|
SAE AMS 5316D |
Ductile (Nodular) Iron Castings, Sand 80,000 psi (550 MPa) Tensile Strength as Cast-Reaffirmed Noncurrent May 2005; UNS F34100 |
|
SAE AMS 6250K |
Steel Bars, Forgings, and Tubing 1.5Cr - 3.5Ni (0.07 - 0.13 C) (SAE 3310)-UNS K44910 |
|
SAE AMS-T-81914/5 |
Tubing, Plastic, Extra Flexible, Convoluted, Ethylene-Tetrafluoroethylene, Close Convolution-Should Be Used Instead of MIL-T-81914/5, Which Was Cancelled on December 18, 1998 |
|
SAE AMS 3249C |
Ethylene Propylene (EPDM) Rubber Hydrazine-Base-Fluid Resistant 75 - 85 |
|
SAE AMS 3306B |
Rubber, Silicone 1200 psi (8.27 MPa), High Modulus 55 - 65 |
|
SAE AMS 3901C |
Organic Fiber (Para-Aramid), Yarn and Roving, High Modulus |
|
SAE AMS 4211B |
Alluminum Alloy, Plate 6.2Zn - 1.9Cu - 2.1Mg - 0.10Zr (7040-T7451) Solution Heat Treated, Stress Relieved, and Overaged-UNS A97040 |
|
SAE AMS 5655E |
Steel, Corrosion and Heat Resistant, Bars, Wire, and Forgings 12.5Cr - 0.75Ni - 1.0Mo - 1.0W - 0.24V (0.20-0.25C) Hardened and Tempered-UNS S42200 |
|
SAE AMS-I-83387 |
Inspection Process, Magnetic Rubber |
|
SAE AMS 3193C |
Silicone Rubber Sponge Closed Cell, Medium, Extreme Low Temperature |
|
SAE AMS 4079F |
(R) Aluminum Alloy, Drawn, Round, Seamless, Tubing 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-O) Close Tolerance, Annealed-UNS A96061 |
|
SAE AMS 4164H |
Aluminum Alloy, Extrusions 4.4Cu - 1.5Mg - 0.60Mn (2024-T3510) Stress-Relief Stretched, Unstraightened-UNS A92024 |
|
SAE AMS 5803E |
Steel, Corrosion and Heat-Resistant, Welding Wire 16.4Cr - 4.8Ni - 0.22Cb - 3.6Cu Vacuum Melted-UNS S17480 |
|
SAE AMS 6915 |
Titanium Alloy Bars, Forgings and Forging Stock 7.0Al - 4.0Mo Annealed-UNS R56740 |
|
SAE AMS-PRF-46194A |
FOAM, RIGID, STRUCTURAL, CLOSED CELL |
|
SAE AMS 2980/2A |
Technical Specification: Carbon Fiber Fabric and Epoxy Resin Wet Lay-up Repair Material Part 2 - Qualification Program |
|
SAE AMS 2980/4A |
Carbon Fiber Fabric and Epoxy Resin Wet Lay-Up Repair Material Purchasing Specification - Resin |
|
SAE AMS 3970 |
Carbon Fiber Fabric Repair Prepreg, 125 Degrees Celsius (250 Degrees F) Vacuum Curing Part 0.- Introduction |
|
SAE AMS 4095C |
Aluminum Alloy, Alclad Sheet and Plate 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti Alclad 2219-T31; Sheet, Solution Heat Treated and Cold Worked Alclad 2219-T351; Plate, Solution Heat Treated and Stress Relieved-UNS A82219 |
|
SAE AMS 5875C |
Cobalt Alloy, Corrosion and Heat-Resistant, Strip 20Cr - 15Ni - 40Co - 7.0Mo - 16Fe Solution Heat Treated, Cold Rolled, and Aged Vacuum Induction Plus Vacuum Consumable Electrode Melted-UNS S30003 |
|
SAE AMS 6272K |
Steel Bars, Forgings, and Tubing 0.50Cr - 0.55Ni - 0.20Mo (0.15 - 0.20C) (SAE 8617)-UNS G86170 |
|
SAE AMS 4395E |
Magnesium Alloy Welding Wire 9.0Al - 2.0Zn (AZ92A)-UNS M11922 |
|
SAE AMS 4773F |
Silver Alloy, Brazing Filler Metal 60Ag - 30Cu - 10Sn 1115 to 1325 Degrees F (602 to 718 Degrees C) Solidus-Liquidus Range-UNS P07600 |
|
SAE AMS 5110J |
Carbon Steel, Wire and Springs 0.75 - 0.88C (SAE 1080) Spring Temper, Cold Drawn-UNS G10800 |
|
SAE AMS 5669A |
Alloy Bars, Corrosion and Heat Resistant Nickel Base - 15.5Cr - 0.95 (Cb + Ta) - 2.5Ti - 0.70Al - 7.0Fe Consumable Electrode or Vacuum Induction Melted |
|
SAE AMS 5841E |
Cobalt-Nickel Alloy, Corrosion and Heat Resistant, Bars 19Cr - 36Co - 25Ni - 7.0Mo - 0.50Cb - 2.9Ti - 0.20Al - 9.0Fe Vacuum Induction Plus Vacuum Consumable Electrode Melted Solution Heat Treated for Work Strengthening-UNS R30159 |
|
SAE AMS 6525C |
Steel, Bars, Forgings, Tubing, and Rings 0.75Cr - 9.0Ni - 4.5Co - 1.0Mo - 0.09V (0.17 - 0.23C) Consumable Electrode Vacuum Melted-UNS K91472 |
|
SAE AMS 6906 |
Titanium Alloy Bars, Forgings and Forging Stock 6.0Al - 2.0Sn - 4.0Zr - 6.0Mo Solution Heat Treated and Aged-UNS R 56260 |
|
SAE AMS 3270J |
Chloroprene (CR) Rubber Sheet, Cotton Fabric Reinforced Weather Resistant |
|
SAE AMS 3755B |
Powder, Fumed Silicon Dioxide |
|
SAE AMS 3815D |
Braid, Flat, Nylon, Electrical Tying Synthetic Rubber Coated |
|
SAE AMS 4988A |
Titanium Alloy Sheet, Strip, and Plate 6Al - 6V - 2Sn Solution Heat Treated-UNS R56620 |
|
SAE AMS 7440D |
Balls, Steel, Low-Chromium, High Carbon Hardened and Tempered |
|
SAE AMS 7908B |
Beryllium Near-Net Preforms Standard Grade Hot Isostatic Pressed |
|
SAE AMS 1530B |
Cleaner for Aircraft Exterior Surfaces, Wipe-On, Wipe-Off |
|
SAE AMS 2420D |
Plating of Aluminum for Solderability Zinc Immersion Pre-Treatment Process |
|
SAE AMS 2489 |
Blackening of Steel, Touch Up Method |
|
SAE AMS 2980/5 |
Carbon Fiber Fabric and Epoxy Resin Wet Lay-Up Repair Material Part 5 - Material Specification: Carbon Fiber Fabrics, Plain Weave, 193 g/m2, and Epoxy Resin |
|
SAE AMS 3138/5B |
(R) Coating Material, Fluorocarbon (FKM) Elastomeric Anti-Static Topcoating, White |
|
SAE AMS 3417C |
Flux, Brazing High Temperature |
|
SAE AMS 4094C |
(R) Aluminum Alloy, Sheet and Plate, Alclad 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti Alclad 2219-T81 Sheet Solution Heat Treated, Cold Worked, and Precipitation Heat Treated Alclad 2219-T851 Plate Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated-UNS A822190 |
|
SAE AMS 4255B |
Aluminum Allloy, Clad One Side Sheet 0.6Mg - 0.35Si - 0.28Cu (No. 21 Brazing Sheet) As Fabricated-UNS A86951 |
|
SAE AMS 4484K |
Magnesium Alloy Castings, Permanent Mold 9.0Al - 2.0Zn (AZ92A-T6) Solution and Precipitation Heat Treated-UNS M11920 |
|
SAE AMS 4917F |
Titanium Alloy Sheet, Strip, and Plate 13.5V - 11Cr - 3.0Al Solution Heat Treated-UNS R58010 |
|
SAE AMS 4964A |
Titanium Alloy Bars, Wire, Forgings, and Rings 4.5Al - 3V - 2Fe - 2Mo Annealed |
|
SAE AMS 6255D |
Steel Bars, Forgings, and Tubing 1.1Si - 1.45Cr - 1.0Mo - 0.08Al (0.16 - 0.22C) Double Vacuum Melted |
|
SAE AMS 7464C |
Bolts and Screws, Steel, Low-Alloy Heat-Resistant 220,000 psi (1517 MPa) Tensile Strength Hardened and Tempered, Roll Threaded-Reaffirmed Non-current February 2006 |
|
SAE AMS 7496J |
Rings, Flash Welded Carbon and Low-Alloy Steels |
|
SAE AMS 2451/7A |
Plating, Brush, Nickel Low Stress, Medium-Hardness Deposit |
|
SAE AMS 2667F |
Brazing, Silver For Small Pressurized Fittings |
|
SAE AMS 4134E |
Aluminum Alloy, Die Forgings 4.4Cu - 0.85Si - 0.80Mn - 0.50Mg (2014-T4) Solution Heat Treated-UNS A92014 |
|
SAE AMS 4163D |
Aluminum Alloy, Extrusions 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti (2219-T3511) Solution Heat Treated, Stress-Relieved by Stretching, and Straightened-UNS A92219 |
|
SAE AMS 6925 |
Titanium Alloy Bars, Forgings and Forging Stock 13V - 11Cr - 3Al Solution Heat Treated-UNS R58010 |
|
SAE AMS-I-10 |
Insulation Compound, Electrical, Ceramic, Class L |
|
SAE AMS 3713D |
Core, Flexible Honeycomb, Polyamide Paper Base, Phenolic Coated |
|
SAE AMS 4303B |
Aluminum Alloy Plate 2.7Cu - 2.2Li - 0.12Zr (2090-T81) Solution Heat Treated, Cold Worked, and Aged |
|
SAE AMS 4750D |
Solder, Tin-Lead 45Sn - 55Pb |
|
SAE AMS 5341C |
Steel Castings, Investment, Corrosion Resistant 19.5Cr - 10.5Ni - 0.25S (Type 303) Solution Heat Treated-UNS J92711 |
|
SAE AMS 5572H |
Steel, Corrosion and Heat-Resistant, Seamless Tubing 25Cr - 20Ni (SAE 30310S) Solution Heat Treated-UNS S31008 |
|
SAE AMS 5600E |
Steel, Corrosion Resistant, Sheet Laminated, Edge Bonded-UNS S30200 |
|
SAE AMS 5755F |
Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 64Ni - 5.0Cr - 24.5Mo - 5.5Fe Solution Heat Treated-UNS N10004 |
|
SAE AMS 5789D |
Cobalt Alloy, Corrosion and Heat Resistant, Welding Wire 54Co - 25.5Cr - 10.5Ni - 7.5W-UNS R30031 |
|
SAE AMS 7241C |
Washers, Spring Lock, Corrosion Resistant Steel 18Cr - 19Ni |
|
SAE AMS-QQ-A-200/17A |
Aluminum Alloy 6162, Bar, Rod, Shapes, Tube, and Wire, Extruded-UNS A96162 |
|
SAE AMS 2550E |
Treatment of Sheet Metal Parts Corrosion-Resistant Steel |
|
SAE AMS 2662 |
Brazing, Gold-Nickel Alloy Filler Metal |
|
SAE AMS 3145C |
Paint, Marking Epoxy-REAF Non-current Feb 2004 |
|
SAE AMS 3714D |
Core, Overexpanded Honeycomb, Polyamide Paper Base, Phenolic Coated |
|
SAE AMS 4510G |
Phosphor Bronze, Sheet, Strip, and Plate 94.5Cu - 4.0Sn - 0.19P Spring Temper (H08)-UNS C51000 |
|
SAE AMS 5863D |
Steel, Corrosion Resistant, Sheet, Strip, and Plate 15Cr - 6.5Ni - 0.75Mo - 0.60Cb - 1.5Cu Solution Heat Treated, Precipitation Hardenable-UNS S45000 |
|
SAE AMS-S-29574 |
Sealing Compound, Polythioether, for Aircraft Structures, Fuel and High Temperature Resistant, Fast Curing at Ambient and Low Temperatures |
|
SAE AMS 3143A |
Powder Coating Materials, Epoxy |
|
SAE AMS 3222G |
Synthetic Rubber Hot Oil Resistant, High Swell 45 - 55 |
|
SAE AMS 3273E |
Chloroprene (CR) Rubber Sheet, Nylon Cloth Reinforced Weather Resistant |
|
SAE AMS 3307C |
Rubber, Silicone (VMQ) Low Compression Set, Non-Oil-Resistant 65 - 75 |
|
SAE AMS 4168J |
Aluminum Alloy, Extrusions 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T6510) Solution Heat Treated, Stress Relieved by Stretching, and Precipitation Heat Treated, Unstraightened-UNS A97075 |
|
SAE AMS 4200B |
Aluminum Alloy Plate 7.7Zn - 2.4Mg - 1.6Cu - 0.16Cr (7049-T7351) Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated |
|
SAE AMS 4205C |
Aluminum Alloy, Plate 6.2Zn - 1.8Cu - 2.4Mg - 0.13Zr (7010-T73651) or (7010-T7451) Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated-UNS 97010 |
|
SAE AMS 4232A |
Aluminum Alloy Extrusions 2.7Cu - 2.2Li - 0.12Zr (2090-T86) Solution Heat Treated, Cold Worked, and Precipitation Heat Treated-UNS A92090 |
|
SAE AMS 4314D |
(R) Aluminum Alloy Rings, Rolled or Forged 4.5Cu - 0.85Si - 0.80Mn - 0.50Mg (2014-T651, 2014-T652) Solution Heat Treated, Mechanically Stress Relieved, and Precipitation Heat Treated |
|
SAE AMS 4352H |
(R)Magnesium Alloy, Extrusions 5.5Zn - 0.45Zr (ZK60A-T5) Precipitation Heat Treated-UNS M16600 |
|
SAE AMS 4505J |
Copper Alloy (Brass), Sheet, Strip, and Plate 70Cu - 30Zn Annealed (OS035)-UNS C26000 |
|
SAE AMS 4897B |
Titanium Alloy, Sheet and Strip 79Ti - 15Mo - 3.0AI - 2.8Cb - 0.20Si-UNS R58210 |
|
SAE AMS 5805G |
Steel, Corrosion and Heat Resistant, Welding Wire 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.004B - 0.30V Vacuum Induction Melted, Environment Controlled Packaging-UNS S66286 |
|
SAE AMS 6263K |
Steel Bars, Forgings, and Tubing 1.2Cr - 3.2Ni - 0.12Mo (0.11 - 0.17C) (SAE 9315)-UNS G93150 |
|
SAE AMS 7240F |
Washers, Spring Lock Carbon Steel |
|
SAE AMS-QQ-A-250/22B |
Aluminum Alloy, 7178-T76, Alclad Plate and Sheet, Improved Exfoliation Resistant-UNS A87178 |
|
SAE AMS 1453 |
Disinfectant Cleaner for Aircraft Interior General Purpose Liquid |
|
SAE AMS 3645C |
Polychlorotrifluoroethylene (PCTFE), Compression Molded Heavy Sections, Unplasticized |
|
SAE AMS 3720B |
Paper Honeycomb 60 lb (25 kg) Paper |
|
SAE AMS 4207B |
Aluminum Alloy Sheet, Alclad 5.7Zn - 2.2Mg - 1.6Cu - 0.22Cr (7475- T61) Solution and Precipitation Heat Treated |
|
SAE AMS 4785G |
Gold-Palladium-Nickel Alloy, Brazing Filler Metal, High Temperature 30Au - 34Pd - 36Ni 2075 to 2130 °F (1135 to 1166 °C) Solidus-Liquidus Range-UNS P00300 |
|
SAE AMS 5050K |
Steel Tubing, Seamless 0.15 Carbon, Maximum Annealed-UNS G10100 |
|
SAE AMS 5077F |
Steel Tubing, Welded (0.22 - 0.28C) (SAE 1025) Normalized or Stress Relieved-UNS G10250 |
|
SAE AMS 5764E |
Steel, Corrosion-Resistant, Bars, Wire, Forgings, Extrusions, and Rings 5.0Mn - 22Cr - 12.5Ni - 2.2Mo - 0.20Cb - 0.30N - 0.20V Solution Heat Treated-UNS S20910 |
|
SAE AMS-C-22542 |
Cleaning Compound, High Pressure Cleaner, Liquid-FSC 6850; Should Be Used Instead of MIL-C-22542B(AS), Which Was Cancelled on 21 September 1998 |
|
SAE AMS-R-83412/1 |
Rubber, Ethylene-Propylene, Hydrazine Resistant, O-Rings Sizes and Tolerances-FSC 5330 |
|
SAE AMS 2436D |
Coating, Aluminum Oxide Detonation Deposition |
|
SAE AMS 3357G |
Rubber, Silicone (VMQ) Lubricating Oil and Compression Set Resistant 65 - 75 |
|
SAE AMS 3681C |
Adhesive, Electrically Conductive Silver-Filled Epoxy Resin |
|
SAE AMS 3901/2C |
(R) Yarn, Organic Fiber (Para-Aramid), High Modulus OY 390 (2689)/23.8 Tensile Strength, 17.5 (121)/950 Tensile Modulus 380 Denier, (420 d tex), 0.6% Finish |
|
SAE AMS 4048L |
(R) Aluminum Alloy Sheet and Plate, Alclad 5.6Zn - 2.5Mg - 1.6Cu - 0-23Cr (Alclad 7075-0) Annealed-UNS A87075 |
|
SAE AMS 4298 |
Aluminum Alloy, Alclad Sheet 3.8Cu - 1.0Mg - 0.30Mn - 0.60Zn (Alclad 2056-T3) Solution Heat Treated and Cold Worked |
|
SAE AMS 4761A |
Silver Alloy Brazing Filler Metal 38Ag - 32Cu - 28Zn - 2.0Sn 1200 to 1330 Degrees F (649 to 721 Degrees C) Solidus-Liquidus Range-UNS P07380 |
|
SAE AMS 4784F |
Gold-Palladium-Nickel Alloy, Brazing Filler Metal, High Temperature 50Au - 25Pd - 25Ni 2015 to 2050 °F (1102 to 1121 °C) Solidus-Liquidus Range-UNS P00500 |
|
SAE AMS 5061F |
Steel, Low Carbon, Bars and Wire 0.08 to 0.20 C (Composition similar to UNS K00802) |
|
SAE AMS 5555D |
Nickel Wire and Ribbon 99Ni-UNS N02205 |
|
SAE AMS 2466A |
Hard Anodic Coating of Magnesium Alloys Alkaline Type, High Voltage |
|
SAE AMS 3138/4B |
(R) Coating Material, Fluorocarbon (FKM) Elastomeric Anti-Static Topcoating, Black |
|
SAE AMS 3217/4A |
Test Slabs, Fluoroelastomer (FKM) 65 - 75 |
|
SAE AMS 3414E |
Flux, Aluminum Welding |
|
SAE AMS 3751B |
Microspheres, Hollow Glass |
|
SAE AMS 4281F |
(R) Aluminum Alloy Castings, Permanent Mold 5.0Si - 1.2Cu - 0.50Mg (355.0- T6) Solution and Precipitation Heat Treated-UNS A03550 |
|
SAE AMS 4349D |
Core, Honeycomb, Aluminum Alloy, Corrosion Inhibited for Sandwich Construction, 5056, 350 (177) |
|
SAE AMS 5221E |
Iron-Nickel Alloy Strip 49Fe - 5.3Cr - 42Ni - 2.5Ti - 0.55Al Solution Heat Treated-UNS N09902 |
|
SAE AMS 5614E |
Steel, Corrosion and Heat Resistant, Bars, Wire, and Forgings 12Cr - 0.50Mo Annealed-UNS S41025 |
|
SAE AMS 5672C |
Steel Wire, Corrosion Resistant 11.8Cr - 8.5Ni - 0.30(Cb + Ta) - 1.1Ti - 2.0Cu Precipitation Hardenable, Spring Temper-UNS S45500 |
|
SAE AMS-S-7420B |
Steel Bars, Alloy, Chromium, High Carbon E52100 (Aircraft Quality) |
|
SAE AMS-T-81533A |
Trichloroethane 1, 1, 1, (Methyl Chloroform) Inhibited, Vapor Degreasing |
|
SAE AMS-T-81914/7 |
Tubing, Plastic, Flexible, Convoluted, Fluorinated Ethylene Propylene, Integral Braid-FSC 5975; Should Be Used Instead of MIL-T-81914/7(AS), Which Was Inactivated for New Design on 31 August 1999 |
|
SAE AMS 3726/3A |
Shims, Filled Resin Compound Liquid Precatalyzed |
|
SAE AMS 4337A |
Aluminum Alloy, Extruded Profiles (7055-T77511) 8.0Zn - 2.3Cu - 2.0Mg - 0.16Zr Solution Heat Treated, Stress Relieved, and Overaged-UNS A97055 |
|
SAE AMS 5351F |
Steel Castings, Sand, Corrosion and Moderate Heat Resistant 13Cr Normalized and Tempered |
|
SAE AMS 5577H |
Steel, Corrosion and Heat Resistant, Welded Tubing 25Cr - 20Ni (SAE 30310) Solution Heat Treated-UNS S31008 |
|
SAE AMS 5919 |
Cobalt-Nickel Alloy, Corrosion and Heat-Resistant, Round Bars 19Cr - 36Co - 25Ni - 7.0Mo - 0.50Cb - 2.9Ti - 0.20Al - 9.0Fe Vacuum Induction Plus Vacuum Consumable Electrode Melted Solution Heat Treated and Work Strengthened, Modified Strength-UNS R30159 |
|
SAE AMS 7290F |
Decalcomanias |
|
SAE AMS 1650C |
Polish, Aircraft Metal |
|
SAE AMS 2361D |
Elevated Temperature Tensile Properties of Castings |
|
SAE AMS 2819A |
Identification, Welding Wire Direct Color Code System |
|
SAE AMS 3043C |
Magnetic Particles, Nonfluorescent Wet Method, Oil Vehicle, Aerosol Packaged |
|
SAE AMS 4180G |
Aluminum Wire 99.0A1 Minimum (1100-H18) |
|
SAE AMS 5638F |
Steel, Corrosion-Resistant, Bars and Forgings 0.14S - 18Cr - 9.5Ni - 0.50Mo - 0.80Al (303MA) Free-Machining; Swaging or Upsetting Solution Heat Treated-Composition similar to UNS S30345 |
|
SAE AMS 6270N |
Steel, Bars, Forgings, and Tubing 0.50Cr - 0.55Ni - 0.20Mo (0.13 - 0.18C) (SAE 8615)-UNS G86150 |
|
SAE AMS 6461J |
Steel, Welding Wire 0.95Cr - 0.20V (0.28 - 0.33C) (SAE 6130) Vacuum Melted, Environment Controlled Packaging-UNS K13148 |
|
SAE AMS-I-538 |
Insulation, Electrical, Pasted-Mica-FSC 5640 |
|
SAE AMS 2756A |
Gas Nitriding of Steel Parts-Reaffirmed Noncurrent May 2005 |
|
SAE AMS 3167B |
(R)Solvents, Wipe for Cleaning Prior to Application of Primer and Top Coat Materials, or Sealing Compounds |
|
SAE AMS 3377 |
Sealing Compound, Electrically Conductive Corrosion Inhibiting |
|
SAE AMS 3635D |
Plastic Sheet and Strip, Modified Vinyl, Foamed Closed Cell |
|
SAE AMS 3657C |
Polytetrafluoroethylene Extrusions Premium Strength, as Sintered |
|
SAE AMS 3726/2A |
Shims, Filled Resin Compound Precatalyzed Sheet |
|
SAE AMS 4028G |
Aluminum Alloy Sheet and Plate 4.4Cu - 0.85Si - 0.80Mn - 0.50Mg (2014-0) Annealed |
|
SAE AMS 5774E |
Steel, Corrosion and Heat-Resistant, Welding Wire 16.5Cr - 4.5Ni - 2.9Mo - 0.10N-UNS S35080 |
|
SAE AMS 5834C |
Cobalt Alloy, Corrosion and Heat-Resistant, Round Wire 20Cr - 15Ni - 40Co - 7.0Mo - 16Fe Vacuum Induction Plus Consumable Electrode Melted Solution Heat Treated, Cold Drawn, and Aged-UNS R30003 |
|
SAE AMS 5870D |
Nickel Alloy, Corrosion and Heat Resistant, Sheet, Strip, and Plate 60.5Ni - 23Cr - 14Fe - 0.35Ti - 1.4Al Solution Heat Treated-UNS N06601 |
|
SAE AMS-QQ-W-428/1A |
Wire, Steel, High Carbon, Round, Type I |
|
SAE AMS 2376D |
Qualification, Approval, and Control of Premium-Quality Forgings Alloy Steels and Heat-Treatable Corrosion and Heat Resistant Steels and Alloys-Reaffirmed Noncurrent April 2003 |
|
SAE AMS 3614B |
Polycarbonate Sheet and Parts Optical Grade, Coated |
|
SAE AMS 3670/5C |
Polyamide-Imide Bar, Rod, and Shapes 30% Carbon Fiber |
|
SAE AMS 3686A |
Adhesive, Polyimide Resin, Film and Paste High Temperature Resistant, 315 Degrees C (599 Degrees F) |
|
SAE AMS 3798B |
Webbing, Low Modulus Aramid |
|
SAE AMS 5868B |
Steel, Corrosion Resistant, Seamless and Welded Aircraft Tubing 19Cr - 9.5Ni (SAE 30304) Cold Drawn, 1/2 Hard Temper-UNS S30400 |
|
SAE MAM 2242D |
Tolerances, Metric Corrosion and Heat Resistant Steel, Iron Alloy, Titanium, and Titanium Alloy Sheet, Strip, and Plate |
|
SAE MAM 2279A |
Tolerances, Metric; Rubber Products |
|
SAE AMS 2399A |
Electroless Nickel-Boron Plating-Reaffirmed Noncurrent May 2005 |
|
SAE AMS 2407E |
Plating, Chromium, Porous-Reaffirmed Noncurrent May 2005 |
|
SAE AMS 2415H |
Plating, Lead and Indium |
|
SAE AMS 2814F |
Packaging and Marking of Packages of Welding Wire Premium Quality |
|
SAE AMS 3217/2B |
Test Slabs, Acrylonitrile Butadiene (NBR-L) Low Acrylonitrile, 65 - 75 |
|
SAE AMS 3330A |
Fluorosilicone (FVMQ) Rubber Fuel and Oil Resistant 45 - 55 |
|
SAE AMS 3638F |
Tubing, Irradiated Polyolefin Plastic, Electrical Insulation Pigmented, Semi-Rigid, Heat Shrinkable, 2 to 1 Shrink Ratio |
|
SAE AMS 3894/1B |
Carbon Fiber Tape and Sheet Epoxy Resin Impregnated G 110,000 (758) Tensile, 27,000,000 (186) Modulus, 175 (347) |
|
SAE AMS 4023E |
Aluminum Alloy Sheet and Plate, Alclad 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (Alclad 6061; -T6 Sheet, -T651 Plate)-Reaffirmed Noncurrent November 2004 |
|
SAE AMS 4251 |
Aluminum Alloy Sheet 2.7Cu - 2.2Li - 0.12Zr (2090-T83) Solution Heat Treated, Cold Worked, and Precipitation Heat Treated |
|
SAE AMS 5368D |
Steel, Corrosion-Resistant, Investment Castings 15Cr - 4.0Ni - 2.3Mo - 0.09N Solution Heat Treated |
|
SAE AMS 5410A |
(R) Nickel Alloy, Corrosion and Heat Resistant, Investment Castings 61Ni- 16Cr - 8.5Co - 1.8Mo - 2.6W - 0.85Cb - 3.4Ti - 1.8Ta - 3.4Al - 0.010B - 0.05Zr Vacuum Melted, Vacuum Cast, as Cast or Solution Treated, or Solution and Precipitation Hardened |
|
SAE AMS 5750C |
Alloy Bars, Forgings, and Rings, Corrosion and Heat Resistant Nickel Base - 15.5Cr - 16Mo - 3.8W - 5.5Fe Solution Heat Treated-Reaffirmed Noncurrent April 2006 |
|
SAE AMS 6459D |
Steel, Welding Wire 1.0Cr - 1.0Mo - 0.12V (0.18 - 0.23C) Vacuum Melted-UNS K22720 |
|
SAE AMS-T-81914/3 |
Tubing, Plastic, Flexible, Convoluted, Fluorinated Ethylene Propylene, Standard Convolution-FSC 9330; Should Be Used Instead of MIL-T-81914/3(AS), Which Was Inactivated for New Design on 31 August 1999 |
|
SAE AMS 3084B |
Lubricant, Solid Film Minimal Outgassing |
|
SAE AMS 3090A |
Lubricant, Dry Film, Heat Cured, for Fasteners Polysulfide Sealant Compatible |
|
SAE AMS 3107A |
Primer, Adhesive, Corrosion-Inhibiting for High Durability Structural Adhesive Bonding-FSC 8040 |
|
SAE AMS 3217/1B |
Test Slabs, Acrylonitrile Butadiene (NBR-H) Medium-High Acrylonitrile, 65 - 75 |
|
SAE AMS 3382C |
Tetrafluoroethylene/Propylene Rubber (FEPM) Hydraulic Fluid and Synthetic Oil Resistant 70 to 80 and 85 to 95 |
|
SAE AMS 3680C |
Insulation, Thermal Silica Fiber |
|
SAE AMS 3692C |
Adhesive Compound, Epoxy Resin High Temperature Application |
|
SAE AMS 3817D |
Nylon Braid, Flat Electrical Tying Resin Coated |
|
SAE AMS 4021G |
(R) ALUMINUM ALLOY, ALCLAD SHEET AND PLATE, 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (Alclad 6061-0) Annealed |
|
SAE AMS 4893C |
Alloy Castings, Corrosion and Heat Resistant 66Ni - 29Cu - 4.0Si Solution Treated-UNS N04019 |
|
SAE AMS 5631E |
Steel, Corrosion Resistant, Bars and Forgings 17Cr (0.60 - 0.75C)-UNS S44002 |
|
SAE AMS 5702D |
Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 41.5Ni - 16Cr - 37Fe - 2.9Cb (Nb) - 1.8Ti Consumable Electrode Remelted or Vacuum Induction Melted 1750 Degrees F (954 Degrees C) Solution Heat Treated-UNS N09706 |
|
SAE AMS 5800F |
Nickel Alloy, Corrosion and Heat-Resistant, Welding Wire 54Ni - 19Cr - 11Co - 10Mo - 3.2Ti - 1.5Al - 0.006B Vacuum Induction Melted-UNS N07041 |
|
SAE AMS 6324G |
Steel Bars, Forgings, and Tubing 0.65Cr - 0.70Ni - 0.25Mo (0.38 - 0.43C) (SAE 8740 Modified)-UNS K11640 |
|
SAE AMS 6352H |
Steel Sheet, Strip, and Plate 0.95Cr - 0.20Mo (0.33 - 0.38C) (SAE 4135)-UNS G41350 |
|
SAE AMS 7902E |
Beryllium Sheet and Plate 98Be-UNS R19801 |
|
SAE AMS 3607F |
Plastic Sheet Cotton Fabric Reinforced Phenol-Formaldehyde |
|
SAE AMS 3756A |
Moldings, Glass Fiber Filled Polytetrafluoroethylene 75 PTFE Resin, 25 Glass, as Sintered |
|
SAE AMS 3901/11B |
(R) Yarn, Organic Fiber (Para-Aramid), High Modulus OY 390 (2689)/23.8 Tensile Strength, 16.5 (114)/950 Tensile Modulus 1420 (1580 d tex) Denier, 1.2% Finish |
|
SAE AMS 4490H |
Magnesium Alloy Castings, Die 9.0Al - 0.70Zn (AZ91D, Temper F) As Cast-Composition similar to UNS M11916 |
|
SAE AMS 4532F |
Copper-Beryllium Alloy, Sheet and Strip 98Cu - 1.9Be Half Hard (TD02) |
|
SAE AMS 4959D |
Titanium Alloy Wire 13.5V - 11Cr - 3Al Spring Temper-UNS R58010 |
|
SAE AMS 5348B |
Steel Castings, Tubular, Centrifugal, Corrosion Resistant 15Cr - 4.6Ni - 0.22 (Cb+Ta) - 2.8Cu Solution Heat Treated |
|
SAE AMS 5676F |
Nickel Alloy, Corrosion and Heat-Resistant, Welding Wire 80Ni - 20Cr-UNS N06003 |
|
SAE AMS 7849D |
Tantalum Sheet, Strip, and Plate Annealed-UNS R05210 |
|
SAE AMS 2451/13 |
Plating, Brush, Silver |
|
SAE AMS 3376A |
Sealing Compound, Non-Curing, Groove Injection Temperature and Fuel Resistant |
|
SAE AMS 3695 |
Adhesive Film, Epoxy-Base for High Durability Structural Adhesive Bonding |
|
SAE AMS 4313C |
Aluminum Alloy, Rolled or Forged Rings 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti (2219-T351, 2219-T352) Solution Heat Treated and Mechanically Stress Relieved-UNS A92219 |
|
SAE AMS 5032G |
Wire, Steel 0.18 - 0.23C (SAE 1020) Annealed-Composition similar to UNS G10200 |
|
SAE AMS 5337D |
Steel, Maraging, Investment Castings 18.5Ni - 9.0Co - 5.0Mo - 0.70Ti - 0.12Al Vacuum Melted Homogenized, Overaged, and Solution Heat Treated-UNS J93150 |
|
SAE AMS 5554E |
Steel, Corrosion and Heat Resistant, Seamless Tubing 16.5Cr - 4.5Ni - 2.9Mo - 0.10N Annealed-UNS S35000 |
|
SAE AMS 5694H |
Steel, Corrosion and Heat-Resistant, Welding Wire 27Cr - 21.5Ni-UNS S31080 |
|
SAE AMS 5701D |
Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 41.5Ni - 16Cr - 37Fe - 2.9Cb (Nb) - 1.8Ti Consumable Electrode Remelted or Vacuum Induction Melted 1800 °F (982 °C) Solution Heat Treated |
|
SAE AMS 5716H |
Iron-Nickel Alloy, Heat Resistant, Bars, Wire, Forgings, and Rings 44Fe - 18.5Cr - 35.5Ni - 1.1Si Solution Heat Treated-UNS N08330 |
|
SAE AMS 5838E |
Nickel Alloy, Corrosion and Heat-Resistant, Welding Wire 65Ni - 16Cr - 15Mo - 0.30Al - 0.06La-UNS N06635 |
|
SAE AMS 5873E |
Nickel Alloy, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 65Ni - 15.8Cr - 15.2Mo - 0.30AI - 0.05La Consumable Electrode Remelted, Solution Heat Treated-UNS N06635 |
|
SAE AMS 5937 |
Steel, Corrosion-Resistant, Bars, Wire, and Forgings 12Cr - 11Ni - 2Mo - 1.5Al - 0.3Ti Vacuum Induction Plus Vacuum Consumable Electrode Melted Solution Heat Treated, Precipitation Hardenable |
|
SAE AMS 5966A |
Nickel Alloy, Corrosion and Heat Resistant, Welding Wire 50Ni - 20Cr - 20Co - 5.9Mo - 2.2Ti - 0.45Al Consumable Electrode or Vacuum Induction Melted-UNS N07263 |
|
SAE AMS 6374C |
Steel Tubing, Seam-Free, Round 0.95Cr - 0.20Mo (0.28 - 0.33C) (SAE 4130) 95.0 ksi (655 MPa) Tensile Strength-UNS G41300 |
|
SAE AMS 1545A |
Cleaner, Thrust Reverser Alkaline, Water-Base |
|
SAE AMS 2478E |
Anodic Treatment of Magnesium Alloys Acid Type, Full Coat |
|
SAE AMS 3041D |
Magnetic Particles, Nonfluorescent Wet Method, Oil Vehicle, Ready-to-Use |
|
SAE AMS 3161B |
Oil, Odorless Heavy Solvent |
|
SAE AMS 3333 |
Sealing Compound, Polysulfide for Aircraft Windshields aand Canopies, for Use up to 250 Degrees F (121 Degrees C) |
|
SAE AMS 3623D |
Tubing, Irradiated Polychloroprene Elastomer, Electrical Insulation Flexible, Heat-Shrinkable, 1.750 to 1 Shrink Ratio |
|
SAE AMS 3673B |
Cloth, Glass Aluminum Face, Silicone Rubber Back |
|
SAE AMS 4209B |
Aluminum Alloy Sheet, Alclad 6.0Cu - 0.40Zr - (2004-F) As Rolled-UNS A82004 |
|
SAE AMS 4221B |
Aluminum Alloy, Plate 4.4Cu - 1.5Mg - 0.60Mn (2124-T8151) Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated-UNS A92124 |
|
SAE AMS 4223D |
Aluminum Alloy, Castings 4.5Cu - 0.70Ag - 0.30Mn - 0.25Mg - 0.25Ti (A201.0-T4) Solution Heat Treated and Naturally Aged |
|
SAE AMS 4242B |
Aluminum Alloy, Castings 4.7Cu - 0.60Ag - 0.35Mn - 0.25Mg - 0.25Ti (B201.0-T7) Solution Heat Treated and Overaged |
|
SAE AMS 4800E |
Bearings, Babbitt 91Sn - 4.5Sb - 4.5Cu |
|
SAE AMS 4987C |
Titanium Alloy, Forgings 10V - 2Fe - 3AI Consumable Electrode Melted, Single Solution Heat Treated and Overaged 140 ksi (965 MPa) Tensile Strength |
|
SAE AMS 5339F |
Steel, Maraging, Investment Castings 17Ni - 10Co - 4.6Mo - 0.30Ti - 0.06Al Vacuum Melted Homogenized, Overaged, and Solution Heat Treated-UNS J93010 |
|
SAE AMS 5371E |
Steel Castings, Sand, Corrosion and Heat Resistant 19.5Cr - 9.5Ni (Low Carbon) (304L) Solution Heat Treated-UNS J92620 |
|
SAE AMS 6481B |
Steel Bars, Forgings, and Tubing, Nitriding 3Cr - 1Mo - 0.2V - (0.29 - 0.36C) Premium Aircraft-Quality for Bearing Applications Double Vacuum Melted-UNS K24340 |
|
SAE AMS 1426C |
Fluid, Deicing/Anti-Icing, Runways and Taxiways Glycol Base |
|
SAE AMS 3042D |
Magnetic Particles, Nonfluorescent Wet Method, Dry Powder |
|
SAE AMS 3066C |
Compound, Corrosion-Inhibiting Water-Displacing, Soft Film, Aerosol Canned |
|
SAE AMS 3136E |
Coating Material, Phenolic Resin, PTFE Filled Pigmented, 150 °C (302 °F) Cure |
|
SAE AMS 3283A |
Sealing Compound, Polysulfide Non-Curing, Groove Injection Temperature and Fuel Resistant |
|
SAE AMS 3348C |
Silicone (VMQ) Rubber 1150 psi (7.93 MPa) Tensile Strength, High Resiliency 25 - 35 |
|
SAE AMS 4125J |
Aluminum Alloy Die Forgings, and Rolled or Forged Rings 0.9Si - 0.62Mg - 0.25Cr (6151-T6) Solution and Precipitation Heat Treated-UNS A 96151 |
|
SAE AMS 4172E |
Aluminum Alloy, Extrusions 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T4511) Solution Heat Treated and Stress Relieved by Stretching-UNS A96061 |
|
SAE AMS 4204C |
Aluminum Alloy, Plate 6.2Zn - 1.8Cu - 2.4Mg - 0.13Zr (7010-T7651) Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated-UNS A97010 |
|
SAE AMS 4237B |
Aluminum Alloy Castings, Sand 4.6Cu - 0.35Mn - 0.25Mg - 0.22Ti (206.0 -T71) Solution Heat Treated and Naturally Aged-UNS A02060 |
|
SAE AMS 5053H |
Steel Tubing, Welded 0.13 Carbon, Maximum Annealed-UNS G10100 |
|
SAE AMS 5593F |
Nickel Alloy, Corrosion and Heat Resistant, Sheet, Strip, and Plate 45.5Ni - 25.5Cr - 3.2Co - 3.2Mo - 3.2W - 18.5Fe Solution Heat Treated-UNS N06333 |
|
SAE AMS 5745F |
Steel, Corrosion and Heat-Resistant, Bars and Forgings 16.5Cr - 4.5Ni - 2.9Mo - 0.10N Equalized and Over-Tempered-UNS S35000 |
|
SAE AMS 5794E |
Iron Alloy, Corrosion and Heat-Resistant, Welding Wire 31Fe - 21Cr - 20Ni - 20Co - 3.0Mo - 2.5W - 1.0Cb - 0.15N Annealed-UNS R30155 |
|
SAE AMS 5812F |
Steel, Corrosion and Heat Resistant, Welding Wire 15Cr - 7.1Ni - 2.4Mo - 1.0Al Vacuum Melted-UNS S15789 |
|
SAE AMS 6372K |
Steel Tubing, Mechanical 0.95Cr - 0.20Mo (0.33 - 0.38C) (SAE 4135)-UNS G41350 |
|
SAE AMS 6501D |
Steel, Maraging, Welding Wire 18Ni - 8.0Co - 4.9Mo - 0.40Ti - 0.10Al Vacuum Induction Melted, Environment Controlled Packaging-UNS K92890 |
|
SAE AMS 1383A |
Oxide Conditioner, Alkaline Permanganate Aircraft Turbine Engine Components |
|
SAE AMS 3227G |
Acrylonitrile Butadiene (NBR) Rubber Hot Oil and Coolant Resistant, Low Swell 55 - 65 |
|
SAE AMS 3678/2 |
Type 2 15% Graphite Filled Virgin Polytetrafluoroethylene (PTFE) Moldings or Extrusions |
|
SAE AMS 4012F |
Aluminum Sheet, Laminated Edge Bonded-Reaffirmed Noncurrent April 2006 |
|
SAE AMS 5027E |
Steel, Welding Wire 1.05Cr - 0.55Ni - 1.0Mo - 0.08V (0.26 - 0.32C) Vacuum Melted, Environment-Controlled Packaging-UNS K22925 |
|
SAE AMS 5830C |
Nickel-Iron Alloy, Corrosion and Heat-Resistant, Welding Wire 12.5Cr - 42.5Ni - 6.0Mo - 2.7Ti - 0.015B - 35Fe-UNS N09901 |
|
SAE AMS 6428H |
Steel, Bars, Forgings, and Tubing 0.80Cr-1.8Ni-0.35Mo-0.20V(0.32-0.38C) (4335 Modified)-UNS K23477 |
|
SAE AMS 6488H |
Steel, Bars and Forgings 5.0Cr - 1.3Mo - 0.5V - (0.38 - 0.43C)-UNS T20811 |
|
SAE AMS 7727E |
Iron-Nickel-Cobalt Alloy, Bars and Forgings 53Fe - 29Ni - 17Co Low Expansion, Glass Sealing-UNS K94610 |
|
SAE AMS 7880C |
Tungsten Carbide-Cobalt Powder Sintered and Crushed |
|
SAE AMS-P-21600 |
Paint System, Fluorescent, Removable, for Aircraft Application |
|
SAE AMS 3250J |
Synthetic Rubber and Cork Composition General Purpose Soft |
|
SAE AMS 3670/2B |
Polyamide-Imide Bar, Rod, and Shapes 20 Graphite - 3 Polytetrafluorethylene (PTFE) Filled |
|
SAE AMS 3726/1B |
Shims, Filled Resin Compound Liquid |
|
SAE AMS 4069D |
Aluminum Alloy, Drawn, Round Seamless Tubing Close Tolerance 2.5Mg - 0.25Cr (5052-0) Annealed-UNS A95052 |
|
SAE AMS 4148E |
Aluminum Alloy Die Forgings (7175-T66) Solution and Precipitation Heat Treated-UNS A97175 |
|
SAE AMS 4320B |
Aluminum Alloy Forgings 7.7Zn - 2.5Mg - 1.5Cu - 0.16Cr (7149-T73) Solution and Precipitation Heat Treated-UNS A97149 |
|
SAE AMS 4508H |
Copper-Zinc Alloy, Laminated Sheet 70Cu - 30Zn Surface Bonded-UNS C26000 |
|
SAE AMS 4898B |
Titanium Alloy, Sheet 6Al - 2Sn - 2Zr - 2Mo - 2Cr - 0.15Si Annealed |
|
SAE AMS 4924F |
Titanium Alloy Bars, Forgings, and Rings 5Al - 2.5Sn, Extra Low Interstitial Annealed-UNS R54521 |
|
SAE AMS 2451/12 |
Plating, Brush, Tin |
|
SAE AMS 3631C |
(R) Polyvinyl Chloride (PVC) Plastic Extrusions High Temperature, Flexible |
|
SAE AMS 3690B |
Adhesive Compound, Epoxy Room Temperature Curing |
|
SAE AMS 3970/1 |
Carbon Fiber Fabric Repair Prepreg, 125 Degrees Celsius (250 Degrees F) Vacuum Curing Part 1.- General Requirements |
|
SAE AMS 4332 |
Aluminum Alloy, Extruded Profiles (7349-T76511) 8.1Zn - 1.7Cu - 2.2Mg - 0.16Zr Solution Heat Treated, Stress-Relieved, and Overaged |
|
SAE AMS 4396E |
Magnesium Alloy Welding Wire 3.3Ce - 2.5Zn - 0.72Zr (EZ33A)-UNS M12331 |
|
SAE AMS 4994A |
Titanium Alloy Powdered Metal Products 6Al - 4V Hot Isostatically Pressed, Annealed-UNS R56400 |
|
SAE AMS 5583D |
Nickel Alloy, Corrosion and Heat-Resistant, Seamless Tubing 72Ni - 15.5Cr - 0.95Cb - 2.5Ti - 0.70Al - 7.0Fe Vacuum Melted Solution Heat Treated, Precipitation Hardenable to 170 ksi (1172 MPa) Tensile Strength-UNS N07750 |
|
SAE AMS 5840D |
Steel, Corrosion and Heat Resistant, Welding Wire 13Cr - 8.0Ni - 2.3Mo - 1.1Al Vacuum Melted-UNS S13889 |
|
SAE AMS 6340 |
Steel Bars, Forgings, and Tubing 0.88Cr - 1.8Ni - 0.42Mo - 0.08V (0.28 - 0.33C) Consumable Electrode Vacuum Remelted-UNS K23080 |
|
SAE AMS 3242G |
Chloroprene (CR) Rubber Weather Resistant 75 - 85 |
|
SAE AMS 3329A |
Fluorosilicone (FVMQ) Rubber Fuel and Oil Resistant, High Strength 45 - 55 |
|
SAE AMS 3373B |
Compound, Silicone Rubber, Insulating and Sealing 35 to 55 |
|
SAE AMS 3383 |
Polytetrafluoroethylene (PTFE) - Fluorosilicone (FVMQ) Rubber High Temperature Fuel and Oil Resistant 75 - 85 |
|
SAE AMS 4453D |
Magnesium Alloy, Investment Castings 9.0Al - 2.0Zn (AZ92A-T6) Solution and Precipitation Heat Treated-UNS M11920 |
|
SAE AMS 4827E |
Bearings, Leaded Bronze 80Cu - 10Pb - 10Sn Steel Back |
|
SAE AMS 5334H |
Steel, Investment Castings 0.50Cr - 0.55Ni - 0.20Mo (0.25 - 0.35C) (SAE 8630 Mod) Normalized and Tempered-UNS J13042 |
|
SAE AMS 5340D |
(R) Steel, Corrosion Resistant, Investment Castings 14Cr - 4.25Ni - 2.25Mo - 0.25Cb - 3.25Cu Homogenization and Solution Heat Treated-UNS J92240 |
|
SAE AMS 5607E |
Nickel Alloy, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 73Ni - 7.0Cr - 16.5Mo Solution Heat Treated-UNS N10003 |
|
SAE AMS-I-7068A |
Ingot, Zinc Alloy (for Sheet Metal Forming Dies) |
|
SAE AMS-S-83474 |
Shims, Molded, Filled Resin Compound and Sheet Prepreg |
|
SAE AMS 1370 |
Compound, Rust Remover, Liquid Aircraft and Aerospace Components, Immersion Tank Method |
|
SAE AMS 1534B |
Cleaner, Aircraft Glass Window |
|
SAE AMS 2479D |
Anodic Treatment of Magnesium Alloys Acid Type, Thin Coat |
|
SAE AMS 3901/4C |
(R) Yarn, Organic Fiber (Para-Aramid), High Modulus OY 390 (2689)/23.8 Tensile Strength, 16.5 (114)/955 Tensile Modulus 1420 Denier (1580 d tex), 0.6% Finish |
|
SAE AMS 4501D |
Copper Sheet, Strip, and Plate Oxygen-Free, Light Cold Rolled-UNS C10200 |
|
SAE AMS 5070H |
Steel, Bars and Forgings 0.18 - 0.23C (SAE 1022)-UNS G10220 |
|
SAE AMS 5578G |
Steel, Corrosion and Heat-Resistant, Welded Tubing 12Cr - 8.5Ni - 0.30Cb - 1.1Ti - 2.0Cu Vacuum Induction Plus Consumable Electrode Vacuum Melted Solution Heat Treated, Precipitation Hardenable-UNS S45500 |
|
SAE AMS 2514A |
Anodic Coating on Aluminum Alloys Sulfuric Acid Process, Resin-Sealed |
|
SAE AMS 3159F |
Leak Test Solution Liquid Oxygen Compatible |
|
SAE AMS 3378A |
Sealant, Silicone, Two-Part, General Purpose Room Temperature Vulcanizing Non-Fuel Resistant |
|
SAE AMS 3637F |
Tubing, Irradiated Polyolefin Plastic, Electrical Insulation Clear, Flexible, Heat Shrinkable 2 to 1 Shrink Ratio |
|
SAE AMS 3647C |
Polyfluoroethylene Propylene Film and Sheet |
|
SAE AMS 3658C |
Polytetrafluoroethylene Extrusions Premium Strength, Sintered and Stress-Relieved Radiographically Inspected |
|
SAE AMS 3678/9A |
Type 9 Virgin Polytetrafluoroethylene (PTFE) Moldings with Pigment for AS4716 and AS5857 Backup Rings |
|
SAE AMS 3729A |
Epoxy Resin Matrix, Thermosetting Moderate Temperature Resistant, Unfilled |
|
SAE AMS 3894E |
Carbon Fiber Tape and Sheet Epoxy Resin Impregnated |
|
SAE AMS 3970/3 |
Carbon Fiber Fabric Repair Prepreg, 125 Degrees Celsius (250 Degrees F) Vacuum Curing Part 3 - Purchasing Specification for Epoxy Prepreg |