 21360 |
Vacuum technology Standard methods for measuring vacuum-pump performance General description-First Edition |
|
ISO 23309 |
Hydraulic fluid power systems Assembled systems Methods of cleaning lines by flushing-First Edition |
|
ISO 2536 |
Unplasticized Polyvinyl Chloride (PVC) Pressure Pipes and Fittings, Metric Series - Dimensions of Flanges-First Edition |
|
ISO 265-1 |
Pipes and Fittings of Plastics Materials - Fittings for Domestic and Industrial Waste Pipes - Basic Dimensions: Metric Series - Part 1: Unplasticized Poly(Vinyl Chloride) (PVC-U)-First Edition |
|
ISO 3031 |
Roller Bearings - Thrust Needle Roller and Cage Assemblies, Thrust Washers - Boundary Dimensions and Tolerances-Third Edition |
|
ISO 3310-3 |
Test Sieves - Technical Requirements and Testing - Part 3: Test Sieves of Electroformed Sheets First Edition |
|
ISO 3724 |
Hydraulic fluid power - Filter elements - Determination of resistance to flow fatigue using particulate contaminant-Second Edition |
|
ISO 4179 |
Ductile iron pipes and fittings for pressure and non-pressure pipelines Cement mortar lining-Third Edition |
|
ISO 4399 |
Fluid Power Systems and Components - Connectors and Associated Components - Nominal Pressures Second Edition |
|
ISO 4422-3 |
Pipes and Fittings Made of Unplasticized Poly(Vinyl Chloride) (PVC-U) for Water Supply - Specifications - Part 3: Fittings and Joints-First Edition; Supersedes ISO 4422: 1990 |
|
ISO 5996 |
Cast Iron Gate Valves First Edition |
|
ISO 6259-2 |
Thermoplastics Pipes - Determination of Tensile Properties - Part 2: Pipes Made of Unplasticized Poly(Vinyl Chloride) (PVC-U), Chlorinated Poly(Vinyl Chloride) (PVC-C) and High-Impact Poly(Vinyl Chloride) (PVC-HI)-First Edition |
|
ISO 6993-1 |
Buried, high-impact poly(vinyl chloride) (PVC-HI) piping systems for the supply of gaseous fuels Part 1: Pipes for a maximum operating pressure of 1 bar (100 kPa)-First Edition; Together with ISO 6993-2 thru ISO 6993-4 replaces ISO 6993: 2001 |
|
ISO 7063 |
Rolling bearings Needle roller bearing track rollers Boundary dimensions and tolerances-Second Edition; Replaces ISO 6278 |
|
ISO 7148-2 |
Plain Bearings - Testing of the Tribological Behaviour of Bearing Materials - Part 2: Testing of Polymer-Based Bearing Materials-First Edition |
|
ISO 7414 |
Hexagon Nuts for Structural Bolting with Large Width Across Flats, Style 1 - Product Grade B - Property Class 10 First Edition |
|
ISO 7425-2 |
Hydraulic Fluid Power - Housings for Elastomer-Energized, Plastic-Faced Seals - Dimensions and Tolerances - Part 2: Rod Seal Housings First Edition |
|
ISO 7686 |
Plastics pipes and fittings - Determination of opacity-Second Edition |
|
ISO 8139 |
Pneumatic Fluid Power - Cylinders, 1 000 kPa (10 Bar) Series - Rod End Spherical Eyes - Mounting Dimensions Second Edition |
|
ISO 8283-2 |
Plastics Pipes and Fittings - Dimensions of Sockets and Spigots for Discharge Systems Inside Buildings - Part 2: Polyethylene (PE) First Edition |
|
ISO 8483 |
Glass-reinforced thermosetting plastics (GRP) pipes and fittings Test methods to prove the design of bolted flange joints-First Edition |
|
ISO 8512-1 |
Surface Plates - Part 1: Cast Iron First Edition |
|
ISO TR 10358 |
Plastics Pipes and Fittings - Combined Chemical-Resistance Classification Table First Edition; |
|
ISO TR 13989-1 |
Calculation of Scuffing Load Capacity of Cylindrical, Bevel and Hypoid Gears - Part 1: Flash Temperature Method-Fisrt Edition |
|
ISO TR 15403-2 |
Natural gas Natural gas for use as a compressed fuel for vehicles Part 2: Specification of the quality-First Edition |
|
ISO TR 16386 |
Impact of Changes in ISO Fluid Power Particle Counting - Contamination Control and Filter Test Standards-First Edition |
|
ISO 10099 |
Pneumatic Fluid Power - Cylinders - Final Examination and Acceptance Criteria-Second Edition |
|
ISO 10468 |
Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factor-First Edition |
|
ISO 10807 |
Pipework - Corrugated Flexible Metallic Hose Assemblies for the Protection of Electrical Cables in Explosive Atmospheres First Edition |
|
ISO 10945 |
Hydraulic Fluid Power - Gas-Loaded Accumulators - Dimensions of Gas Ports First Edition |
|
ISO 11414 |
Plastics Pipes and Fittings - Preparation of Polyethylene (PE) Pipe/Pipe or Pipe/ Fitting Test Piece Assemblies by Butt Fusion First Edition |
|
ISO 12076 |
Steel Wire Ropes - Determination of the Actual Modulus of Elasticity-First Edition |
|
ISO 13091-2 |
Mechanical vibration Vibrotactile perception thresholds for the assessment of nerve dysfunction Part 2: Analysis and interpretation of measurements at the fingertips-First Edition |
|
ISO 13317-2 |
Determination of Particle Size Distribution by Gravitational Liquid Sedimentation Methods - Part 2: Fixed Pipette Method-First Edition |
|
ISO 13317-3 |
Determination of Particle Size Distribution by Gravitational Liquid Sedimentation Methods - Part 3: X-Ray Gravitational Technique-First Edition |
|
ISO 13318-1 |
Determination of Particle Size Distribution by Centrifugal Liquid Sedimentation Methods - Part 1: General Principles and Guidelines-First Edition |
|
ISO 13477 |
Thermoplastics Pipes for the Conveyance of Fluids - Determination of Resistance to Rapid Crack Propagation (RCP) - Small-Scale Steady-State Test (S4 Test)-First Edition |
|
ISO 13783 |
Plastics Piping Systems - Unplasticized Poly(Vinyl Chloride) (PVC-U) End-Load-Bearing Double-Socket Joints - Test Method for Leaktightness and Strength While Subjected to Bending and Internal Pressure-First Edition |
|
ISO 13846 |
Plastic Piping Systems - End-Load-Bearing and Non-End-Load-Bearing Assemblies and Joints for Thermoplastics Pressure Piping - Test Method for Long-Term Leaktightness Under internal Water Pressure-First Edition |
|
ISO 13950 CORR 1 |
Plastics pipes and fittings Automatic recognition systems for electrofusion joints TECHNICAL CORRIGENDUM 1-First Edition |
|
ISO 14315 |
Industrial Wire Screens - Technical Requirements and Testing-First Edition |
|
ISO 14587 |
Hexalobular Socket Raised Conutersunk (Oval) Head Tapping Screws-First Edition |
|
ISO 14776-331 |
Information Technology Small Computer System Interface (SCSI) Part 331: Stream Commands (SSC) |
|
ISO 14963 |
Mechanical vibration and shock Guidelines for dynamic tests and investigations on bridges and viaducts-First Edition |
|
ISO 15086-1 |
Hydraulic Fluid Power - Determination of Fluid-Borne Noise Characteristics of Components and Systems - Part 1: Introduction-First Edition |
|
ISO 15482 |
Cross Recessed Countersunk Head Drilling Screws with Tapping Screw Thread-First Edition |
|
ISO 15853 |
Thermoplastics Materials - Preparation of Tubular Test Pieces for the Determination of the Hydrostatic Strength of Materials Used for Injection Moulding-First Edition |
|
ISO 15874-3 |
Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 3: Fittings-First Edition |
|
ISO 15876-3 |
Plastics piping systems for hot and cold water installations Polybutylene (PB) Part 3: Fittings-First Edition |
|
ISO 15877-2 |
Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 2: Pipes-First Edition |
|
ISO 15877-5 |
Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 5: Fitness for purpose of the system-First Edition |
|
ISO 15908 |
Adhesives for Thermoplastic Piping Systems - Test Method for the Determination of Thermal Stability of Adhesives-First Edition |
|
ISO 15975 |
Closed End Blind Rivets With Break Pull Mandrel and Protruding Head - AI/AIA-First Edition |
|
ISO 15982 |
Open End Blind Rivets with Break Pull Mandrel and Countersunk Head - AIA/AIA-First Edition |
|
ISO 16030 |
Pneumatic Fluid Power - Connections - Ports and Stud Ends-First Edition; Amendment 1: 4/1/2005 |
|
ISO 16139 |
Industrial valves Gate valves of thermoplastics materials-First Edition |
|
ISO 16584 |
Open End Blind Rivets with Break Pull Mandrel and Protruding Head - NiCu/St OR NiCu/SSt-First Edition |
|
ISO 18649 |
Mechanical vibration Evaluation of measurement results from dynamic tests and investigations on bridges-First Edition |
|
ISO 2262 |
General Purpose Thimbles for Use with Steel Wire Ropes - Specification-Second Edition |
|
ISO 2507-1 |
Thermoplastics Pipes and Fittings - Vicat Softening Temperature - Part 1: General Test Method-First Edition; Replaces ISO 2507 |
|
ISO 2507-2 |
Thermoplastics Pipes and Fittings - Vicat Softening Temperature - Part 2: Test Conditions for Unplasticized Poly(Vinyl Chloride) (PVC-U) or Chlorinated Poly(Vinyl Chloride) (PVC-C) Pipes and Fittings and for High Impact Resistance Poly(Vinyl Chloride) (PVC-HI) Pipes-First Edition; Replaces ISO 2507 |
|
ISO 2507-3 |
Thermoplastics Pipes and Fittings - Vicat Softening Temperature - Part 3: Test Conditions for Acrylonitrile/ Butadiene/Styrene (ABS) and Acrylonitrile/ Styrene/Acrylic Ester (ASA) Pipes and Fittings-First Edition |
|
ISO 2851 |
Stainless Steel Bends and Tees for the Food Industry-Second Edition |
|
ISO 3189-1 |
Sockets for Wire Ropes for General Purposes - Part 1: General Characteristics and Conditions of Acceptance-First Edition; Technical Corrigendum 1: 02/15/2002 |
|
ISO 3460 |
Unplasticized Polyvinyl Chloride (PVC) Pressure Pipes - Metric Series - Dimensions of Adapter for Backing Flange First Edition |
|
ISO 3514 |
Chlorinated Polyvinyl Chloride (CPVC) Pipes and Fittings - Specification and Determination of Density First Edition |
|
ISO 3603 |
Fittings for Unplasticized Polyvinyl Chloride (PVC) Pressure Pipes with Elastic Sealing Ring Type Joints - Pressure Test for Leakproofness First Edition |
|
ISO 4145 |
Non-Alloy Steel Fittings Threaded to ISO 7/1 Second Edition |
|
ISO 4392-3 |
Hydraulic Fluid Power - Determination of Characteristics of Motors - Part 3: At Constant Flow and at Constant Torque First Edition |
|
ISO 4433-3 |
Thermoplastics Pipes - Resistance to Liquid Chemicals - Classification - Part 3: Unplasticized Poly(Vinyl Chloride) (PVC-U), High-Impact Poly(Vinyl Chloride) (PVC-HI) and Chlorinated Poly(Vinyl Chloride) (PVC-C) Pipes-First Edition; Replaces ISO 4433 |
|
ISO 4434 |
Unplasticized Polyvinyl Chloride (PVC) Adaptor Fittings for Pipes Under Pressure - Laying Length and Size of Threads - Metric Series First Edition |
|
ISO 4440-2 |
Thermoplastics Pipes and Fittings - Determination of Melt Mass-Flow Rate - Part 2: Test Conditions First Edition |
|
ISO 5784-2 |
Fluid Power Systems and Components - Fluid Logic Circuits - Part 2: Symbols for Supply and Exhausts as Related to Logic Symbols First Edition |
|
ISO 580 |
Plastics piping and ducting systems Injection-moulded thermoplastics fittings Methods for visually assessing the effects of heating-Third Edition |
|
ISO 6280 |
Plain Bearings - Requirements on Backings for Thick-Walled Multilayer Bearings First Edition |
|
ISO 6282 |
Plain Bearings - Metallic Thin-Walled Half Bearings - Determination of the Conductivity 0,01-Limit First Edition |
|
ISO 6455 |
Unplasticized Polyvinyl Chloride (PVC) Fittings with Elastic Sealing Ring Type Joints for Pipes Under Pressure - Dimensions of Laying Lengths - Metric Series First Edition |
|
ISO 6537 |
Pneumatic Fluid Power Systems - Cylinder Barrels - Requirements for Non-Ferrous Metallic Tubes First Edition |
|
ISO 6993-2 |
Buried, high-impact poly(vinyl chloride) (PVC-HI) piping systems for the supply of gaseous fuels Part 2: Fittings for a maximum operating pressure of 200 mbar (20 kPa)-First Edition; Together with ISO 6993-1, ISO 6993-3 and ISO 6993-4: 2006 replaces ISO 6993: 2001 |
|
ISO 7146 |
Plain Bearings - Terms, Characteristics and Causes of Damage and Changes in Appearance First Edition |
|
ISO 7279 |
Polypropylene (PP) Fittings for Pipes Under Pressure - Sockets for Fusion Using Heated Tools - Metric Series - Dimensions of Sockets First Edition |
|
ISO 7413 |
Hexagon Nuts for Structural Bolting, Style 1, Hot-Dip Galvanized (Oversize Tapped) - Product Grades A and B - Property Classes 5, 6 and 8 First Edition |
|
ISO 7435 |
Slotted Set Screws with Long Dog Point First Edition; (NZS/ISO 7435: 1983) |
|
ISO 7510 |
Plastics Piping Systems - Glass-Reinforced Plastics (GRP) Components - Determination of the Amounts of Constituents Using the Gravimetric Method-First Edition |
|
ISO 7684 |
Plastics Piping Systems - Glass-Reinforced Thermosetting Plastics (GRP) Pipes - Determination of the Creep Factor under Dry Conditions-First Edition |
|
ISO 7685 |
Plastics Piping Systems - Glass-Reinforced Thermosetting Plastics (GRP) Pipes - Determination of Initial Specific Ring Stiffness-First Edition |
|
ISO 7805-2 |
Industrial Plate Screens - Part 2: Thickness Below 3 mm First Edition |
|
ISO 7806 |
Industrial Plate Screens - Codification for Designating Perforations First Edition |
|
ISO 7905-1 |
Plain Bearings - Bearing Fatigue - Part 1: Plain Bearings in Test Rigs and in Applications Under Conditions of Hydrodynamic Lubrication First Edition |
|
ISO 7905-3 |
Plain Bearings - Bearing Fatigue - Part 3: Test on Plain Strips of a Metallic Multilayer Bearing Material First Edition; (Corrected and Reprinted - 1996) |
|
ISO 8242 |
Polypropylene (PP) Valves for Pipes Under Pressure - Basic Dimensions - Metric Series First Edition |
|
ISO 8283-3 |
Plastics Pipes and Fittings - Dimensions of Sockets and Spigots for Discharge Systems Inside Buildings - Part 3: Polypropylene (PP) First Edition |
|
ISO 8361-2 |
Thermoplastics Pipes and Fittings - Water Absorption - Part 2: Test Conditions for Unplasticized Poly(Vinyl Chloride) (PVC-U) Pipes and Fittings First Edition |
|
ISO 8521 |
Plastics Piping Systems - Glass-Reinforced Thermosetting Plastics (GRP) Pipes - Determination of the Apparent Initial Circumferential Tensile Strength-First Edition |
|
ISO 8572 |
Pipes and Fittings Made of Glass-Reinforced Thermosetting Plastics (GRP) - Definitions of Terms Relating to Pressure, Including Relationships Between Them, and Terms for Installation and Jointing First Edition |