| SAE AMS-H-6875A | Heat Treatment of Steel Raw Materials-Should Be Used Instead of MIL-H-6875, Which Was Cancelled on 2 February 1999 |
| SAE AMS 2700B | Passivation of Corrosion Resistant Steels |
| SAE AMS-QQ-S-763B | Steel, Corrosion Resistant, Bars, Wire, Shapes, and Forgings |
| SAE AMS 5643Q | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Tubing, and Rings 16Cr - 4.0Ni - 0.30Cb - 4.0Cu Solution Heat Treated, Precipitation Hardenable-UNS S17400 |
| SAE AMS-QQ-P-416B | Plating, Cadmium (Electrodeposited) |
| SAE AMS 2770H | Heat Treatment of Wrought Aluminum Alloy Parts |
| SAE AMS 5659L | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Rings, and Extrusions 15Cr - 4.5Ni - 0.30CB (Nb) - 3.5Cu Consumable Electrode Melted Solution Heat Treated, Precipitation Hardenable (Composition similar to UNS S15500) |
| SAE AMS-QQ-A-250/11 | Aluminum Alloy 6061, Plate and Sheet-UNS A96061 |
| SAE AMS-DTL-23053/5 | Insulation Sleeving, Electrical, Heat Shrinkable, Polyolefin, Flexible, Crosslinked-FSC 5970; Should Be Used Instead of MIL-DTL-23053/5C, Which Was Cancelled on 16 September 1999 |
| SAE AMS-DTL-23053 | Insulation Sleeving, Electrical, Heat Shrinkable, General Specification for-FSC 5970; Should Be Used Instead of MIL-DTL-23053E, Which Was Cancelled on 16 September 1999 |
| SAE AMS-QQ-A-250A | Aluminum and Aluminum Alloy, Plate and Sheet General Specification for |
| SAE AMS 4928R | Titanium Alloy Bars, Wire, Forgings, Rings, and Drawn Shapes 6Al - 4V Annealed-UNS R56400 |
| SAE AMS 5662M | Nickel Alloy, Corrosion and Heat Resistant, Bars, Forgings, and Rings 52.5Ni - 19Cr - 3.0Mo - 5.1Cb - 0.90Ti - 0.50Al - 18Fe Consumable Electrode or Vacuum Induction Melted 1775 Degrees F (968 Degrees C) Solution Heat Treated, Precipitation Hardenable-UNS N07718 |
| SAE AMS 2759/3D | Heat Treatment Precipitation-Hardening Corrosion-Resistant and Maraging Steel Parts |
| SAE AMS 4911L | Titanium Alloy, Sheet, Strip, and Plate 6AI - 4V Annealed-UNS R56400 |
| SAE AMS 5731L | Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Tubing, and Rings 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V Consumable Electrode Melted, 1800 °F (982 °C) Solution Heat Treated-UNS S66286 |
| SAE AMS-S-8802B | Sealing Compound, Temperature Resistant, Integral Fuel Tanks and Fuel Cell Cavities, High Adhesion |
| SAE AMS-QQ-A-250/12 | Aluminum Alloy 7075, Plate and Sheet-A97075 |
| SAE AMS 2750D | (R) Pyrometry |
| SAE AMS 5510R | Steel, Corrosion and Heat Resistant, Sheet, Strip and Plate 18Cr - 10.5Ni - 0.40Ti (SAE 30321) Solution Heat Treated-UNS S32100 |
| SAE AMS 2759/1D | Heat Treatment of Carbon and Low-Alloy Steel Parts Minimum Tensile Strength Below 220 ksi (1517 MPa) |
| SAE AMS 5737P | Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, and Tubing 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V Consumable Electrode Melted 1650 Degrees F (899 Degrees C) Solution and Precipitation Heat Treated-UNS S66286 |
| SAE AMS 2175 | Castings, Classification and Inspection of-Superseding AMS-STD-2175 |
| SAE AMS-QQ-A-200/11 | Aluminum Alloy 7075, Bar, Rod, Shapes, Tube, and Wire, Extruded-UNS A97075 |
| SAE AMS-S-6758A | Steel, Chrome-Molybdenum (4130) Bars and Reforging Stock (Aircraft Quality) |
| SAE AMS 7276G | Rings, Sealing, Fluorocarbon (FKM) Rubber High-Temperature-Fluid Resistant Low Compression Set 70 to 80 |
| SAE AMS 5629E | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Rings, and Extrusions 13Cr - 8.0Ni - 2.2Mo - 1.1Al Vacuum Induction Plus Consumable Electrode Melted Solution Heat Treated, Precipitation Hardenable-UNS S13800 |
| SAE AMS-QQ-A-200/8 | Aluminum Alloy 6061, Bar, Rod, Shapes, Tube, and Wire, Extruded-UNS A96061 |
| SAE AMS-QQ-C-320B | Chromium Plating (Electrodeposited) |
| SAE AMS-STD-2154 | Inspection, Ultrasonic, Wrought Metals, Process for |
| SAE AMS-QQ-A-250/4A | Aluminum Alloy 2024, Plate and Sheet-UNS A92024 |
| SAE AMS 6415S | Steel, Bars, Forgings, and Tubing 0.80Cr - 1.8Ni - 0.25Mo (0.38 - 0.43C) (SAE 4340)-UNS G43406 |
| SAE AMS 6414K | Steel, Bars, Forgings, and Tubing 0.80Cr - 1.8Ni - 0.25Mo (0.38 - 0.43C) (SAE 4340) Vacuum Consumable Electrode Remelted-UNS G43406 |
| SAE AMS 2404E | Plating, Electroless Nickel |
| SAE AMS-QQ-N-290A | Nickel Plating (Electrodeposited) |
| SAE AMS 4050H | Aluminum Alloy, Plate 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (7050-T7451) Solution Heat Treated, Stress Relieved, and Overaged-UNS A97050 |
| SAE AMS-QQ-A-250/5A | Aluminum Alloy Alclad 2024, Plate and Sheet-UNS A82024 |
| SAE AMS 2772E | Heat Treatment of Aluminum Alloy Raw Materials |
| SAE AMS-DTL-22499 | Shim Stock, Laminated |
| SAE AMS-C-26074B | Electroless Nickel Coatings |
| SAE AMS 5732J | Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Tubing, and Rings 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V Consumable Electrode Melted 1800 Degrees F (982 Degrees C) Solution and Precipitation Heat Treated-UNS S66286 |
| SAE AMS-S-5000A | Steel, Chrome-Nickel-Molybdenum (E4340) Bars and Reforging Stock |
| SAE AMS 2658B | Hardness and Conductivity Inspection of Wrought Aluminum Alloy Parts-: 2006 |
| SAE AMS 6322N | Steel Bars, Forgings, and Rings 0.50Cr - 0.55Ni - 0.25Mo (0.38 - 0.43C) (SAE 8740)-UNS G87400 |
| SAE AMS-S-13165A | Shot Peening of Metal Parts |
| SAE AMS 2759D | Heat Treatment of Steel Parts General Requirements |
| SAE AMS-W-6858B | Welding, Resistance: Spot and Seam |
| SAE AMS 4640G | Aluminum Bronze, Bars, Rods, Shapes, Tubes, and Forgings 81.5Cu - 10.0Al - 4.8Ni - 3.0Fe Drawn and Stress Relieved (HR50) or Temper Annealed (TQ50)-Composition similar to UNS C63000 |
| SAE AMS 2430M | (R) Shot Peening, Automatic |
| SAE AMS-A-21180A | Aluminum-Alloy Castings, High Strength AREA MECA-Superseding AMS 3894/2A |
| SAE AMS 5596K | Nickel Alloy, Corrosion and Heat-Resistant, Sheet, Strip, Foil and Plate 52.5Ni - 19Cr - 3.0Mo - 5.1Cb (Nb) - 0.90Ti - 0.50Al - 18Fe Consumable Electrode Remelted or Vacuum Induction Melted 1775 °F (968 °C) Solution Heat Treated-UNS N07718 |
| SAE AMS 2644E | Inspection Material, Penetrant |
| SAE AMS 5599G | Nickel Alloy, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 62Ni - 21.5Cr - 9.0Mo - 3.7 Cb (Nb) Solution Heat Treated-UNS N06625 |
| SAE AMS 5513H | Steel, Corrosion Resistant, Sheet, Strip, and Plate 19Cr - 9.2Ni (SAE 30304) Solution Heat Treated-UNS S30400 |
| SAE AMS-QQ-A-225/8A | Aluminum Alloy 6061, Bar, Rod, and Wire, and Special Shapes; Rolled, Drawn, or Cold Finished-A96061 |
| SAE AMS-QQ-A-225/9 | Aluminum Alloy 7075, Bar, Rod, Wire, and Special Shapes; Rolled, Drawn, or Cold Finished |
| SAE AMS 5663M | Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 52.5Ni - 19Cr - 3.0Mo - 5.1Cb - 0.90Ti - 0.50Al - 18Fe Consumable Electrode or Vacuum Induction Melted 1775 Degrees F (968 Degrees C) Solution and Precipitation Heat Treated-UNS N07718 |
| SAE AMS 5604E | Steel, Corrosion Resistant, Sheet, Strip, and Plate 16.5Cr - 4.0Ni - 4.0Cu - 0.30Cb Solution Heat Treated, Precipitation Hardenable-UNS S17400 |
| SAE AMS 5528H | Steel, Corrosion-Resistant, Sheet, Strip, and Plate 17Cr - 7.1Ni - 1.1Al Solution Heat Treated, Precipitation Hardenable |
| SAE AMS-QQ-A-225/6A | Aluminum Alloy, 2024, Bar, Rod, and Wire; Rolled, Drawn, or Cold Finished-A92024 |
| SAE AMS-A-22771A | Aluminum Alloy Forgings, Heat Treated |
| SAE AMS-QQ-A-367A | Aluminum Alloy Forgings |
| SAE AMS-P-83461 | Packing, Preformed, Petroleum Hydralic Fluid Resistant, Improved Performance at 275 Degrees F (135 Degrees C) |
| SAE AMS-WW-T-700/6A | Tube, Aluminum Alloy, Drawn, Seamless, 6061 |
| SAE AMS 5678F | Steel, Corrosion Resistant, Wire 17Cr - 7.1Ni - 1.1Al Cold Drawn, Precipitation-Hardenable-UNS S17700 |
| SAE AMS-QQ-A-200B | Aluminum Alloy, Bar, Rod, Shapes, Structural Shapes, Tube, and Wire, Extruded: General Specification for |
| SAE AMS 6350K | Steel Sheet, Strip, and Plate 0.95Cr - 0.20Mo (0.28 - 0.33C) (SAE 4130)-UNS G41300 |
| SAE AMS 5640U | Steel, Corrosion-Resistant, Bars, Wire, and Forgings 18Cr - 9.0Ni Free Machining-UNS S30300 (Type 1); UNS S30323 (Type 2); UNS S30310 (Type 3) |
| SAE AMS-P-83461/1A | Packing, Preformed, Petroleum Hydraulic Fluid Resistant Improved Performance at 275°F (135°C) Sizes and Tolerances |
| SAE AMS-QQ-A-250/13 | Aluminum Alloy Alclad 7075, Plate and Sheet |
| SAE AMS 5666F | Nickel Alloy, Corrosion and Heat Resistant, Bars, Forgings, Extrusions, and Rings 62Ni - 21.5Cr - 9.0Mo - 3.65 (Cb+Ta) Annealed-UNS N06625 |
| SAE AMS 5639H | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Tubing, and Rings 19Cr - 10Ni Solution Heat Treated-UNS S30400 |
| SAE AMS-QQ-A-200/3 | Aluminum Alloy 2024, Bar, Rod, Shapes, Tube, and Wire, Extruded-UNS A92024 |
| SAE AMS 5646M | Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Tubing, and Rings 18Cr - 11 Ni - 0.60Cb (SAE 30347) Solution Heat Treated-UNS S34700 |
| SAE AMS 6345B | Steel, Sheet, Strip, and Plate 0.95Cr - 0.20Mo (0.28 - 0.33C) (SAE 4130) Normalized or Otherwise Heat Treated-UNS G41300 |
| SAE AMS 5525J | Steel, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V 1800 °F (982 °C) Solution Heat Treated-UNS S66286 |
| SAE AMS-C-9084 | Cloth, Glass, Finished, for Resin Laminates-FSC 8305; Should Be Used Instead of MIL-C-9084C, Which Was Cancelled on 10 September 1999 |
| SAE AMS 2403L | Plating, Nickel General Purpose |
| SAE AMS 5536M | Nickel Alloy, Corrosion and Heat Resistant, Sheet, Strip, and Plate 47.5Ni - 22Cr - 1.5Co - 9.0Mo - 0.60W - 18.5Fe Solution Heat Treated-UNS N06002 |
| SAE AMS 2242F | Tolerances Corrosion and Heat Resistant Steel, Iron Alloy, Titanium, and Titanium Alloy Sheet, Strip, and Plate |
| SAE AMS 2759/2D | Heat Treatment of Low-Alloy Steel Parts Minimum Tensile Strength 220 ksi (1517 MPa) and Higher |
| SAE AMS 3216G | Fluorocarbon (FKM) Rubber High-Temperature - Fluid Resistant Low Compression Set 70 to 80 |
| SAE AMS-H-81200A | Heat Treatment of Titanium and Titanium Alloys-Replaces MIL-H-81200 |
| SAE AMS 5516P | Steel, Corrosion-Resistant, Sheet, Strip, and Plate 18Cr - 9.0Ni (SAE 30302) Solution Heat Treated-UNS S30200 |
| SAE AMS-R-83485 | Rubber, Fluorocarbon Elastomer, Improved Performance at Low Temperatures |
| SAE AMS-QQ-A-250/8B | Aluminum Alloy 5052, Plate and Sheet-UNS A95052 |
| SAE AMS-QQ-A-225B | Aluminum and Aluminum Alloy, Bar, Rod, Wire, or Special Shapes; Rolled, Drawn, or Cold Finished; General Specification For |
| SAE AMS-R-83485/1 | Rubber, Fluorocarbon Elastomer, Improved Performance at Low Temperatures, O-Rings, Sizes and Tolerances-FSC 5330 |
| SAE AMS 5613R | Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Tubing, and Rings 12.5Cr (SAE 51410) Annealed-UNS S41000 |
| SAE AMS 2771C | Heat Treatment of Aluminum Alloy Castings |
| SAE AMS 6265M | Steel, Bars, Forgings, and Tubing 1.2Cr - 3.25Ni - 0.12Mo (0.07 - 0.13C) (SAE 9310) Vacuum Consumable Electrode Remelted-UNS G93106 |
| SAE AMS 2406L | Plating, Chromium Hard Deposit |
| SAE AMS 5645P | Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Tubing, and Rings 18Cr - 10Ni - 0.40Ti (SAE 30321) Solution Heat Treated-UNS S32100 |
| SAE AMS-QQ-A-250/1A | Aluminum 1100, Plate and Sheet-UNS A91100 |
| SAE AMS 4027M | (R) Aluminum Alloy, Sheet and Plate 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061; -T6 Sheet, -T651 Plate) Solution and Precipitation Heat Treated-UNS A96061 |
| SAE AMS-R-83248/1 | Rubber, Fluorocarbon Elastomer, High Temperature, Fluid, and Compression Set Resistant (O-Rings, Class 1, 75 Hardness) |
| SAE AMS 6382M | Steel, Bars, Forgings, and Rings 0.95Cr - 0.20Mo (0.38 - 0.43C) (SAE 4140) Annealed-UNS G41400 |
| SAE AMS 5557J | Steel, Corrosion and Heat-Resistant, Seamless or Welded Hydraulic Tubing 18.5Cr - 10.5Ni - 0.40Ti (SAE 30321) Solution Heat Treated-UNS S32100 |
| SAE AMS-DTL-23053/8 | Insulation Sleeving, Electrical, Heat Shrinkable, Polyvinylidene Fluoride, Semi-Rigid, Crosslinked-FSC 5970; Should Be Used Instead of MIL-DTL-23053/8C, Which Was Cancelled on 16 September 1999 |
| SAE AMS 5517L | Steel, Corrosion Resistant, Sheet and Strip 18Cr - 8Ni (SAE 30301) Cold Rolled, 125 ksi (862 MPa) Tensile Strength-UNS S30100 |
| SAE AMS-T-6736B | Tubing, Chrome-Molybdenum (4130 or 8630) Steel, Seamless and Welded |
| SAE AMS 2759/9C | (R) Hydrogen Embrittlement Relief (Baking) of Steel Parts |
| SAE AMS-DTL-23053/4 | Insulation Sleeving, Electrical, Heat Shrinkable, Polyolefin, Dual-Wall, Outer Wall Crosslinked-FSC 5970; Should Be Used Instead of MIL-DTL-23053/4D, Which Was Cancelled on 16 September 1999 |
| SAE AMS 2759/5D | Heat Treatment Martensitic Corrosion-Resistant Steel Parts |
| SAE AMS 5630J | Steel, Corrosion Resistant, Bars, Wire, and Forgings 17Cr - 0.52Mo (0.95 - 1.20C) (SAE 51440C) |
| SAE AMS 5355H | Steel, Corrosion Resistant, Investment Castings 16Cr - 4.1Ni - 0.28Cb - 3.2Cu Homogenization and Solution Heat Treated or Homogenization, Solution, and Precipitation Heat Treated-UNS J92200 |
| SAE AMS 5512L | Steel, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 18Cr - 10.5Ni - 0.80Cb (SAE 30347) Solution Heat Treated-UNS S34700 |
| SAE AMS 5518K | Steel, Corrosion Resistant, Sheet and Strip 18Cr - 8Ni (SAE 30301) Cold Rolled, 150 ksi (1034 MPa) Tensile Strength-UNS S30100 |
| SAE AMS 2488D | (R) Anodic Treatment - Titanium and Titanium Alloys Solution pH 13 or Higher |
| SAE AMS 2418G | Plating, Copper |
| SAE AMS 7259D | Rings, Sealing, Fluorocarbon (FKM) Rubber High-Temperature-Fluid Resistant Low Compression Set 85 to 95 |
| SAE AMS 2424E | Plating, Nickel Low-Stressed Deposit |
| SAE AMS 2410J | Plating, Silver Nickel Strike, High Bake |
| SAE AMS 10134A | Angle - Unequal Leg Extruded-FSC 9540 |
| SAE AMS-STD-66A | Steel: Chemical Composition and Hardenability |
| SAE AMS 2417G | Plating, Zinc-Nickel Alloy |
| SAE AMS 5862H | Steel, Corrosion-Resistant, Sheet, Strip, and Plate 15Cr - 4.5Ni - 0.30Cb (Nb) - 3.5Cu Consumable Electrode Remelted, Solution Heat Treated Precipitation-Hardenable-UNS S15500 |
| SAE AMS 2774A | Heat Treatment Wrought Nickel Alloy and Cobalt Alloy Parts |
| SAE AMS 4901P | Titanium Sheet, Strip, and Plate Commercially Pure Annealed, 70.0 ksi (485 MPa)-UNS R50700 |
| SAE AMS 10133A | Angle - Equal Leg Extruded-FSC 9540 |
| SAE AMS 4967J | Titanium Alloy, Bars, Wire, Forgings, and Rings 6.0Al - 4.0V Annealed, Heat Treatable-UNS R56400 |
| SAE AMS 2759/6B | Gas Nitriding and Heat Treatment of Low-Alloy Steel Parts |
| SAE AMS-WW-T-700A | Tube, Aluminum and Aluminum Alloy, Drawn, Seamless, General Specification for |
| SAE AMS 3276D | (R) Sealing Compound, Integral Fuel Tanks and General Purpose, Intermittent Use to 360 Degrees F (182 Degrees C) |
| SAE AMS 2470M | Anodic Treatment of Aluminum Alloys Chromic Acid Process |
| SAE AMS-M-3171 | Magnesium Alloy, Processes for Pretreatment and Prevention of Corrosion on |
| SAE AMS 3277D | Sealing Compound, Polythioether Rubber Fast Curing for Integral Fuel Tanks and General Purpose, Intermittent Use to 400 °F (204 °C) |
| SAE AMS 5383E | Nickel Alloy, Corrosion and Heat-Resistant, Investment Castings 52.5Ni - 19Cr - 3.0Mo - 5.1Cb(Nb) - 0.90Ti - 0.60Al - 18Fe Vacuum Melted Homogenization and Solution Heat Treated-UNS N07718 |
| SAE AMS 4117H | Aluminum Alloy, Rolled or Cold Finished Bars, Rods, and Wire and Flash Welded Rings 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061; -T6, -T651) Solution and Precipitation Heat Treated-UNS A96061 |
| SAE AMS 4218H | Aluminum Alloy Castings 7.0Si - 0.35Mg (A356.0-T6P) (Formerly T61P Temper) Solution and Precipitation Heat Treated-UNS A13560 |
| SAE AMS 6440P | Steel, Bars, Forgings, and Tubing 1.45Cr (0.93 - 1.05C) (SAE 52100) For Bearing Applications-UNS G52986 |
| SAE AMS 2473G | Chemical Film Treatment for Aluminum Alloys General Purpose Coating |
| SAE AMS 2759/4B | Heat Treatment Austenitic Corrosion-Resistant Steel Parts |
| SAE AMS-P-5315A | (R) Butadiene - Acrylonitrile (NBR) Rubber for Fuel-Resistant Seals 60 to 70 |
| SAE AMS-F-7190A | Forging, Steel, for Aircraft/Aerospace Equipment and Special Ordnance Applications |
| SAE AMS 5561G | Steel, Corrosion and Heat-Resistant, Welded and Drawn or Seamless and Drawn Tubing 9.0Mn - 20Cr - 6.5Ni - 0.28N High-Pressure Hydraulic-UNS S21900 |
| SAE AMS 2423D | (R) Plating, Nickel Hard Deposit |
| SAE AMS 2675G | Brazing, Nickel Alloy Filler Metal |
| SAE AMS-C-27725C | Coating, Corrosion Preventative, for Aircraft Integral Fuel Tanks for Use to 250 °F (121 °C) |
| SAE AMS 2471F | Anodic Treatment of Aluminum Alloys Sulfuric Acid Process, Undyed Coating |
| SAE AMS 4945C | Titanium Alloy Tubing, Seamless, Hydraulic 3Al - 2.5V, Controlled Contractile Strain Ratio Cold Worked, Stress Relieved-UNS R56320 |
| SAE AMS 4215G | (R) Aluminum Alloy, Castings 5.0Si - 1.2Cu - 0.50Mg (C355.0-T6) Solution and Precipitation Heat Treated-UNS A33550 |
| SAE AMS 2801B | Heat Treatment of Titanium Alloy Parts |
| SAE AMS-T-7081A | Tube, Aluminum Alloy, Seamless, Round, Drawn, 6061, Aircraft Hydraulic Quality |
| SAE AMS 5581E | Nickel Alloy, Corrosion and Heat-Resistant, Seamless or Welded Tubing 62Ni - 21.5Cr - 9.0Mo - 3.7Cb (Nb) Annealed-UNS N06625 |
| SAE AMS 6349C | Steel Bars 0.95Cr - 0.20Mo (0.38 - 0.43C) (SAE 4140) Normalized-UNS G41400 |
| SAE AMS 2759/7A | Carburizing and Heat Treatment of Carburizing Grade Steel Parts |
| SAE AMS 4219E | Aluminum Alloy Castings 7.0Si - 0.55Mg - 0.12Ti - 0.06Be (A357.0 T61P) Solution and Precipitation Heat Treated-UNS A13570 |
| SAE AMS 5504M | Steel, Corrosion and Heat-Resistant, Sheet, Strip, and Plate, 12.5Cr (SAE 51410) Annealed-UNS S41000 |
| SAE AMS 6359H | Steel, Sheet, Strip, and Plate 0.80Cr - 1.8Ni - 0.25Mo (0.38 - 0.43C) (SAE 4340)-UNS G43406 |
| SAE AMS 5647H | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Tubing, And Rings 19Cr - 9.5Ni Solution Heat Treated-UNS S30403 |
| SAE AMS-DTL-22499/1A | Shim Stock, Laminated, Aluminum Alloy-FSC 9535 |
| SAE AMS 4965J | Titanium Alloy, Bars, Wire, Forgings, and Rings 6.0AI - 4.0V Solution Heat Treated and Aged-UNS R56400 |
| SAE AMS 4777G | Nickel Alloy, Brazing Filler Metal 82Ni - 4.5Si - 7.0Cr - 3.1B - 3.0Fe 1780 to 1830 °F (971 to 999 °C) Solidus-Liquidus Range-UNS N99620 |
| SAE AMS-DTL-23053/12 | Insulation Sleeving, Electrical, Heat Shrinkable, Polytetrafluoroethylene-FSC 5970; Should Be Used Instead of MIL-DTL-23053/12C, Which Was Cancelled on 16 September 1999 |
| SAE AMS 6484C | Steel, Bars, Forgings, and Tubing 0.80Cr - 1.8Ni - 0.25Mo (0.38 - 0.43C) (SAE 4340) Normalized and Tempered |
| SAE AMS-WW-T-700/3A | Tube, Aluminum Alloy, Drawn, Seamless, 2024 |
| SAE AMS 2400W | Plating, Cadmium |
| SAE AMS 2241R | Tolerances, Corrosion and Heat-Resistant Steel, Iron Alloy, Titanium, and Titanium Alloy Bars and Wire |
| SAE AMS 2411F | Plating, Silver for High Temperature Applications |
| SAE AMS 6931A | Titanium Alloy Bars, Forgings and Forging Stock 6.0Al - 4.0V Annealed-UNS R56400 |
| SAE AMS 5754M | Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 47.5Ni - 22Cr - 1.5Co - 9.0Mo - 0.60W - 18.5Fe Solution Heat Treated-UNS N06002 |
| SAE AMS 4260F | (R) Aluminum Alloy, Investment Castings 7.0Si - 0.32Mg (356.0- T6) Solution and Precipitation Heat Treated-UNS A03560 |
| SAE AMS 2817E | Packaging and Identification Preformed Packings |
| SAE AMS 3281C | (R) Sealing Compound, Polysulfide (T) Synthetic Rubber for Integral Fuel Tank and Fuel Cell Cavities Low Density (1.20 to 1.35 sp gr), for Intermittent Use to 360 Degrees F (182 Degrees C) |
| SAE AMS-R-25988 | Rubber, Fluorosilicone Elastomer, Oil-and-Fuel-Resistant, Sheets, Strips, Molded Parts, and Extruded Shapes |
| SAE AMS 2469G | Hard Anodic Coating Treatment of Aluminum and Aluminum Alloys Processing and Performance Requirements |
| SAE AMS 2431/1D | Peening Media (ASR) Cast Steel Shot, Regular Hardness (45 to 52 HRC) |
| SAE AMS-WW-T-700/4A | Tube, Aluminum Alloy, Drawn, Seamless, 5052 |
| SAE AMS 2412H | Plating, Silver Copper Strike, Low Bake |
| SAE AMS 2694B | (R) In-Process Welding of Castings |
| SAE AMS 3218C | Fluorocarbon (FKM) Rubber High-Temperature-Fluid Resistant Low Compression Set 85 to 95 |
| SAE AMS 5519M | Steel, Corrosion Resistant, Sheet and Strip 18Cr - 8Ni (SAE 30301) Cold Rolled, 185 ksi (1276 MPa) Tensile Strength-UNS S30100 |
| SAE AMS-P-81728 | Plating, Tin-Lead (Electrodeposited) |
| SAE AMS 6257D | Steel Bars, Forgings, and Tubing 1.6Si - 0.82Cr - 1.8Ni - 0.40Mo - 0.08V (0.40 - 0.44C) Consumable Electrode Vacuum Remelted Normalized and Tempered |
| SAE AMS 5570P | Steel, Corrosion and Heat-Resistant, Seamless Tubing 18Cr - 11Ni - 0.40Ti (SAE 30321) Solution Heat Treated-UNS S32100 |
| SAE AMS 3195E | Silicone Rubber Sponge Closed Cell, Medium |
| SAE AMS 2301J | Steel Cleanliness, Aircraft Quality Magnetic Particle Inspection Procedure |
| SAE AMS-DTL-23053/1 | Insulation Sleeving, Electrical, Heat Shrinkable, Crosslinked Chlorinated Polyolefin, Flexible-FSC 5970; Should Be Used Instead of MIL-DTL-23053/1C, Which Was Cancelled on 16 September 1999 |
| SAE AMS 2485K | Coating, Black Oxide |
| SAE AMS 3652C | Polytetrafluoroethylene (PTFE) Film Non-Critical Grade |
| SAE AMS 6260P | Steel, Bars, Forgings, and Tubing 1.2Cr - 3.2Ni - 0.12Mo (0.07 - 0.13C) (SAE 9310)-UNS G93106 |
| SAE AMS 2631B | Ultrasonic Inspection Titanium and Titanium Alloy Bar and Billet |
| SAE AMS 2806B | Identification Bars, Wire, Mechanical Tubing, and Extrusions Carbon and Alloy Steels and Corrosion and Heat Resistant Steels and Alloys |
| SAE AMS 5844F | Alloy, Corrosion-Resistant, Round Bars 20Cr - 35Ni - 35Co - 10Mo Vacuum Induction Plus Consumable Electrode Vacuum Melted Solution Heat Treated and Work Strengthened-UNS R30035 |
| SAE AMS 2248F | Chemical Check Analysis Limits Corrosion and Heat Resistant Steels and Alloys, Maraging and Other Highly-Alloyed Steels, and Iron Alloys |
| SAE AMS 2371H | Quality Assurance Sampling and Testing Corrosion and Heat-Resistant Steels and Alloys Wrought Products and Forging Stock |
| SAE AMS 5734K | Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, and Tubing 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V Consumable Electrode Melted, 1650 Degrees F (899 Degrees C) Solution Heat Treated-UNS S66286 |
| SAE AMS-T-21014 | Tungsten Base Metal, High Density-Should Be Used Instead of MIL-T-21014D, Which Was Cancelled on October 5, 1998 |
| SAE AMS-P-5510 | Packing, Preformed, Straight Thread Tube Fitting Boss, Type I Hydraulic (-65 Degrees to 160 Degrees F) |
| SAE AMS-STD-401 | Sandwich Constructions and Core Materials; General Test Methods-FSC 5680; Should Be Used Instead of MIL-STD-401B, Which Was Cancelled on 24 September 1999 |
| SAE AMS 1424H | (R) Deicing/Anti-Icing Fluid, Aircraft SAE Type I |
| SAE AMS 10136A | Tee - Extruded-FSC 9540 |
| SAE AMS 5362K | Steel, Corrosion and Heat Resistant, Investment Castings 19Cr - 12Ni - 1.0(Cb + Ta) Solution Heat Treated-UNS J92811 |
| SAE AMS 6348C | Steel, Bars 0.95Cr - 0.20Mo (0.28 to 0.33C) (SAE 4130) Normalized-UNS G41300 |
| SAE AMS 2300K | Steel Cleanliness, Premium Aircraft-Quality Magnetic Particle Inspection Procedure |
| SAE AMS 3265B | (R) Sealing Compound, Polysulfide (T) Rubber, Fuel Resistant, Nonchromated Corrosion Inhibiting For Intermittent Use to 360 °F (182 °C) |
| SAE AMS 6370M | Steel, Bars, Forgings, and Rings 0.95Cr - 0.20Mo (0.28 - 0.33C) (SAE 4130)-UNS G41300 |
| SAE AMS 4340E | Aluminum Alloy, Extrusions 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (7050-T76511) Solution Heat Treated, Stress Relieved, Straightened, and Overaged-UNS A97050 |
| SAE AMS 2380E | Approval and Control of Premium-Quality Titanium Alloys |
| SAE AMS 6411F | Steel Bars, Forgings, and Tubing 0.88Cr - 1.8Ni - 0.42Mo - 0.08V (0.28 - 0.33C) Consumable Electrode Remelted-UNS K23080 |
| SAE AMS 6409C | Steel, Bars, Forgings, and Tubing 0.80Cr - 1.8Ni - 0.25Mo (0.38 - 0.43C) (SAE 4340) Special Aircraft Quality Cleanliness Normalized and Tempered-UNS G43406 |
| SAE AMS 6487J | Steel, Bars, and Forgings 5.0Cr - 1.3Mo - 0.50V (0.38 - 0.43C) (H-11) Consumable Electrode Vacuum Melted-UNS T20811 |
| SAE AMS-DTL-23053/13 | Insulation Sleeving, Electrical, Heat Shrinkable, Fluoroelastomer, Flexible-FSC 5970; Should Be Used Instead of MIL-DTL-23053/13B, Which Was Cancelled on 16 September 1999 |
| SAE AMS 2518B | Thread Compound, Anti-Seize, Graphite-Petrolatum |
| SAE AMS 2681B | Welding, Electron-Beam |
| SAE AMS 4347C | Aluminum Alloy Sheet 1.0Mg - 0.8Si - 0.8Cu - 0.5Mn (6013-T4) Solution Heat Treated and Naturally Aged-UNS A96013 |
| SAE AMS-QQ-A-200/9A | Aluminum Alloy 6063, Bar, Rod, Shapes, Tube, and Wire, Extruded-UNS A96063 |
| SAE AMS 5837G | Nickel Alloy, Corrosion and Heat Resistant, Welding Wire 62Ni - 21.5Cr - 9.0Mo - 3.7Cb(Nb)-UNS N06625 |
| SAE AMS 2615F | Pressure Testing, Hydraulic Pressure as Specified |
| SAE AMS 5901B | Steel, Corrosion Resistant, Sheet, Strip, and Plate 18Cr - 8Ni (SAE 30301) Solution Heat Treated-UNS S30100 |
| SAE AMS 4289 | Aluminum Alloy Castings 7.0Si - 0.55Mg - 0.12Ti (F357.0-T6) and Precipitation Heat Treated |
| SAE AMS-DTL-23053/11 | Insulation Sleeving, Electrical, Heat Shrinkable, Fluorinated Ethylene Propylene, Non-Crosslinked-FSC 5970; Should Be Used Instead of MIL-DTL-23053/11C, Which Was Cancelled on 16 September 1999 |
| SAE AMS 2355H | Quality Assurance, Sampling and Testing Aluminum Alloys and Magnesium Alloy Wrought Products, Except Forging Stock, and Rolled, Forged, or Flash Welded Rings |
| SAE AMS 5708J | Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 58Ni - 19.5Cr - 13.5Co - 4.3Mo - 3.0Ti - 1.4AI Consumable Electrode or Vacuum Induction Melted 1975 degrees F (1079 degrees C) Solution Heat Treated-UNS N07001 |
| SAE AMS 5610N | Steel, Corrosion and Heat-Resistant, Bars, Wire, and Forgings 12.5Cr - Low Carbon (SAE 51416, 51416Se) Free-Machining-UNS S41600 and S41623 |
| SAE AMS 5616L | Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Tubing, and Rings 13Cr - 2.0Ni - 3.0W Annealed-UNS S41800 |
| SAE AMS-R-6855A | Elastomer, Synthetic, Sheets, Strips, Molded or Extruded Shapes, General Specification for-Should Be Used Instead of MIL-R-6855, Which Was Cancelled on December 18, 1998 |
| SAE AMS 5664E | Nickel Alloy, Corrosion and Heat Resistant, Bars, Forgings, and Rings 52.5Ni - 19Cr - 3.0Mo - 5.1Cb - 0.90Ti - 0.50A1 - 18Fe Consumable Electrode or Vacuum Induction Melted 1950 Degrees F (1066 Degrees C) Solution Heat Treated, Precipitation Hardenable-UNS N07718 |
| SAE AMS 10137A | Channel - Extruded-FSC 9540 |
| SAE AMS 5853C | Steel, Corrosion and Heat Resistant, Bars and Wire 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V Consumable Electrode Melted 1800 Degrees F (982 Degrees C) Solution Treated and Work-Strengthened 160 ksi (1103 MPa) Tensile Strength-UNS S66286 |
| SAE AMS 4943G | Titanium Alloy, Hydraulic, Seamless Tubing 3.0Al - 2.5V Annealed-(UNS R56320) |
| SAE AMS 5511H | Steel, Corrosion-Resistant, Sheet, Strip, and Plate 19Cr - 9.5Ni (304L) Solution Heat Treated-UNS S30403 |
| SAE AMS 6470L | Steel, Nitriding, Bars, Forgings, and Tubing 1.6Cr - 0.35Mo - 1.13Al (0.38 - 0.43C)-UNS K24065 |
| SAE AMS 5343E | Steel, Corrosion-Resistant, Investmment Castings 16Cr - 4.1Ni - 0.28Cb - 3.2Cu Homogenization, Solution, and Precipitation Heat Treated (H1000) 150 ksi (1034 MPa) Tensile Strength-UNS J92200; UNS J92180 |
| SAE AMS 2422E | (R) Plating, Gold |
| SAE AMS 5046C | Carbon Steel, Sheet, Strip, and Plate (SAE 1020 and 1025) Annealed-UNS G10200 and UNS G10250 |
| SAE AMS-P-5516 | Packing, Preformed, Petroleum Hydraulic Fluid Resistant, 160 Degrees F |
| SAE AMS 3304G | Silicone, Rubber General Purpose 70 Durometer |
| SAE AMS 6444K | Steel, Bars, Forgings, and Tubing 1.45Cr (0.93 - 1.05C) (SAE 52100) Premium Aircraft-Quality, Consumable Electrode Vacuum Remelted-UNS G52986 |
| SAE AMS 6491C | Steel Bars, Forgings, and Tubing 4.1Cr - 4.2Mo - 1.0V (0.80 - 0.85C) Premium Aircraft-Quality for Bearing Applications, Double Vacuum Melted-UNS T11350 |
| SAE AMS-QQ-A-250/30 | Aluminum Alloy 2219, Plate and Sheet-UNS A92219 |
| SAE AMS 4902H | Titanium Sheet, Strip, and Plate Commercially-Pure Annealed 40.0 ksi (276 MPa) Yield Strength-UNS R50400 |
| SAE AMS 2807A | Identification Carbon and Low-Alloy Steels, Corrosion and Heat Resistant Steels and Alloys Sheet, Strip, Plate, and Aircraft Tubing |
| SAE AMS 2482C | Hard Coating Treatment of Aluminum Alloys Teflon-Impregnated or Codeposited |
| SAE AMS 6304K | Low-Alloy Steel, Heat-Resistant, Bars, Forgings, and Tubing 0.95Cr - 0.55Mo - 0.30V (0.40 - 0.50C)-UNS K14675 |
| SAE AMS 4975J | Titanium Alloy, Bars, Wire, and Rings 6.0Al - 2.0Sn - 4.0Zr - 2.0Mo - 0.08Si Solution and Precipitation Heat Treated-UNS R54620 |
| SAE AMS 3302G | Silicone Rubber General Purpose 50 Durometer |
| SAE AMS-P-83461/2 | Packing, Preformed, Petroleum Hydraulic Fluid Resistant, Improved Performance at 275 Degree F (135 Degree C) For use in Boss Fittings, Sizes and Tolerances-FSC 5330 |
| SAE AMS 5121J | Sheet and Strip, Steel (0.90 - 1.04C) (SAE 1095) Annealed-UNS G10950 |
| SAE AMS 6300E | Steel Bars and Forgings 0.25Mo (0.35 - 0.40C) (SAE 4037)-UNS G40370 |
| SAE AMS 4108F | Aluminum Alloy, Hand Forgings 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (7050-T7452) Solution Heat Treated, Compression Stress-Relieved, and Overaged-UNS A97050 |
| SAE AMS-G-4343 | Grease, Pneumatic System-FSC 9150; Should Be Used Instead of MIL-G-4343C, Which Was Cancelled on 10 September 1999 |
| SAE AMS 2649C | Etch Inspection of High Strength Steel Parts |
| SAE AMS 5524K | Steel, Corrosion and Heat-Resistant, Sheet, Strip and Plate 18Cr - 13Ni - 2.5Mo (SAE 30316) Solution Heat Treated-UNS S31600 |
| SAE AMS 3374C | (R) Sealing Compound Aircraft Firewall-FSC 8030 |
| SAE AMS 5618G | Steel, Corrosion Resistant, Bars, Wire, and Forgings 17Cr - 0.52Mo (0.95 - 1.20C) (SAE 51440C) Consumable Electrode Vacuum Melted-UNS S44004 |
| SAE AMS 5344F | (R) Steel, Corrosion-Resistant, Investment Castings 16Cr - 4.1Ni - 0.28Cb - 3.2Cu Homogenization, Solution, and Precipitation Heat Treated (H900) 180 ksi (1241 MPa) Tensile Strength (17-4)-UNS J92180 and J92200 |
| SAE AMS 2416K | Plating, Nickel-Cadmium Diffused |
| SAE AMS 6351G | Steel Sheet, Strip, and Plate 0.95Cr - 0.20Mo (0.28 - 0.33C) (SAE 4130) Spheroidized-UNS G41300 |
| SAE AMS 4880D | Aluminum Bronze Alloy, Centrifugal and Continuous-Cast Castings 81.5Cu - 10.3Al - 5.0Ni - 2.8Fe Quench Hardened and Temper Annealed (TQ50)-UNS C95510 |
| SAE AMS 2243H | Tolerances Corrosion and Heat-Resistant Steel Tubing |
| SAE AMS 3656E | Polytetrafluoroethylene Extrusions Normal Strength, as Sintered |
| SAE AMS-DTL-22499/3 | Shim Stock, Laminated, CRES-FSC 9515 |
| SAE AMS 2432C | Shot Peening, Computer Monitored |
| SAE AMS 4037N | Aluminum Alloy, Sheet and Plate 4.4Cu - 1.5Mg - 0.60Mn (2024; -T3 Flat Sheet, -T351 Plate) Solution Heat Treated |
| SAE AMS-QQ-A-200/16A | Aluminum Alloy, Structural Shapes, Extruded, 6061-UNS A96061 |
| SAE AMS-C-6183 | Cork and Rubber Composition Sheet; for Aromatic Fuel and Oil Resistant Gaskets |
| SAE AMS 5617J | Steel Bars, Wire, and Forgings, Corrosion Resistant 12Cr - 8.5Ni - 1.2Ti - 2.0Cu Vacuum Induction Plus Vacuum Consumable Electrode Melted Solution Heat Treated, Precipitation Hardenable-UNS S45500 |
| SAE AMS 4311E | Aluminum Alloy, Rolled or Forged Rings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T7351, 7075-T7352) Solution Heat Treated, Mechanically Stress Relieved, and Precipitation Heat Treated-UNS A97075 |
| SAE AMS 4946B | Titanium Alloy Tubing, Seamless, Hydraulic 3Al - 2.5V, Texture Controlled Cold Worked, Stress Relieved-UNS R56320 |
| SAE AMS-DTL-23053/18 | Insulation Sleeving, Electrical, Heat Shrinkable, Modified Fluoropolymer, Crosslinked-FSC 5970; Should Be Used Instead MIL-DTL-23053/18B, Which Was Cancelled on 25 February 2000 |
| SAE AMS 2262G | Nickel, Nickel Alloy, and Cobalt Alloy Sheet, Strip, and Plate |
| SAE AMS 2474D | Chemical Treatment for Aluminum Alloys Low Electrical Resistance Coating |
| SAE AMS 2808D | Identification Forgings |
| SAE AMS-R-83248/2 | Rubber, Fluorocarbon Elastomer, High Temperature, Fluid and Compression Set Resistant (O-Rings, Class 2, 90 Hardness) |
| SAE AMS 5759K | Cobalt Alloy, Corrosion and Heat Resistant, Bars, Forgings, and Rings 52Co - 20Cr - 10Ni - 15W Solution Heat Treated-UNS R30605 |
| SAE AMS 4787F | Gold-Nickel Alloy, Brazing Filler Metal, High Temperature 82Au - 18Ni 1740 °F (949 °C) Solidus-Liquidus Temperature-P00820 |
| SAE AMS-QQ-A-200/15A | Aluminum Alloy Bar, Rod, Shapes, Extruded, 7075-T76 Improved Exfoliation Resistance-UNS A97075 |
| SAE AMS 4144F | Aluminum Alloy, Hand Forgings and Rolled Rings 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti (2219-T852/T851) Solution Heat Treated, Mechanically Stress Relieved, and Precipitation Heat Treated (UNS A92219) |
| SAE AMS 6419F | Steel, Bars, Forgings, and Tubing 1.6Si - 0.82Cr - 1.8Ni - 0.40Mo - 0.08V (0.40 - 0.45C) Consumable Electrode Vacuum Remelted-UNS K44220 |
| SAE AMS 4976G | Titanium Alloy, Forgings 6.0Al - 2.0Sn - 4.0Zr - 2.0Mo Solution and Precipitation Heat Treated-UNS R54620 |
| SAE AMS 4120R | Aluminum Alloy, Rolled or Cold Finished Bars, Rods, and Wire 4.4Cu - 1.5Mg - 0.60Mn (2024) Solution Heat Treated and Naturally Aged (T4) Solution Heat Treated, Cold Worked, and Naturally Aged (T351)-UNS A92024 |
| SAE AMS 4921L | Titanium Bars, Wire, Forgings, and Rings Commercially Pure 70 ksi (483 MPa) Yield Strength-UNS R50700 |
| SAE AMS 4935H | Titanium Alloy Extrusions and Flash Welded Rings 6Al - 4V Annealed Beta Processed-UNS R56400 |
| SAE AMS 5665M | Nickel Alloy, Corrosion and Heat Resistant, Bars, Forgings, and Rings 74Ni - 15.5Cr - 8.0Fe-UNS N06600 |
| SAE AMS 5707K | Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 58Ni - 19.5Cr - 13.5Co - 4.3Mo - 3.0Ti - 1.4Al - 0.05Zr - 0.006B Consumable Electrode Remelted or Vacuum Induction Melted 1825 to 1900 degrees F (996 to 1038 Degrees C) Solution, Stabilization, and Precipitation Heat Treated-UNS N07001 |
| SAE AMS 3824C | Cloth, Glass Finished for Resin Laminates |
| SAE AMS 2759/8A | (R) Ion Nitriding |
| SAE AMS 3660C | Polytetrafluoroethylene (PTFE) Moldings General Purpose Grade, as Sintered |
| SAE AMS-M-7866A | Molybdenum Disulfide, Technical, Lubrication Grade |
| SAE AMS-STD-753A | Corrosion-Resistant Steel Parts: Sampling, Inspection and Testing for Surface Passivation |
| SAE AMS 4078G | Aluminum Alloy Plate (7075-T7351) Solution Heat Treated, Stress Relieved, and Overaged-UNS A97075 |
| SAE AMS 4439F | Magnesium Alloy Castings 4.2Zn - 1.2Rare Earths - 0.7Zr (ZE41A-T5) Precipitation Heat Treated-UNS M16410 |
| SAE AMS 2680C | Electron-Beam Welding for Fatigue Critical Applications |
| SAE AMS 5589E | Nickel Alloy, Corrosion and Heat-Resistant, Seamless Tubing 52.5Ni - 19Cr - 3.0Mo - 5.1Cb (Nb) - 0.90Ti - 0.50Al - 18Fe Consumable Electrode Remelted or Vacuum Induction Melted 1775 °F (968 °C) Solution Heat Treated-Composition similar to UNS N07718 |
| SAE AMS 2431/6C | Peening Media Glass Shot |
| SAE AMS-QQ-A-225/1B | Aluminum Alloy, Bar, Rod, and Wire, Rolled, Drawn, or Cold Finished, 1100-UNS A91100 |
| SAE AMS 2759/11 | Stress Relief of Steel Parts |
| SAE AMS 5832F | Nickel Alloy, Corrosion and Heat Resistant, Welding Wire 52.5Ni - 19Cr - 3.0Mo - 5.1Cb - 0.90Ti - 0.50Al - 18Fe Consumable Electrode or Vacuum Induction Melted-UNS N07718 |
| SAE AMS 4083K | Aluminum Alloy Tubing, Hydraulic, Seamless, Drawn, Round 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T6) Solution and Precipitation Heat Treated-Ref. UNS 96061 |
| SAE AMS 4900M | Titanium Sheet, Strip, and Plate Commercially Pure Annealed, 55.0 ksi (379 MPa) Yield Strength-UNS R50550 |
| SAE AMS 5726D | Steel, Corrosion and Heat-Resistant, Bars and Wire 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V 1800 °F (982 °C) Solution Heat Treated and Work-Strengthened Consumable Electrode Melted 200 ksi (1379 MPa) Tensile Strength-UNS S66286 |
| SAE AMS-QQ-A-250/24A | Aluminum Alloy, 7075, Plate and Sheet (Improved Exfoliation Resistant) |
| SAE AMS 6274N | Steel Bars, Forgings, and Tubing 0.50Cr - 0.55Ni - 0.20Mo (0.18 - 0.23C)(SAE 8620)-UNS G86200 |
| SAE AMS 3209L | Chloroprene (CR) Rubber Weather Resistant 65 - 75 |
| SAE AMS 2431/2D | Peening Media (ASH) Cast Steel Shot, High Hardness (55 to 62 HRC) |
| SAE AMS 3667C | Polytetrafluoroethylene Sheet, Molded General Purpose Grade, as Sintered |
| SAE AMS 2431B | Peening Media General Requirements |
| SAE AMS 4127J | Aluminum Alloy, Forgings and Rolled or Forged Rings (6061-T6) Solution and Precipitation Heat Treated-UNS A96061 |