|
SAE AMS-C-8837 |
Coating, Cadmium (Vacuum Deposited)-AREA MFFP; Should Be Used Instead of MIL-C-8837B, Which Was Cancelled on 10 September 1999 |
|
SAE AMS 5680J |
Steel, Corrosion and Heat-Resistant, Welding Wire 18.5Cr - 11Ni - 0.40Cb (Nb) (SAE 30347)-UNS S34781 |
|
SAE AMS 4919F |
Titanium Alloy Sheet, Strip, and Plate 6Al - 2Sn - 4Zr - 2Mo - 0.08Si Duplex Annealed-UNS R54620 |
|
SAE AMS 5848C |
Steel, Corrosion Resistant, Bars, Wire, Forgings, Extrusions, Tubing, and Rings Wear and Galling Resistant 8.0Mn - 4.0Si - 17Cr - 8.5Ni - 0.13N Solution Heat Treated-UNS S21800 |
|
SAE AMS 2259E |
Chemical Check Analysis Limits Wrought Low-Alloy and Carbon Steels |
|
SAE AMS 2809A |
Identification Titanium and Titanium Alloy Wrought Products |
|
SAE AMS 4150L |
Aluminum Alloy, Extrusions and Rings 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr - (6061-T6) Solution and Precipitation Heat Treated-UNS A96061 |
|
SAE AMS 7490P |
Rings, Flash Welded Corrosion and Heat Resistant Austenitic Steels, Austenitic-Type Iron, Nickel, or Cobalt Alloys, or Precipitation-Hardenable Alloys |
|
SAE AMS 2405C |
Electroless Nickel Plating Low Phosphorus-Reaffirmed Non-Current April 2006 |
|
SAE AMS 4201E |
Aluminum Alloy Plate 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (7050-T7651) Solution Heat Treated, Stress Relieved, and Overaged-UNS A97050 |
|
SAE AMS 5648K |
Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Tubing, and Rings 17Cr - 12Ni - 2.5Mo Solution Heat Treated-UNS S31600 |
|
SAE AMS-C-83231A |
Coatings, Polyurethane, Rain Erosion Resistant for Exterior Aircraft and Missile Plastic Parts-FSC 8010 |
|
SAE AMS-I-23011B |
Iron-Nickel Alloys for Sealing to Glasses and Ceramic |
|
SAE AMS 5612J |
Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Tubing, and Rings 12Cr Ferrite Controlled, Annealed-UNS S41001 |
|
SAE AMS-DTL-22499/4 |
Shim Stock, Laminated, Carbon Steel |
|
SAE AMS 5962A |
Nickel Alloy, Corrosion and Heat-Resistant, Round Bars and Wire 52.5Ni - 19Cr - 3.0Mo - 5.1Cb - 0.90Ti - 0.50Al - 18Fe Consumable Electrode or Vacuum Induction Melted 1775 Degrees F (968 Degrees C) Solution Treated and Work Strengthened Precipitation Hardenable-UNS N07718 |
|
SAE AMS-H-7199 |
Heat Treatment of Wrought Copper-Beryllium Alloys, Process for (Copper Alloys: Numbers C17000, C17200, C17300, C17500, and C17510) |
|
SAE AMS 2665G |
Brazing, Silver For Use Up to 400 °F (204 °C) |
|
SAE AMS 5506F |
Steel, Corrosion and Heat Resistant, Sheet, Strip, and Plate 13Cr (0.30 - 0.40C) (SAE 51420) Annealed-UNS S42000 |
|
SAE AMS 4045J |
Aluminum Alloy Sheet and Plate 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr 7075: (-T6 Sheet, -T651 Plate) Solution and Precipitation Heat Treated-UNS A97075 |
|
SAE AMS 4288 |
Aluminum Alloy Castings 7.0Si - 0.58Mg - 0.15Ti (E357.0-T6) Solution and Precipitation Heat Treated |
|
SAE AMS 6360L |
Steel Tubing, Seamless 0.95Cr - 0.20Mo (0.28 - 0.33C) (SAE 4130) Normalized or Stress Relieved-UNS G41300 |
|
SAE AMS 4590B |
Extrusions Nickel-Aluminum Bronze, Martensitic 78.5Cu - 10.5Al - 5.1Ni - 4.8Fe Solution Heat Treated and Tempered (TQ50)-UNS C63020 |
|
SAE AMS 4149D |
Aluminum Alloy, Die and Hand Forgings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7175-T74) Solution and Precipitation Heat Treated-UNS A97175 |
|
SAE AMS 5936C |
Steel, Corrosion-Resistant, Bars, Wire, and Forgings 12Cr - 11Ni - 1.7Ti - 1Mo Vacuum Induction Plus Vacuum Consumable Electrode Melted Solution Heat Treated, Precipitation Hardenable-UNS S46500 |
|
SAE AMS 6400 |
Forgings, Steel For Aircraft/Aerospace Equipment |
|
SAE AMS 2769A |
Heat Treatment of Parts in a Vacuum |
|
SAE AMS 2472F |
Anodic Treatment of Aluminum Alloys Sulfuric Acid Process, Dyed Coating |
|
SAE AMS 5537H |
Cobalt Alloy, Corrosion and Heat-Resistant, Sheet, Strip, Foil, and Plate 52Co - 20Cr - 10Ni - 15W Solution Heat Treated-UNS R30605 |
|
SAE AMS 5556H |
Steel, Corrosion and Heat Resistant, Seamless or Welded Hydraulic Tubing 18Cr - 11Ni - 0.70Cb (SAE 30347) Solution Heat Treated-UNS S34700 |
|
SAE AMS 4533B |
Copper-Beryllium Alloy, Bars and Rods 98Cu - 1.9Be Solution and Precipitation Heat Treated (TF00, formerly AT)-UNS C17200 |
|
SAE AMS-A-25463 |
Adhesive, Film Form, Metallic Structural Sandwich Construction-FSC 8040 |
|
SAE AMS 2269F |
Chemical Check Analysis Limits Nickel, Nickel Alloys, and Cobalt Alloys |
|
SAE AMS 4082N |
Aluminum Alloy, Seamless Drawn Tubing 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T6) Solution and Precipitation Heat Treated-UNS A96061 |
|
SAE AMS 5653F |
Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Tubing, and Rings 17Cr - 12Ni - 2.5Mo (0.030 Max C) Solution Heat Treated-UNS S31603 |
|
SAE AMS 5540M |
Nickel Alloy, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 74Ni - 15.5Cr - 8.0Fe Annealed-UNS N06600 |
|
SAE AMS 10138A |
Zee - Equal Leg Extruded-FSC 9540 |
|
SAE AMS 2647B |
(R) Fluorescent Penetrant Inspection Aircraft and Engine Component Maintenance |
|
SAE AMS 5567E |
Steel, Corrosion Resistant, Seamless or Welded Hydraulic Tubing 19Cr - 10Ni (SAE 30304) Solution Heat Treated-UNS S30400 |
|
SAE AMS 5342E |
Steel, Corrosion-Resistant, Investment Castings 16Cr - 4.1Ni - 0.28Cb (Nb) - 3.2Cu Homogenization, Solution, and Precipitation Heat Treated (H1100) 130 ksi (896 MPa) Tensile Strength (17-4)-UNS J91280 and UNS J92200 |
|
SAE AMS-QQ-A-250/2A |
Aluminum Alloy 3003, Plate and Sheet-UNS A93003 |
|
SAE AMS 2447C |
Coating, Thermal Spray High Velocity Oxygen/Fuel Process |
|
SAE AMS 5709G |
Nickel Alloy, Corrosion and Heat Resistant, Bars and Forgings 58Ni - 19.5Cr - 13.5Co - 4.3Mo - 3.0Ti - 1.4Al - 0.05Zr - 0.006B Consumable Electrode or Vacuum Induction Melted 1975 Degrees F (1079 Degrees C) Solution, Stabilization, and Precipitation Heat Treated-UNS N07001 |
|
SAE AMS 2486D |
Conversion Coating of Titanium Alloys Fluoride-Phosphate Type |
|
SAE AMS 4190H |
Aluminum Alloy, Welding Wire 5.2Si (4043)-UNS A94043 |
|
SAE AMS 5542N |
Nickel Alloy, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 72Ni - 15.5Cr - 0.95Cb(Nb) - 2.5Ti - 0.70Al - 7.0Fe Annealed-UNS N07750 |
|
SAE AMS 2451B |
Plating, Brush General Requirements |
|
SAE AMS 5040M |
Steel, Sheet and Strip 0.15 Carbon, Maximum Deep Forming Grade-UNS G10100 |
|
SAE AMS 4124D |
Aluminum Alloy, Rolled or Cold Finished Bars, Rods, and Wire 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T7351) Solution Heat Treated, Stress Relieved by Stretching, and Overaged-UNS A97075 |
|
SAE AMS-I-23053/2 |
Insulation Sleeving, Electrical, Heat Shrinkable, Polyvinyl Chloride, Flexible Crosslinked and Non-Crosslinked-FSC 5970; Should Be Used Instead of MIL-I-23053/2C, Which Was Cancelled on 16 September 1999 |
|
SAE AMS 4778H |
Nickel Alloy, Brazing Filler Metal 92Ni - 4.5Si - 3.1B 1800 to 1900 °F Solidus-Liquidus Range-UNS N99630 |
|
SAE AMS 5608E |
Cobalt Alloy, Corrosion and Heat Resistant, Sheet, Strip, and Plate 40Co - 22Cr - 22Ni - 14.5W - 0.07La Solution Heat Treated-UNS R30188 |
|
SAE AMS 4013F |
Aluminum Sheet, Laminated Surface Bonded |
|
SAE AMS 4141E |
Aluminum Alloy Die Forgings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T73) Solution and Precipitation Heat Treated |
|
SAE AMS 6417F |
Steel, Bars, Forgings, and Tubing 1.6Si - 0.82Cr - 1.8Ni - 0.40Mo - 0.08V (0.38 - 0.43C) Consumable Electrode Vacuum Remelted |
|
SAE AMS 5845G |
Alloy, Corrosion-Resistant, Round Bars 20Cr - 35Ni - 35Co - 10Mo Vacuum Induction Plus Consumable Electrode Vacuum Melted Solution Heat Treated, Work Strengthened, and Aged-UNS R30035 |
|
SAE AMS 5566L |
Steel, Corrosion Resistant, Seamless or Welded Hydraulic Tubing 19Cr - 10Ni (SAE 30304) High Pressure, Cold Drawn-UNS S30400 |
|
SAE AMS 6512E |
Steel, Bars, Forgings, Tubing, and Rings 18Ni - 7.8Co - 4.9Mo - 0.40Ti - 0.10A1 Consumable Electrode Vacuum Melted, Annealed-UNS K92890 |
|
SAE AMS 5798F |
Nickel Alloy, Corrosion and Heat Resistant, Welding Wire 47.5Ni - 22Cr - 1.5Co - 9.0Mo - 0.60W - 18.5Fe-(Composition similar to UNS N06002) |
|
SAE AMS 3303J |
Silicone, Rubber General Purpose 60 Durometer |
|
SAE AMS 5382J |
Cobalt Alloy, Corrosion and Heat Resistant, Investment Castings 54Co - 25.5Cr - 10.5Ni - 7.5W as Cast-UNS R30031 |
|
SAE AMS-DTL-23053/6 |
Insulation Sleeving, Electrical, Heat Shrinkable, Polyolefin, Semi-Rigid, Crosslinked-FSC 5970; Should Be Used Instead of MIL-DTL-23053/6D, Which Was Cancelled on 16 September 1999 |
|
SAE AMS-QQ-A-250/3 |
Aluminum Alloy Alclad 2014, Plate and Sheet |
|
SAE AMS 5786F |
Nickel Alloy, Corrosion and Heat-Resistant, Welding Wire 62.5Ni - 5.0Cr - 24.5Mo - 5.5Fe-UNS N10004 |
|
SAE AMS 5866D |
Steel, Corrosion Resistant, Flat Wire 18Cr - 9.0Ni (SAE 30302) Spring Temper-UNS S30200 |
|
SAE AMS 6930A |
Titanium Alloy Bars, Forgings and Forging Stock 6.0Al - 4.0V Solution Heat Treated and Aged-UNS R56400 |
|
SAE AMS 4107F |
Aluminum Alloy Die Forgings (7050-T74) Solution Heat Treated and Overaged-UNS A97050 |
|
SAE AMS 4025K |
Aluminum Alloy, Sheet and Plate 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-0) Annealed-UNS A96061 |
|
SAE AMS 4957D |
Titanium Alloy, Round Bar and Wire 3AI - 8V - 6Cr - 4Mo - 4Zr Consumable Electrode Melted Solution Heat Treated and Cold Drawn-UNS R58640 |
|
SAE AMS 5910B |
Steel, Corrosion Resistant, Sheet, Strip, and Plate 19Cr - 9.2Ni (SAE 30304) Cold Rolled, 125 ksi (862 MPa) Tensile Strength-UNS S30400 |
|
SAE AMS 6490F |
Steel Bars, Forgings, and Tubing 4.0Cr - 4.2Mo - 1.0V (0.77 - 0.85C) Premium Aircraft-Quality for Bearing Applications Consumable Electrode Vacuum Melted-Composition similar to UNS T11350 |
|
SAE AMS 2433C |
Plating, Nickel-Thallium-Boron or Nickel-Boron Electroless Deposition |
|
SAE AMS 5706K |
(R) Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 57Ni - 19.5Cr - 13.5Co - 4.3Mo - 3.0Ti - 1.4AI - 0.006B - 0.05Zr Consumable Electrode or Vacuum Induction Melted 1825 to 1900 °F Solution Heat Treated-UNS N07001 |
|
SAE AMS 2481G |
Phosphate Treatment Antichafing |
|
SAE AMS 5544J |
Nickel Alloy, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 57Ni - 19.5Cr - 13.5Co - 4.2Mo - 3.0Ti - 1.4Al - 0.05Zr - 0.006B Consumable Electrode or Vacuum Induction Melted, Annealed-UNS N07001 |
|
SAE AMS 2375D |
Control of Forgings Requiring First Article Approval |
|
SAE AMS 2401H |
Plating, Cadmium Low Hydrogen Content Deposit |
|
SAE AMS 2641A |
Vehicle, Magnetic Particle Inspection Petroleum Base |
|
SAE AMS 2630B |
Inspection, Ultrasonic Product over 0.5 Inch (12.7 mm) Thick-Best Copy Available |
|
SAE AMS 3819C |
Cloths, Cleaning For Aircraft Primary and Secondary Structural Surfaces |
|
SAE AMS 2249F |
Chemical Check Analysis Limits Titanium and Titanium Alloys |
|
SAE AMS 5085F |
Steel Sheet, Strip, and Plate 0.47 - 0.55C (SAE 1050) Annealed-UNS G10500 |
|
SAE AMS 5689F |
Steel, Corrosion and Heat Resistant, Wire 18Cr - 10.5Ni - 0.40Ti (SAE 30321) Solution Heat Treated-UNS S32100 |
|
SAE AMS 5699G |
Nickel Alloy, Corrosion and Heat-Resistant, Wire 72Ni - 15.5Cr - 0.95Cb - 2.5Ti - 0.70Al - 7.0Fe Spring Temper, Precipitation Hardenable-UNS N07750 |
|
SAE AMS 5825G |
Steel, Corrosion-Resistant, Welding Wire 16.4Cr - 4.8Ni - 0.22Cb(Nb) - 3.6Cu-UNS S17480 |
|
SAE AMS-QQ-S-700B |
Steel, Sheet and Strip, Medium and High Carbon |
|
SAE AMS 4026L |
Aluminum Alloy, Sheet and Plate 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061; -T4 Sheet, -T451 Plate) Solution Heat Treated and Naturally Aged-UNS A96061 |
|
SAE AMS 6528B |
Steel, Bars 0.95Cr - 0.20Mo (0.28 - 0.33C) (SAE 4130) Special Aircraft Quality Cleanliness Normalized-UNS G41300 |
|
SAE AMS 1428F |
Fluid, Aircraft Deicing/Anti-icing, Non-Newtonian (Pseudoplastic), SAE Types II, III, and IV |
|
SAE AMS 6427J |
Steel Bars, Forgings, and Tubing 0.88Cr - 1.8Ni - 0.42Mo - 0.08V (0.25 - 0.33C)-UNS K23080 |
|
SAE AMS-WW-T-700/7 |
Tube, Aluminum Alloy, Drawn, Seamless, 7075 |
|
SAE AMS 2370J |
Quality Assurance Sampling and Testing Carbon and Low-Alloy Steel Wrought Products and Forging Stock |
|
SAE AMS 2437C |
Coating, Plasma Spray Deposition |
|
SAE AMS 2670J |
Brazing, Copper |
|
SAE AMS 4133D |
Aluminum Alloy Forgings and Rolled Rings 4.4Cu - 0.85Si - 0.80Mn - 0.50Mg (2014-T6) Solution and Precipitation Heat Treated-UNS A92014 |
|
SAE AMS 4944G |
Titanium Alloy Tubing, Seamless, Hydraulic 3.0Al - 2.5V Cold Worked, Stress Relieved-UNS R56320 |
|
SAE AMS 6371J |
Steel, Mechanical Tubing 0.95Cr - 0.20Mo (0.28 - 0.33C) (SAE 4130)-UNS G413000 |
|
SAE AMS 7271H |
Rings, Sealing, Butadiene-Acrylonitrile (NBR) Rubber Fuel and Low Temperature Resistant 60 - 70 |
|
SAE AMS 2673D |
Brazing, Aluminum and Aluminum Alloys Molten Flux (Dip) |
|
SAE AMS-DTL-23053/16 |
Insulation Sleeving, Electrical, Heat Shrinkable, Crosslinked, Elastromeric Polyolefin, Flexible-FSC 5970; Should Be Used Instead of MIL-DTL-23053/16B, Which Was Cancelled on 16 September 1999 |
|
SAE AMS 6472D |
Steel, Bars and Forgings, Nitriding 1.6Cr - 0.35Mo - 1.1Al (0.38 - 0.43C) Hardened and Tempered, 112 ksi (772 MPa) Tensile Strength-UNS K24065 |
|
SAE AMS-QQ-A-200/1A |
Aluminum Alloy 3003, Bar, Rod, Shapes, Tube, and Wire, Extruded-UNS A93003 |
|
SAE AMS 4081H |
Aluminum Alloy Tubing, Hydraulic, Seamless, Drawn, Round 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T4) Solution Heat Treated and Naturally Aged-UNS A96061 |
|
SAE AMS 5576K |
Steel, Corrosion and Heat-Resistant, Welded Tubing 18Cr - 10.5Ni - 0.40Ti (SAE 30321) Solution Heat Treated-UNS S32100 |
|
SAE AMS 6514F |
Steel, Maraging, Bars, Forgings, Tubing, and Rings 18.5Ni - 9.0Co - 4.9Mo - 0.65Ti - 0.10Al Consumable Electrode Vacuum Melted, Annealed-UNS K93120 |
|
SAE AMS 6431M |
Steel, Bars, Forgings, and Tubing 1.05Cr - 0.55Ni - 1.0Mo - 0.11V (0.45 - 0.50C) Vacuum Consumable Electrode Remelted-UNS K24728 |
|
SAE AMS 5560L |
Steel, Corrosion Resistant, Seamless Tubing 19Cr - 10Ni (SAE 30304) Solution Heat Treated-UNS S30400 |
|
SAE AMS 5667L |
Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 72Ni - 15.5Cr - 0.95Cb - 2.5Ti - 0.70Al - 7.0Fe Equalized, Precipitation Hardenable-UNS N07750 |
|
SAE AMS 6381G |
Steel, Mechanical Tubing 0.95Cr - 0.20Mo (0.38 - 0.43C) (SAE 4140)-UNS G41400 |
|
SAE AMS 1640B |
Corrosion Removing Compound for Aircraft Surfaces |
|
SAE AMS 3208M |
Chloroprene (CR) Rubber Weather Resistant 45 - 55 |
|
SAE AMS 2610 |
Pressure Testing, Gaseous Media Pressure as Specified |
|
SAE AMS 2253E |
Tolerances Carbon and Alloy Steel Tubing |
|
SAE AMS 4217H |
Aluminum Alloy, Castings 7.0Si - 0.32Mg (356.0-T6) Solution and Precipitation Heat Treated-UNS A03560 |
|
SAE AMS-C-81769 |
Chemical Milling of Metals, Specification for |
|
SAE AMS 2491D |
Surface Treatment of Polytetrafluoroethylene Preparation for Bonding |
|
SAE AMS 5842E |
Cobalt-Nickel Alloy, Corrosion and Heat Resistant, Bars 19Cr - 36Co - 25Ni -7.0Mo - 0.50Cb - 2.9Ti - 0.20Al - 9.0Fe Vacuum Induction Plus Vacuum Consumable Electrode Melted Solution Heat Treated and Work Strengthened-USN R30159 |
|
SAE AMS 5069F |
Steel Bars, Forgings, and Tubing 0.15 - 0.20C (SAE 1018)-UNS G10180 |
|
SAE AMS 3325D |
Fluorosilicone (FVMQ) Rubber Fuel and Oil Resistant 55 - 65 |
|
SAE AMS 5906B |
Steel, Corrosion Resistant, Sheet Strip 18Cr - 9.0Ni (SAE 30302) Cold Rolled, Full Hard, 185 ksi (1276 MPa) Tensile Strength-UNS S30200 |
|
SAE AMS-QQ-A-250/6A |
Aluminum Alloy 5083, Plate and Sheet-UNS A95083 |
|
SAE AMS 2438C |
Plating, Chromium Thin, Hard, Dense Deposit |
|
SAE AMS 3653E |
Tubing, Electrical Insulation Standard Wall, Extruded Polytetrafluoroethylene (PTFE) |
|
SAE AMS 2643D |
Structural Examination of Titanium Alloys Chemical Etch Inspection Procedure |
|
SAE AMS 7267G |
Rings, Sealing, Silicone (VSI) Rubber Heat-Resistant, Low Compression Set 70 - 80 |
|
SAE AMS 5772D |
Cobalt Alloy, Corrosion and Heat Resistant, Bars, Forgings, and Rings 40Co - 22Cr - 22Ni - 14.5W - 0.07La Solution Heat Treated-UNS R30188 |
|
SAE AMS 2810F |
Identification and Packaging Elastomeric Products |
|
SAE AMS 3301G |
Silicone, Rubber General Purpose 40 Durometer |
|
SAE AMS 3411D |
(R) Flux, Silver Brazing High Temperature |
|
SAE AMS 4312C |
Aluminum Alloy, Rolled or Forged Rings 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T651, 6061-T652) Solution Heat Treated, Mechanically Stress Relieved, and Precipitation Heat Treated-UNS A96061 |
|
SAE AMS-QQ-A-200/5A |
Aluminum Alloy 5086, Bar, Rod, Shapes, Tube, and Wire, Extruded-UNS A95086 |
|
SAE AMS 3711E |
Core, Honeycomb Fibrous, Aramid Base, Phenolic Coated |
|
SAE AMS 4772J |
Silver Alloy, Brazing Filler Metal 54Ag - 40Cu - 5.0Zn - 1.0Ni 1325 to 1575 Degrees F (718 to 857 Degrees C) Solidus-Liquidus Range-UNS P07540 |
|
SAE AMS-QQ-A-250/25A |
Aluminum Alloy, Alclad 7075 Plate and Sheet Improved Exfoliation Resistant-UNS A87075 |
|
SAE AMS 3374/1 |
Sealing Compound, One-Part Silicone (Type 1) Aircraft Firewall |
|
SAE AMS 5120L |
Steel Strip 0.68 - 0.80C (SAE 1074)-UNS G10740 |
|
SAE AMS-DTL-23053/15 |
Insulation Sleeving, Electrical, Heat Shrinkable, Polyolefin, Heavy-Wall, Coated, Flexible, Outer Wall Crosslinked-FSC 5970; Should Be Used Instead of MIL-DTL-23053/15B, Which Was Cancelled on 16 September 1999 |
|
SAE AMS 2448 |
Application of Tungsten Carbide Coatings on Ultra High Strength Steels High Velocity Oxygen / Fuel Process |
|
SAE AMS 2451/1A |
Plating, Brush, Nickel General Purpose |
|
SAE AMS 5401C |
Nickel Alloy, Corrosion and Heat-Resistant, Investment Castings 62Ni - 21.5Cr - 9.0Mo - 3.6Cb (Nb) Vacuum Melted, Vacuum Cast As Cast-UNS N26625 |
|
SAE AMS 5656D |
Steel, Corrosion Resistant, Bars, Wire, Forgings, Extrusions, and Rings 9.0Mn - 20Cr - 6.5Ni - 0.27N Solution Heat Treated-UNS S21904 |
|
SAE AMS 2252D |
(R) Tolerances Low-Alloy Steel Sheet, Strip, and Plate |
|
SAE AMS 5637G |
Steel, Corrosion Resistant, Bars and Wire 18Cr - 9.0Ni (SAE 30302) Solution Heat Treated and Cold Drawn 125 ksi (862 MPa) Tensile Strength-UNS S30200 |
|
SAE AMS 4951G |
Titanium Welding Wire Commercially Pure Environment Controlled Packaging-UNS R50550 |
|
SAE AMS 2451/4B |
Plating, Brush, Cadmium Corrosion Protective, Low Hydrogen Embrittlement |
|
SAE AMS 4342E |
Aluminum Alloy, Extrusions 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (7050-T74511) Solution Heat Treated, Stress Relieved, Straightened, and Overaged-UNS A97050 |
|
SAE AMS 4881C |
Nickel-Aluminum-Bronze, Martensitic, Sand and Centrifugal Castings 78Cu - 11Al - 5.1Ni - 4.8Fe Quench Hardened and Temper Annealed |
|
SAE AMS 5595F |
Steel, Corrosion Resistant, Sheet, Strip, and Plate 9.0Mn - 20Cr - 6.5Ni - 0.28N Solution Heat Treated-UNS S21904 |
|
SAE AMS-QQ-A-250/29 |
Aluminum Alloy 2124, Plate-UNS A92124 |
|
SAE AMS 6280K |
Steel Bars, Forgings, and Rings 0.50Cr - 0.55Ni - 0.20Mo (0.28 - 0.33C) (SAE 8630)-UNS G86300 |
|
SAE AMS 5904B |
Steel, Corrosion Resistant, Sheet and Strip 18Cr - 9.0Ni (SAE 30302) Cold Rolled, 1/2 Hard, 150 ksi (1034 MPa) Tensile Strength-UNS S30200 |
|
SAE AMS 5903B |
Steel, Corrosion Resistant, Sheet, Strip, and Plate 18Cr - 9.0Ni (SAE 30302) Cold Rolled, 1/4 Hard, 125 ksi (862 MPa) Tensile Strength-UNS S30200 |
|
SAE AMS 4941D |
Titanium Tubing, Welded Annealed, 40 ksi (276 MPa) Yield Strength-UNS R50400 |
|
SAE AMS 5864B |
Steel, Corrosion-Resistant, Plate 13Cr - 8.0Ni - 2.2Mo - 1.1Al Vacuum Induction Plus Consumable Electrode Melted Solution Heat Treated, Precipitation Hardenable-UNS S13800 |
|
SAE AMS 2768A |
Heat Treatment of Magnesium Alloy Castings |
|
SAE AMS 3902E |
Cloth, Organic Fiber (Para-Aramid), High Modulus for Structural Composites |
|
SAE AMS 5580K |
Nickel Alloy, Corrosion and Heat Resistant, Seamless Tubing 74Ni - 15.5Cr - 8.0Fe Annealed-UNS N06600 |
|
SAE AMS 6395F |
Steel Sheet, Strip, and Plate 0.95Cr - 0.20Mo (0.38 - 0.43C) (SAE 4140)-UNS G41400 |
|
SAE AMS 5515L |
Steel, Corrosion Resistant, Sheet, Strip, and Plate 18Cr - 8.5Ni (302) Solution Heat Treated, High Ductility-UNS S30200 |
|
SAE AMS 4890C |
Copper-Beryllium Alloy Castings 97Cu - 2.1Be - 0.52Co - 0.28Si Solution Heat Treated (TB00)-UNS C82500 |
|
SAE AMS 4982D |
Titanium Alloy Wire 44.5 Cb-UNS R58450 |
|
SAE AMS 2374D |
Quality Assurance Sampling and Testing Corrosion and Heat-Resistant Steel and Alloy Forgings |
|
SAE AMS 3100B |
Adhesion Promoter For Polysulfide Sealing Compounds |
|
SAE AMS 3345E |
Silicone Rubber 1000 psi (6.90 MPa) Tensile Strength 45 - 55 |
|
SAE AMS 2431/3D |
Peening Media (AWCR) Conditioned Carbon Steel Cut Wire Shot, Regular Hardness (45 to 52 HRC) |
|
SAE AMS 6308D |
Steel, Bars and Forgings 0.90Si - 1.0Cr - 2.0Ni - 3.2Mo - 2.0Cu - 0.10V (0.07 - 0.13C) Vacuum Arc or Electroslag Remelted-UNS K71040 |
|
SAE AMS 4341E |
Aluminum Alloy, Extrusions 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (7050-T73511) Solution Heat Treated, Stress Relieved by Stretching, Straightened, and Overaged-UNS A97050 |
|
SAE AMS 2773A |
Heat Treatment Cast Nickel Alloy and Cobalt Alloy Parts |
|
SAE AMS 7257C |
Rings, Sealing, Perfluorocarbon (FFKM) Rubber High Temperature Fluid Resistant 70 - 80 |
|
SAE AMS 2427D |
Aluminum Coating Ion Vapor Deposition |
|
SAE AMS 2261H |
Tolerances Nickel, Nickel Alloy, and Cobalt Alloy Bars, Rods, and Wire |
|
SAE AMS 2263E |
Tolerances Nickel, Nickel Alloy, and Cobalt Alloy Tubing |
|
SAE AMS 4143E |
Aluminum Alloy Forgings and Rolled or Forged Rings 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti (2219-T6) Solution and Precipitation Heat Treated-UNS A92219 |
|
SAE AMS 7273C |
Rings, Sealing, Fluorosilicone (FVMQ) Rubber High Temperature Fuel and Oil Resistant 70 - 80 |
|
SAE AMS 4907H |
Titanium Alloy, Sheet, Strip, and Plate 6.0AL - 4.0V, Extra Low Interstitial Annealed-UNS R56401 |
|
SAE AMS 4782F |
Nickel Alloy, Brazing Filler Metal 71Ni - 10Si - 19Cr 1975 to 2075 °F (1080 to 1135 °C) Solidus-Liquidus Range-UNS N99650 |
|
SAE AMS-QQ-A-200/2A |
Aluminum Alloy 2014, Bar, Rod, Shapes, Tube, and Wire, Extruded-UNS A92014 |
|
SAE AMS-S-4383 |
Sealing Compound, Topcoat, Fuel Tank, Buna-N Type-FSC 8030 |
|
SAE AMS 5347B |
Steel, Corrosion-Resistant, Investment Castings 15Cr - 4.6Ni - 0.22Cb (Nb) - 2.8Cu Solution and Precipitation Heat Treated (H1000) 150 ksi (1034 MPa) Tensile Strength (15-5)-UNS J92110 |
|
SAE AMS 5738D |
Steel, Corrosion-Resistant, Bars and Wire 18Cr - 9Ni (SAE 30303F) Free Machining, High Yield Strength Solution Heat Treated and Cold Worked-UNS S30323 |
|
SAE AMS-QQ-A-591 |
Aluminum Alloy Die Castings |
|
SAE AMS 5687M |
Nickel Alloy, Corrosion and Heat-Resistant, Wire 74Ni - 15.5Cr - 8.0Fe Annealed-UNS N06600 |
|
SAE AMS 5878C |
Nickel Alloy, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 59Ni - 22Cr - 2Mo - 14W - 0.35AI - 0.03La Solution Heat Treated-UNS N06230 |
|
SAE AMS 5350H |
(R) Steel, Corrosion and Moderate Heat Resistant, Investment Castings 12.5Cr (SAE 51410) Hardened and Tempered-UNS J91152 |
|
SAE AMS 4202D |
Aluminum Alloy Plate 5.7Zn - 2.2Mg - 1.6Cu - 0.22Cr (7475-T7351) Solution Heat Treated, Stress Relieved by Stretching, and Precipitation Heat Treated-UNS A97475 |
|
SAE AMS 6327J |
Steel Bars and Forgings 0.50Cr - 0.55Ni - 0.25Mo (0.38 - 0.43C) (SAE 8740) Heat Treated, 125 ksi (862 MPa) Tensile Strength |
|
SAE AMS-QQ-A-250/9A |
Aluminum Alloy 5456, Plate and Sheet-UNS A95456 |
|
SAE AMS 4904A |
Titanium Alloy Sheet, Strip, and Plate 6Al 4V Solution Heat Treated and Aged-R56400 |
|
SAE AMS 4930F |
Titanium Alloy Bars, Wire, Forgings, and Rings 6Al - 4V, Extra Low Interstitial Annealed-UNS R56401 |
|
SAE AMS 4071L |
Aluminum Alloy, Drawn, Round, Seamless Hydraulic Tubing 2.5Mg - 0.25Cr (5052-0) Annealed-UNS A95052 |
|
SAE AMS 5597E |
Nickel Alloy, Corrosion and Heat Resistant, Sheet, Strip, and Plate 52.5Ni - 19Cr - 3.0Mo - 5.1Cb - 0.90Ti - 0.50A1 - 18Fe Consumable Electrode or Vacuum Induction Melted 1950 Degrees F (1066 Degrees C) Solution Heat Treated-UNS N07718 |
|
SAE AMS 5387C |
(R) Alloy, Corrosion and Heat Resistant, Investment Castings 60Co - 29Cr - 4.5W as Cast-UNS R30006 |
|
SAE AMS 3117 |
Primer Zinc Molybdate |
|
SAE AMS 5698G |
Nickel Alloy, Corrosion and Heat-Resistant, Wire 72Ni - 15.5Cr - 0.95Cb - 2.5Ti - 0.70Al - 7.0Fe No. 1 Temper, Precipitation Hardenable-UNS N07750 |
|
SAE AMS 4377H |
Magnesium Alloy, Sheet and Plate 3.0Al - 1.0Zn - 020Mn (AZ31B-H24) Cold Rolled, Partially Annealed-UNS M11311 |
|
SAE AMS-P-83310 |
Plastic Sheet, Polycarbonate, Transparent |
|
SAE AMS 4162D |
Aluminum Alloy, Extrusions 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti (2219-T8511) Solution Treated, Stress Relief Stretched, Straightened, and Precipitation Heat Treated-UNS A92219 |
|
SAE AMS 5503E |
Steel, Corrosion-Resistant, Sheet, Strip, and Plate 17Cr (SAE 51430) Annealed-UNS S43000 |
|
SAE AMS-DTL-23053/10 |
Insulation Sleeving, Electrical, Heat Shrinkable, Silicone Rubber, Flexible-FSC 5970; Should Be Used Instead of MIL-DTL-23053/10D, Which Was Cancelled on 16 September 1999 |
|
SAE AMS-WW-T-700/5A |
Tube, Aluminum Alloy, Drawn, Seamless, 5086 |
|
SAE AMS 2419C |
(R) PLATING, CADMIUM-TITANIUM |
|
SAE AMS 4185D |
Filler Metal, Aluminum Brazing 12Si (4047) |
|
SAE AMS 6346A |
Steel Bars 0.95Cr - 0.20Mo (0.28 to 0.33C) (SAE 4130) Hardened and Tempered, 125 Ksi (862 MPa) Tensile Strength-UNS G41300 |
|
SAE AMS 3352B |
Silicone Rubber, Fiberglass Fabric Reinforced |
|
SAE AMS 4596 |
Copper Nickel Tin Alloy, Bars, Rods, and Tubes 77Cu - 15Ni - 8Sn Solution Annealed and Spinodal Hardened (TX 00)-UNS 72900 |
|
SAE AMS 3356E |
Silicone (VMQ) Rubber Lubricating Oil and Compression Set Resistant, Electrical Grade 55 - 65 |
|
SAE AMS 3410J |
(R) Flux, Silver Brazing |
|
SAE AMS 2629B |
Fluid, Jet Reference-FSC 9130 |
|
SAE AMS 4763A |
Silver Alloy, Brazing Filler Metal 56Ag - 22Cu - 17Zn - 5.0Sn 1145 to 1205 Degrees F (618 to 652 Degrees C) Solidus-Liquidus Range-UNS P07563 |
|
SAE AMS 6425B |
Steel, Bars, Forgings, and Tubing 1.4Mn - 1.5Si - 0.30Cr - 1.8Ni - 0.40Mo (0.23 - 0.28C) Consumable Electrode Vacuum Melted-UNS K32550 |
|
SAE AMS 6448K |
Steel, Bars, Forgings, and Tubing 0.95Cr - 0.22V (0.48 - 0.53C) (SAE 6150)-UNS G61500 |
|
SAE AMS 3044E |
Magnetic Particles, Fluorescent Wet Method, Dry Powder |
|
SAE AMS-QQ-A-250/7A |
Aluminum Alloy 5086, Plate and Sheet-UNS A95086 |
|
SAE AMS 6457C |
Steel, Welding Wire 0.95Cr - 0.20Mo (0.28 - 0.33C) Vacuum Melted, Environmental Controlled Packaging SAE 4130-UNS K13147 |
|
SAE AMS 4291G |
Aluminum Alloy, Die Castings 8.5Si - 3.5Cu (A380.0-F) As Cast-UNS A13800 |
|
SAE AMS 4954H |
Titanium Alloy, Welding Wire 6Al - 4V-UNS R56402 |
|
SAE AMS 5796E |
Cobalt Alloy, Corrosion and Heat Resistant, Welding Wire 52Co - 20Cr - 10Ni - 15W-UNS R30605 |
|
SAE AMS 5911A |
Steel, Corrosion Resistant, Sheet and Strip 19Cr - 9.2Ni (SAE 30304) Cold Rolled, 1/2 Hard, 150 ksi (1034 MPa) Tensile Strength-UNS S30400 |
|
SAE AMS 4931C |
Titanium Alloy Bars, Forgings, and Rings 6Al - 4V Extra Low Interstitial (ELI) Duplex Annealed, Fracture Toughness-UNS R56400 |
|
SAE AMS 5636F |
Steel, Corrosion-Resistant, Bars and Wire 18Cr - 9.0Ni (SAE 30302) Solution Heat Treated and Cold Drawn 100 ksi (689 MPa) Tensile Strength-UNS S30200 |
|
SAE AMS-QQ-A-200/13B |
Aluminum Alloy 7178, Bar, Rod, Shapes, Tube, and Wire, Extruded-UNS A97178 |
|
SAE AMS 2431/8B |
Peening Media (AWCH) Conditioned Carbon Steel Cut Wire Shot, High Hardness (55 to 62 HRC) |
|
SAE AMS 4535C |
Copper-Beryllium Alloy, Mechanical Tubing 98Cu - 1.9Be Solution and Precipitation Heat Treated (TF00, formerly AT)-UNS C17200 |
|
SAE AMS 5902B |
Steel, Corrosion-Resistant, Sheet and Strip 18Cr - 8Ni (SAE 30301) Cold Rolled, 3/4 Hard, 175 ksi (1207 MPa) Tensile Strength-UNS S30100 |
|
SAE AMS 2759/10A |
Automated Gaseous Nitriding Controlled by Nitriding Potential |
|
SAE AMS 5628F |
Steel, Corrosion-Resistant, Bars, Wire, Forgings, and Tubing 16Cr - 2.5Ni (SAE 51431)-UNS S43100 |
|
SAE AMS-QQ-A-225/4 |
Aluminum Alloy, 2014, Bar, Rod, Wire and Special Shapes, Rolled, Drawn, or Cold Finished |
|
SAE AMS 5913A |
Steel, Corrosion Resistant, Sheet and Strip 19Cr - 9.2Ni (SAE 30304) Cold Rolled, Full Hard, 185 ksi (1276 MPa) Tensile Strength-UNS S30400 |
|
SAE AMS 2515E |
Polytetrafluoroethylene (PTFE) Resin Coating Low Build, 370 - 400 Degrees C (698 - 752 Degrees F) Fusion |
|
SAE AMS 4130L |
Aluminum Alloy Die Forgings 4.4Cu - 0.85Si - 0.80Mn (2025-T6) Solution and Precipitation Heat Treated-UNS A 92025 |
|
SAE AMS 5575N |
Steel, Corrosion and Heat Resistant, Welded Tubing 18Cr - 10.5Ni - 0.70Cb(Nb) (SAE 30347) Solution Heat Treated-UNS S34700 |
|
SAE AMS 10135A |
Angle - Bulb Section Extruded-FSC 9540 |
|
SAE AMS 1435A |
Fluid, Generic, Deicing/Anti-Icing Runways and Taxiways-Supersedes SAE AMS 1432 |
|
SAE AMS 4985C |
Titanium Alloy, Investment Castings 6Al - 4V 130 UTS, 120 YS, 6% EL Hot Isostatically Pressed Anneal Optional or When Specified-UNS R56401 |
|
SAE AMS 3644G |
Plastic: Polyimide For Molded Rod, Bar, and Tube, Plaque, and Formed Parts |
|
SAE AMS 5644D |
Steel Bars and Forgings, Corrosion Heat Resistant 17Cr - 7Ni - 1Al-UNS S17700 |
|
SAE AMS-T-8506B |
Tubing, Steel, Corrosion-Resistant, (304), Annealed, Seamless and Welded |
|
SAE AMS 6325H |
Steel, Bars and Forgings 0.50Cr - 0.55Ni - 0.25Mo (0.38 - 0.43C) (SAE 8740) Heat Treated, 105 ksi (724 MPa) Tensile Strength-UNS G87400 |
|
SAE AMS 5346C |
Steel, Corrosion-Resistant, Investment Castings 15Cr - 4.6Ni - 0.22Cb (Nb) - 2.8Cu Solution and Precipitation Heat Treated (H925) 180 ksi (1241 MPa) Tensile Strength (15-5)-UNS J92110 |
|
SAE AMS 5507F |
Steel, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 17Cr - 13Ni - 2.5Mo (SAE 30316L) Solution Heat Treated-UNS S31603 |
|
SAE AMS-T-81914 |
Tubing, Plastic, Flexible, Convoluted, Conduit, General Specification for-Should Be Used for New Designs Instead of MIL-T-81914, Which Was Inactivated for New Design on December 18, 1998 |
|
SAE AMS 6454D |
Steel, Sheet, Strip, and Plate 1.8Ni - 0.80Cr - 0.25Mo (0.38 - 0.43C) (SAE 4340) Vacuum Consumable Electrode Remelted-UNS G43406 |
|
SAE AMS 2477 |
Conversion Coating for Aluminum Alloys Low Electrical Resistance Coating |
|
SAE AMS 4167H |
Aluminum Alloy, Extrusions 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T73511) Solution Heat Treated, Stress Relieved by Stretching, and Overaged-UNS A97075 |
|
SAE AMS 5132K |
Steel, Bars 0.90 - 1.30C |
|
SAE AMS-R-83285 |
Rubber, Ethylene-Propylene, General Purpose |
|
SAE AMS 2825A |
Material Safety Data Sheets |
|
SAE AMS 3110H |
Primer Zinc Chromate |
|
SAE AMS 4631E |
Aluminum Bronze Rods, Bars, and Forgings 90.5 Cu - 7.5 Al - 1.95: Stress Relieved-Reaffirmed Noncurrent April 2006 |
|
SAE AMS 4903A |
Titanium Alloy Sheet, Strip, and Plate 6Al - 4V Solution Heat Treated-UNS R56400 |
|
SAE AMS 2303E |
Steel Cleanliness, Aircraft Quality Martensitic Corrosion-Resistant Steels Magnetic Particle Inspection Procedure |
|
SAE AMS 2431/7A |
Peening Media Ceramic Shot |
|
SAE AMS 4241C |
Aluminum Alloy Castings 7.0Si - 0.58Mg - 0.15Ti - 0.06Be (D357.0-T6) Solution and Precipitation Heat Treated Dendrite Arm Spacing (DAS) Controlled |
|
SAE AMS 4842E |
Castings, Leaded Bronze, Sand and Centrifugal 80Cu - 10Sn - 9.5Pb As Cast |
|
SAE AMS 3650C |
Rods, Sheets, and Molded Shapes, Polychlorotrifluoroethylene (PCTFE) Unplasticized |
|
SAE AMS 4500J |
Copper, Sheet, Strip, and Plate Soft Annealed-UNS C11000 |
|
SAE AMS 6526F |
Steel, Bars, Forgings, Tubing, and Rings 1.0Cr - 7.5Ni - 4.5Co - 1.0Mo - 0.09V (0.29 - 0.34C) Consumable Electrode Vacuum Remelted, Annealed-UNS K91283 |
|
SAE AMS 2685E |
Welding, Tungsten Arc, Inert Gas (GTAW Method) |
|
SAE AMS 3275B |
Sheet, Acrylonitrile Butadiene (NBR) Rubber and Non-Asbestos Fiber Fuel and Oil Resistant |
|
SAE AMS 4942E |
Titanium Tubing, Seamless Annealed, 40.0 ksi (275 MPa) Yield Strength-UNS R50400 |
|
SAE AMS 4991C |
Titanium Alloy Castings, Investment 6Al - 4V Hot Isostatic Pressed, Anneal Optional-UNS R56401 |
|
SAE AMS 5062G |
Steel, Low Carbon Bars, Forgings, Tubing, Sheet, Strip, and Plate 0.25 Carbon, Maximum (Composition similar to UNS K02508) |
|
SAE AMS 2360D |
Room Temperature Tensile Properties of Castings |
|
SAE AMS 3284A |
Sealing Compound, Low Adhesion, for Removable Panels and Fuel Tank Inspection Plates |
|
SAE AMS 3025B |
Polyalkylene Glycol Heat Treat Quenchant |
|
SAE AMS 5907B |
Steel, Corrosion and Heat Resistant, Sheet, Strip, and Plate 17Cr - 12Ni - 2.5Mo (SAE 30316) Cold Rolled, 1/4 Hard, 125 ksi (862 MPa) Tensile Strength-UNS S31600 |
|
SAE AMS-QQ-A-200/7B |
Aluminum Alloy 5456, Bar, Rod, Shapes, Tube, and Wire, Extruded-UNS A95456 |
|
SAE AMS 2642C |
Structural Examination of Titanium Alloys Etch-Anodize Inspection Procedure |
|
SAE AMS 3138D |
Coating Materials, Fluorocarbon (FKM) Elastomeric |
|
SAE AMS-QQ-A-225/10A |
Aluminum Alloy, Bar, Rod, and Wire, Rolled, Drawn, or Cold Finished, 6262-UNS A96262 |
|
SAE AMS-C-83445A |
Coating System, Polyurethane, Nonyellowing, White, Rain Erosion Resistant, Thermally Reflective-FSC 8010 |
|
SAE AMS-DTL-23053/7 |
Insulation Sleeving, Electrical, Heat Shrinkable, Polyethylene Terephthalate, Non-Crosslinked-FSC 5970; Should Be Used Instead of MIL-DTL-23053/7C, Which Was Cancelled on 16 September 1999 |
|
SAE AMS 5697F |
Steel, Corrosion-Resistant, Wire 19Cr - 9.5Ni (SAE 30304) Solution Heat Treated-UNS S30400 |
|
SAE AMS 6932 |
Titanium Alloy Bars, Forgings and Forging Stock 6.0Al - 4.0V Extra Low Interstitial Annealed-UNS R56401 |
|
SAE AMS 2402J |
Plating, Zinc |
|
SAE AMS 4650L |
Copper-Beryllium Alloy, Bars, Rods, Shapes, and Forgings 98Cu - 1.9Be Solution Heat Treated TB00 (A) (Composition similar to UNS C17200) |
|
SAE AMS 3100/1A |
Adhesion Promoter for Polysulfide Sealing Compounds Nonhalogenated Solvent |
|
SAE AMS 5390E |
Nickel Alloy, Corrosion and Heat-Resistant, Investment Castings 47.5Ni - 22Cr - 1.5Co - 9Mo - 0.60W - 18.5Fe (N-12MV) As-Cast-UNS N06002 |
|
SAE AMS 5122H |
Steel Strip (0.90 - 1.04C) (SAE 1095) Hard Temper-UNS G10950 |
|
SAE AMS 5548P |
Steel, Corrosion and Heat Resistant, Sheet and Strip 16.5Cr - 4.5Ni - 2.9Mo - 0.10N 1850 to 1975 Degrees F (1010 to 1079 Degrees C) Annealed-UNS S35000 |
|
SAE AMS 2279A |
Tolerances Rubber Products |
|
SAE AMS 2408H |
Plating, Tin |
|
SAE AMS 5598E |
Nickel Alloy, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 72Ni - 15.5Cr - 0.95 (Cb (Nb) + Ta) - 2.5Ti - 0.70Al - 7.0Fe Consumable Electrode, Remelted or Vacuum Induction Melted, Solution Heat Treated, Precipitation-Hardenable-UNS N07750 |
|
SAE AMS-C-8073 |
Core Material, Plastic Honeycomb, Laminated Glass Fabric Base, for Aircraft Structural and Electronic Applications |
|
SAE AMS 1384A |
Acid, Inhibited Phosphoric Aircraft Turbine Engine Components Room Temperature Application |
|
SAE AMS-G-6032 |
Grease, Plug Valve, Gasoline and Oil Resistant, NATO Code Number G-363, Metric-FSC 9150; Should Be Used Instead of MIL-G-6032D, Which Was Cancelled on 10 September 1999 |
|
SAE AMS 4216B |
Aluminum Alloy, Sheet 1.0Mg - 0.8Si - 0.8Cu - 0.50Mn (6013-T6) Solution Heat Treated and Artificially Aged-UNS A96013 |
|
SAE AMS 5553F |
Nickel, Sheet and Strip Low (0.02 Max) Carbon Annealed-UNS N02201 |
|
SAE AMS 3593A |
Tubing, Plastic, Electrical Insulation Irradiated Polyvinylidene Fluoride, Semi-Rigid, Heat-Shrinkable Marker Sleeving Grade Low Outgassing |
|
SAE AMS 5712J |
Nickel Alloy, Corrosion and Heat Resistant, Bars, Forgings, and Rings 53Ni - 19Cr - 11Co - 9.8Mo - 3.2Ti - 1.6Al - 0.006B Vacuum Melted, Solution Heat Treated Precipitation Hardenable-UNS N07041 |
|
SAE AMS 2753B |
Liquid Salt Bath Ferritic Nitrocarburizing Non-Cyanide Bath |
|
SAE AMS 4914C |
Titanium Alloy Cold Rolled Sheet and Strip 15V - 3Al - 3Cr - 3Sn Solution Heat Treated |
|
SAE AMS 4770K |
Silver Alloy Brazing Filler Metal 50Ag - 18Cd - 16.5Zn - 15.5Cu 1160 to 1175 Degrees F (627 to 635 Degrees C) Solidus-Liquidus Range-UNS P07500 |
|
SAE AMS 4992 |
Castings, Structural Investment, Titanium Alloy 6Al - 4V Hot Isostatically Pressed-UNS R56401 |
|
SAE AMS 3655B |
Tubing, Electrical Insulation Thin Wall, Extruded Polytetrafluoroethylene (PTFE) |
|
SAE AMS 2315F |
Determination of Delta Ferrite Content |
|
SAE AMS 6361E |
Steel Tubing, Seamless 0.95Cr - 0.20Mo (0.28 - 0.33C) (SAE 4130) 125 ksi (862 MPa) Tensile Strength-UNS G41300 |
|
SAE AMS 4774F |
Silver Alloy Brazing Filler Metal 63Ag - 28.5Cu - 6.0Sn - 2.5Ni 1275 to 1475 Degrees F (691 to 802 Degrees C) Solidus-Liquidus Range-UNS P07630 |
|
SAE AMS 3320G |
Silicone (VMQ) Rubber Sheet, Glass Cloth Reinforced Heat and Weather Resistant 60 - 80 |
|
SAE AMS 4173E |
Aluminum Alloy, Extrusions 1.0Mg - 0.60Si - 0.30Cu - 0.20Cr (6061-T6511) Solution Heat Treated, Stress Relieved by Stretching, Straightened, and Precipitation Heat Treated-UNS A96061 |