SAE AMS 4086N

Aluminum Alloy, Drawn, Round, Seamless Hydraulic Tubing 4.4Cu - 1.5Mg - 0.60Mn (2024-T3) Solution Heat Treated, Cold Worked, and Naturally Aged

SAE AMS 4822E

Bearings, Leaded Bronze 71.5Cu - 25Pb - 3.0Sn Steel Back

SAE AMS 5028D

Steel, Welding Wire 1.05Cr - 0.55Ni - 1.0Mo - 0.07V (0.34 - 0.40C) Vacuum Melted, Environment-Controlled Packaging-UNS K23725

SAE AMS 5358C

Steel Castings, Investment, Corrosion Resistant 18Cr - 9Ni Solution Heat Treated-UNS J92602; Reaffirmed Noncurrent September 2007

SAE AMS 5372D

Steel Castings, Sand, Corrosion Resistant 16Cr - 1.9Ni (Type 431 Mod) Normalized and Tempered-UNS J91601

SAE AMS 5821G

Steel, Corrosion-Resistant, Welding Wire 12Cr (SAE 51410 Modified) Ferrite Control Grade-UNS S41081

SAE AMS 5887B

Nickel Alloy, Corrosion and Heat Resistant, Bars, Forgings, and Rings 54Ni - 22Cr - 12.5Co - 9.0Mo - 1.2Al Consumable Electrode or Vacuum Induction Melted Annealed-UNS N06617

SAE AMS 6474

Forgings, Hardenable Steels and Corrosion- Resistant Steels Heat- Treated, Finished-Part Properties Short- Transverse Tensile Strength and Fracture Toughness

SAE AMS-T-6735B

Tubing, Chrome-Molybdenum, 4135 Steel, Seamless Aircraft Quality

SAE AMS 2224G

Tolerances Copper and Copper Alloy Wire

SAE AMS 2409G

Plating, Immersion Tin for Aluminum Alloys

SAE AMS 3180F

Toluene, Industrial Grade

SAE AMS 3286E

Felt, Firm Pad, White 100% Wool

SAE AMS 3605F

Plastic Sheet, Post- Forming Cotton Fabric Reinforced Phenol- Formaldehyde

SAE AMS 3813A

Rope, Aramid Fiber, Jacketed for Antenna- Support Systems

SAE AMS 4114H

Aluminum Alloy Bars and Rods, Rolled or Cold-Finished 2.5Mg - 0.25Cr (5052-F) As Fabricated-UNS A95052

SAE AMS 4316

Aluminum Alloy, Alclad Sheet and Plate 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr 7075: (-T76 Sheet, -T7651 Plate) Solution and Precipitation Heat Treated-UNS R87075

SAE AMS 5696C

Steel, Corrosion and Heat-Resistant, Welding Wire 19Cr - 12.5Ni - 2.5Mo High Ferrite Grade-UNS S31683

SAE AMS 6452C

Steel, Welding Wire 0.95Cr - 0.20Mo (0.38 - 0.43C) Vacuum Melted, Environment Controlled Packaging-UNS G41400

SAE AMS 7205F

Spring Pins, Tubular Carbon Steel

SAE AMS-S-7947B

Steel, Sheet and Strip (1095) (Aircraft Quality)

SAE AMS 1374A

Remover, Polyurethane/Epoxy Paint Alkaline, Hot-Tank Type

SAE AMS 1427A

Deicing/Anti-Icing Fluid, Aircraft, Propylene Glycol Base

SAE AMS 3107/3A

Primer, Adhesive, Corrosion-Inhibiting High Durability Epoxy, -55 to +175 °C (-67 to +347 °F)

SAE AMS 3116A

Primer Coating; Epoxy, Chemical and Solvent Resistant Non-Chromated, Corrosion Preventive

SAE AMS 3217A

Standard Elastomer Stocks Test Slabs

SAE AMS 3253

Ethylene Propylene Rubber Phosphate Ester Resistant 65 - 75

SAE AMS 4295B

Aluminum Alloy, Sheet and Plate 6.3Cu - 0.30Mn - 0.06Ti - 0.10V - 0.18Zr (2219 - O, F, T31, T351, T37, T81, T851, T87)-UNS A92219

SAE AMS 4324

Aluminum Alloy, Extruded Rod, Bar and Profiles (7055-T74511) 8.0Zn - 2.3Cu - 2.0Mg - 0.16Zr Solution Heat Treated, Stress-Relieved, and Overaged-UNS A97055

SAE AMS 4330B

Aluminum Alloy, Plate (2297-T87) 2.8Cu - 1.5Li - 0.30Mn - 0.12Zr Solution Heat Treated, Stretched, and Artificially Aged-UNS A92297

SAE AMS 4612J

Brass, Naval, Bars and Rods 60.5Cu - 38.5Zn - 0.75Sn Hard Temper (H04)

SAE AMS 4932B

Titanium Alloy Sheet 6Al - 4V Driver Sheet-UNS R56400

SAE AMS 1625B

Desmutter, Aluminum, Powdered

SAE AMS 2362C

Stress-Rupture Properties of Castings

SAE AMS 2510E

Engine Gray Finishing Low Baking-Reaffirmed Noncurrent November 2004; Supersedes AMS 25100

SAE AMS 3262

Sealing Compound, Silicon Rubber, Two-Part, Electrically Conductive and Corrosion Resistant (Nonchromated) for Use from -67 to 500 Degrees F (-55 to 260 Degrees C)

SAE AMS 3335D

Silicone Rubber Extreme Low-Temperature Resistant 45 - 55-Reaffirmed Noncurrent April 2001

SAE AMS 3412E

Flux, Aluminum Brazing for Torch or Furnace Brazing

SAE AMS 3420F

Dehydrating Agent Silica Gel

SAE AMS 3642D

Plastic Moldings, Laminated, Thermosetting Resin Glass Cloth Reinforced Heat Resistant

SAE AMS 3870D

Ceramic Moldings and Extrusions Dense, Ultra-High Alumina (99% A1203)

SAE AMS 4267

Aluminum Alloy, Sheet (7055-O) 8.0Zn - 2.3Cu - 2.0Mg - 0.16Zr Annealed-UNS A97055

SAE AMS 4280H

(R) Aluminum Alloy Castings, Permanent Mold 5.0Si - 1.2Cu - 0.5Mg (355.0-T71) Solution Heat Treated and Overaged-UNS A03550

SAE AMS 4297A

Aluminum Alloy Sheet 4.4Cu - 1.5Mg - 0.60Mn (2024; -T4 Flat Sheet) Solution Heat Treated, High Formability-UNS A92024

SAE AMS 5550E

Alloy Sheet, Strip, and Plate, Corrosion and Heat Resistant 80Ni - 15.5Cr - 0.62ti - 3.25Al Annealed

SAE AMS 5804G

Steel, Corrosion and Heat-Resistant, Welding Wire 15Cr - 25.5Ni - 1.3Mo - 2.2Ti - 0.006B - 0.30V-UNS S66286 and K66286

SAE AMS 6365J

Steel Tubing, Seamless 0.95Cr - 0.20Mo (0.33 - 0.38C) (SAE 4135) Normalized or Stress Relieved-UNS G41350

SAE AMS 6429F

Steel Bars, Forgings, Tubing, and Rings 0.78Cr - 1.8Ni - 0.35Mo - 0.20V (0.33 - 0.38C) Consumable Electrode Vacuum Melted-Composition similar to UNS K33517

SAE AMS 6543D

Steel, Bars and Forgings, Maraging 2.0Cr - 10Ni - 8.0Co - 1.0Mo (0.10 - 0.14C)(HY-180) Double Vacuum Melted, Solution Heat Treated-UNS K91970

SAE AMS 1385A

Compound, Hot Carbon and Paint Remover Aircraft Turbine Engine Components

SAE AMS 3091C

Mold Release Agent

SAE AMS 3140A

Coating, Urethane, Aliphatic Isocyanate Polytetrafluoroethylene Filled

SAE AMS 3368A

Silicone Resin, Elastomeric, Transparent Elevated Temperature Cure

SAE AMS 3619C

Resin, Polyimide, Laminating High Temperature Resistant, 315 Degrees C (599 Degrees F)

SAE AMS 3678/7

Type 7 Virgin Polytetrafluoroethylene (PTFE) Moldings or Extrusions with 25% Carbon and Graphite

SAE AMS 3679B

Insulation, Thermal Ceramic Fiber

SAE AMS 3787A

Thread, Para-Aramid Intermediate Modulus-FSC 8310

SAE AMS 3821B

Cloth, Type

SAE AMS 3847C

Cloth, Quartz,

SAE AMS 3897

Cloth, Carbon Fiber, Resin Impregnated

SAE AMS 4066C

Aluminum Alloy, Drawn, Round Seamless Tubing 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti - (2219-T8511) Solution Heat Treated, Stress Relieved by Stretching and Precipitation Heat Treated-UNS A92219

SAE AMS 4424K

Magnesium Alloy Castings, Sand 6.0A1 - 3.0Zn (AZ63-T6) Solution and Precipitation Heat Treated

SAE AMS 4949

Titanium, Sheet, Laminated, Surface Bonded

SAE AMS 5546D

Steel Sheet and Strip, Corrosion and Moderate Heat Resistant 16.5Cr - 4.5Ni - 2.9Mo - 0.10N Cold Rolled, Temperedq

SAE AMS 5797D

Cobalt Alloy, Corrosion and Heat-Resistant, Covered Welding Electrodes 51.5Co - 20Cr - 10Ni - 15W-UNS W73605

SAE AMS 5888B

Nickel Alloy, Corrosion and Heat Resistant, Plate 54Ni - 22Cr - 12.5Co - 9.0Mo - 1.2Al Annealed-UNS N06617

SAE AMS 6281J

Steel, Mechanical Tubing 0.50Cr - 0.55Ni- 0.20Mo (0.28 - 0.33C) (SAE 8630)-UNS G86300

SAE AMS-T-81914/6

Tubing, Plastic, Flexible, Convoluted, Ethylene-Tetrafluoroethylene, Standard Convolution-FSC 9330; Should Be Used Instead of MIL-T-81914/6(AS), Which Was Inactivated for new Design on 31 August 1999

SAE AMS 2465C

Disilicide Diffusion Coating of Molybdenum and Molybdenum Alloys Pack Cementation Method

SAE AMS 2467

Hard Anodic Coating of Magnesium Alloys Alkaline Type, High Voltage

SAE AMS 3226G

Acrylonitrile Butadiene (NBR) Rubber Hot Oil and Coolant Resistant, Low Swell 45 - 55

SAE AMS 3237F

Butyl (IIR) Rubber Phosphate Ester Resistant 35 - 45

SAE AMS 3582A

Plastic Tubing, Electrical Insulation Crosslinked Polyvinyl Chloride, Flexible Heat Shrinkable 2 to 1 Shrink Ratio

SAE AMS 3603A

(R) Protective Film, High Performance, Polymeric Pressure Sensitive Adhesive, for Aircraft Exterior Applications

SAE AMS 3798/2B

Webbing, Low Modulus Aramid 1 (25) Wide, 600 (2669) Breaking Strength Herringbone Twill

SAE AMS 4183

Aluminum Alloy, Extruded Profiles (2027-T3511) 4.4Cu 1.2Mg - 0.8Mn 0.10Zr Solution Heat Treated and Stress Relieved by Stretching-UNS A92027

SAE AMS 4455E

Magnesium Alloy, Investment Castings 10Al (AM100A-T6) Solution and Precipitation Heat Treated-UNS M10100

SAE AMS 4899B

Titanium Alloy, Sheet, Strip, and Plate 4.5AI - 3V - 2Fe - 2Mo Annealed-UNS R54700

SAE AMS 4966M

Titanium Alloy, Forgings 5Al - 2.5Sn Annealed, 110 ksi (758 MPa) Yield Strength-UNS R54520

SAE AMS 5635F

Steel, Corrosion-Resistant, Bars, Wire, and Forgings 18Cr - 9Ni - 0.21Pb (303Pb) Free-Machining, Solution Heat Treated-UNS S30360

SAE AMS 5836B

Nickel Alloy, Corrosion and Heat-Resistant, Welding Wire 72Ni - 3.0Mn - 20Cr - 2.5Cb-UNS N06082

SAE AMS 5964

Nickel Alloy, Corrosion and Heat-Resistant, Welding Wire Ni - 18Cr - 2.8Mo - 5.5Cb(Nb) - 0.70Ti - 1.50Al - 10Fe - 9Co - 1W Consumable Electrode Remelted or Vacuum Induction Melted-UNS N07818

SAE AMS 7256A

Rings, Sealing, Tetrafluoroethylene/Propylene Rubber (FEPM) Hydraulic Fluid and Synthetic Oil Resistant 85 to 95

SAE AMS 1452B

Disinfectant, Aircraft, General Purpose

SAE AMS 2451/10A

Plating, Brush, Tin-Zinc Low Hydrogen Embrittlement

SAE AMS 3170G

Thinner, Alcohol-Ester

SAE AMS 3229G

Acrylonitrile Butadiene (NBR) Rubber Hot Oil Resistant, Low Swell 75 - 85-Includes Revision F; Reaffirmed Noncurrent November 2003

SAE AMS 3239E

Butyl (IIR) Rubber Phosphate Ester Resistant 85 - 95

SAE AMS 3251H

Synthetic Rubber and Cork Composition General Purpose Medium

SAE AMS 3285E

Felt, Back Check, White 100% Wool

SAE AMS 4089D

Aluminum Alloy, Plate 1.6Cu - 2.2Mg - 0.22Cr - 5.7Zn (7475-T7651) Solution Heat Treated, Stress Relieved by Stretching, and Precipitation Heat Treated-UNS A97475

SAE AMS 4334A

Aluminum Alloy, Forgings 7.8Zn - 2.2Mg - 1.6Cu - 0.15Cr (7249-T74 and -T7452)

SAE AMS 4764F

Copper Alloy, Brazing Filler Metal 52.5Cu - 38Mn - 9.5Ni 1615 to 1700 °F (879 to 927 °C) Solidus-Liquidus Range-UNS C69950

SAE AMS 5389C

Alloy Castings, Sand, Corrosion and Heat Resistant 55Ni - 16.5Cr - 17Mo - 4.5W - 5.8Fe - 0.40V Solution Heat Treated-UNS N10002

SAE AMS 5652G

Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Tubing, and Rings 25Cr - 20Ni - 2.0Si (SAE 30314) Solution Heat Treated-UNS S31400

SAE AMS 5771E

Nickel Alloy, Corrosion and Heat Resistant, Bars, Forgings, and Rings 74Ni - 7.0Cr - 16.5Mo Solution Heat Treated-UNS N10003

SAE AMS 6292G

Steel Bars and Forgings, Carburizing 1.8Ni - 0.25Mo (0.15 - 0.20C) (SAE 4617)-UNS G46170

SAE AMS 6462H

Steel, Welding Wire 0.95Cr - 0.20V (0.28 - 0.33C) (SAE 6130)-UNS K13149

SAE AMS 7266B

Rings, Sealing, Fluorocarbon Rubber General Purpose, High Temperature, Fuel and Oil Resistant 65 - 75

SAE AMS 7510/1B

Magnets, Rare-Earth/Cobalt, Permanent Samarium-Cobalt, 33/67 - 15 (119) 250

SAE AMS-T-9046B

Titanium and Titanium Alloy, Sheet, Strip, and Plate-FSC 9535; Supereded by SAE AMS 4901, AMS 4900, AMS 4902, AMS 4940, AMS 4910, AMS 4909, AMS 4915, AMS 4916, AMS 4911, AMS 4903, AMS 4904, AMS 4907, AMS 4918, AMS 4988, AMS 4990, AMS 4919, AMS 4989, AMS 4917 and AMS 4939

SAE AMS 1425C

Deicing Fluid, Aircraft Ethylene Glycol Base

SAE AMS 1540B

Cleaner, Thrust Reverser, Water-Base

SAE AMS 2451/5A

Plating, Brush, Chromium Hard Deposit, Trivalent

SAE AMS 2451/8A

Plating, Brush, Non-Cyanide Silver General Purpose

SAE AMS 2506D

Coating of Fasteners Aluminum Filled, Ceramic Bonded Coating

SAE AMS 2633C

Ultrasonic Inspection Centrifugally-Cast, Corrosion-Resistant Steel Tubular Cylinders

SAE AMS 3107/1A

Primer, Adhesive, Corrosion-Inhibiting High Durability Epoxy, -55 Degrees to +95 Degrees C (-67 Degrees to +203 Degrees F)

SAE AMS 3366B

Silicone Rubber Compound Room Temperature Vulcanizing, 55,000 Centipoise Viscosity Durometer 55 - 70

SAE AMS 3901/10B

(R) Yarn, Organic Fiber (Para-Aramid), High Modulus OY 390 (2689)/23.9 Tensile Strength, 16.5 (114)/945 Tensile Modulus 1140 Denier (1270 d tex), 1.2% Finish

SAE AMS 4090D

Aluminum Alloy, Plate 5.7Zn - 2.2Mg - 1.6Cu - 0.22Cr (7475-T651) Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated-UNS A97475

SAE AMS 4244A

(R) Aluminum Alloy, Welding Wire 4.6Cu - 0.35Mn - 0.25Mg - 0.22Ti for Welding A206.0 Type Alloys

SAE AMS 4300C

Boron-Aluminum Composite Sheet 50 v/o 5.6B, 6061-0, For Diffusion Bonding

SAE AMS 4315

Aluminum Alloy Sheet and Plate 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr 7075: (-T76 Sheet, -T7651 Plate) Solution and Precipitation Heat Treated-UNS R97075

SAE AMS 4406

Aluminum Alloy, Centrifugal Castings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (709.0-T61) Hot Isostatically Pressed, Solution and Precipitation Heat Treated

SAE AMS 4675C

Nickel-Copper Alloy, Corrosion Resistant, Bars and Forgings 67Ni - 30Cu-UNS N04400

SAE AMS 4766G

Silver Alloy, Brazing Filler Metal 85Ag - 15Mn 1760 Degrees to 1780 Degrees F (960 Degrees to 971 Degrees C) Solidus-Liquidus Range-UNS P07850

SAE AMS 4998C

Titanium Alloy Powder 6Al - 4V-UNS R56400

SAE AMS 5369E

Steel Castings, Sand, Corrosion and Heat Resistant 19.5Cr - 9.5Ni - 1.4Mo - 1.4W - 0.50 (Cb+Ta) - 0.32Ti Solution and Precipitation Heat Treated-UNS J92843

SAE AMS 5523F

Steel, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 23Cr - 13.5Ni (SAE 30309S) Solution Heat Treated-UNS S30908

SAE AMS 5850D

Steel, Corrosion and Heat Resistant, Honeycomb Core Resistance Welded, Square Cell

SAE AMS 6303G

Steel Bars and Forgings, Low Alloy, Heat-Resistant 0.65Si - 1.25Cr - 0.50Mo - 0.85V (0.25 - 0.30C)

SAE AMS 6354F

Steel, Sheet, Strip, and Plate 0.75Si - 0.62Cr - 0.20Mo - 0.10Zr (0.10 - 0.17C)-UNS K11914

SAE AMS 7322E

Rings, Sealing, Cast Tin Bronze 80Cu - 19Sn As Cast

SAE AMS 7912B

Aluminum-Beryllium Alloy, Extrusions 38Al - 62Be Annealed

SAE AMS-STD-2175A

Castings, Classification and Inspection of-AREA NDTI; Should Be Used Instead of MIL-STD-2175A, Which Was Cancelled on 10 November 1999

SAE AMS 1386A

Compound, Silicone Rubber Remover Aircraft Turbine Engine Components Room Temperature Application

SAE AMS 2414G

Plating, Lead

SAE AMS 3107/4A

Primer, Adhesive, Corrosion-Inhibiting High Durability Epoxy, -55 to +215 °C (-67 to +419 °F)

SAE AMS 3258

Sealing Compound, Polythioether for Aircraft Windshields and Canopies, for Use up to 300 Degrees F (149 Degrees C)

SAE AMS 3571/5B

Resin, Polyether Urethane (EU) Casting Flexible, Solid, Unfilled 85 Durometer

SAE AMS 3609D

Methyl Methacrylate Plastic, Sheet Heat Resistant

SAE AMS 3712C

Core, Honeycomb, Glass/Polyimide

SAE AMS 3912A

Radomes, Foam Sandwich Polyimide/Quartz Cloth Construction

SAE AMS 4087H

Aluminum Alloy Tubing, Seamless, Drawn (2024-0) Reinstate Composition Annealed

SAE AMS 4186C

(R) Aluminum Alloy Bars, Rods, and Wire, Rolled or Cold Finished 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-F) As Fabricated-UNS A97075

SAE AMS 4323B

Aluminum Alloy, Hand Forgings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T7452) Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated-UNS A97075

SAE AMS 4732D

Copper-Nickel Alloy Wire and Ribbon 77.5Cr - 22.5Ni-UNS C71110

SAE AMS 6435E

Steel, Sheet, Strip, and Plate 0.75Mn - 0.78Cr - 1.8Ni - 0.35Mo - 0.20V (0.33 - 0.38C)(SAE 4335 Mod) Vacuum Consumable Electrode Melted, Annealed-UNS K33517

SAE AMS 7510/2B

Magnets, Rare-Earth/ Cobalt, Permanent Samarium-Cobalt, 33/67 - 18 (143) 250

SAE AMS 7719D

Nickel-Iron Alloy, Magnetic, Sheet and Strip 50Ni - 50Fe Stamping Quality-UNS K95000

SAE AMS 3571/1B

Resin, Polyether Urethane (EU) Casting Flexible, Solid, Unfilled 45 Durometer

SAE AMS 3625B

Elastomeric Tubing, Electrical Insulation Crosslinked Silicone, Pigmented, Flexible, Heat-Shrinkable 1.750 to 1 Shrink Ratio

SAE AMS 3813/1A

Rope, Aramid Fiber, Jacketed Cabled Strand, Extruded Jacket

SAE AMS 3827B

Cloth, Type

SAE AMS 3970/2

Carbon Fiber Fabric Repair Prepreg, 125 Degrees Celsius (250 Degrees F) Vacuum Curing Part 2 - Qualification Program for Fiber, Fabric, Resin and Film Adhesive

SAE AMS 3970/4

Carbon Fiber Fabric Repair Prepreg, 125 Degrees Celsius (250 Degrees F) Vacuum Curing Part 4 - Purchasing Specification for Film Adhesive adhesive

SAE AMS 4243B

Aluminum Alloy, Alclad Sheet 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (Alclad 7050-T76) Solution Heat Treated and Overaged-UNS A87050

SAE AMS 4387E

Magnesium Alloy Extrusions 2.3Zn - 0.62Zr (ZK21A-F) As Extruded-UNS M16210

SAE AMS 4871F

Aluminum Bronze, Centrifugal and Chill Castings 85Cu - 11Al - 3.6Fe Solution Heat Treated and Tempered-UNS C95420

SAE AMS 5625D

Steel Bars, High Expansion 9.5Ni - 5.5Mn (0.55 - 0.65C) Cold Finished-UNS K91456; FSC 9510; Reaffirmed Noncurrent November 2004

SAE AMS 5768K

Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 21Cr - 20Ni - 20Co - 3.0Mo - 2.5W - 1.0Cb - 0.15N - 31Fe Solution and Precipitation Heat Treated-UNS R30155

SAE AMS 5892A

Alloy, Sheet and Strip 42Fe - 37.5Ni - 14Co - 4.8(Cb + Ta) - 1.6Ti Solution Heat Treated, Precipitation Hardenable Multiple Melted, High Temperature, Low Expansion-UNS N19909

SAE AMS 6412L

Steel, Bars and Forgings 0.80Cr - 1.8Ni - 0.25Mo (0.35 - 0.40C) (4337)-UNS G43370

SAE AMS 7304E

Springs, Steel 0.85 - 1.05C Hardened and Tempered After Forming-UNS G10950

SAE AMS 7510B

Magnets, Rare-Earth/ Cobalt, Permanent Powder-Metallurgy Product

SAE AMS 1376B

Remover, Epoxy Paint Acid-Type, Thickened

SAE AMS 3243F

Chloroprene (CR) Rubber Flame Resistant 55 - 65

SAE AMS 3649C

Film, Polychlorotrifluoroethylene (PCTFE) Unplasticized

SAE AMS 3678/10

Type 10 Virgin Polytetrafluoroethylene (PTFE) Moldings or Extrusions with 15% Carbon Fiber

SAE AMS 3798/1B

Webbing, Low Modulus Aramid 9/16 (14) Wide, 500 (2224) Breaking Strength Herringbone Twill, Resin Treated

SAE AMS 3803A

Wipes, Cotton, Loosely Woven

SAE AMS 4065K

Aluminum Alloy, Drawn Seamless Tubing 1.2Mn - 0.12Cu (3003-0) Annealed

SAE AMS 4174D

Aluminum Alloy, Flash Welded Rings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T73) Solution and Precipitation Heat Treated-UNS A97075

SAE AMS 4259A

Aluminum Alloy, Sheet 2.4Li - 1.3Cu - 0.95Mg - 0.10Zr (8090-T6) Solution and Precipitation Heat Treated (Unrecrystallized)-Reaffirmed Noncurrent April 2006

SAE AMS 4275D

Castings, Permanent Mold 6.2Sn - 1Cu - 1Ni Stress Relieved-Reaffirmed Noncurrect April 2006

SAE AMS 4720E

Wire, Phosphor Bronze 94Cu - 5.0Sn - 0.19P Cold Drawn, Spring Temper (H08)-UNS C51000

SAE AMS 4820E

Bearings, Leaded Copper 70 Cu - 28.5Pb Steel Back-UNS C98400

SAE AMS 5333F

Steel, Investment Castings 0.50Cr - 0.55Ni - 0.25Mo (0.11 - 0.17C) (SAE 8615) Normalized-UNS J11442

SAE AMS 5788F

Cobalt Alloy, Corrosion and Heat Resistant, Hard Facing Rods and Wire 62Co - 29Cr - 4.5W - 1.2C-UNS R30006

SAE AMS 5829E

Nickel Alloy, Corrosion and Heat-Resistant, Welding Wire 56Ni - 19.5Cr - 16.5Co - 2.5Ti - 1.5A1 Vacuum Induction Melted-UNS N07090

SAE AMS 5932B

Steel, Corrosion and Heat-Resistant, Bars, Forgings and Tubing 14.5Cr - 2.3Ni - 12.5Co - 4.0Mo - 0.60V - 0.03Cb(Nb) Carburizing, Premium Aircraft-Quality, Double Vacuum Melted-UNS S42640

SAE AMS 5950B

Nickel Alloy, Corrosion and Heat-Resistant, Sheet and Strip 52.5Ni - 19Cr - 3.0Mo - 5.0Cb - 0.90Ti - 0.50AI - 18Fe Vacuum Induction and Consumable Electrode Melted Solution Heat Treated, Precipitation Hardenable-UNS N07719

SAE AMS 1448A

Sand, Airport Snow and Ice Control

SAE AMS 1630C

Cleaner, Carpet Shampoo Type

SAE AMS 2223H

Tolerances Copper and Copper Alloy Seamless Tubing

SAE AMS 3020A

Oil, Reference, for

SAE AMS 3125F

Enamel, Glyceryl Phthalate, Engine Gray Baking-REAF Non-current Feb 2004

SAE AMS 3126C

Aluminum Coating Material, Corrosion and Heat Resistant Thermosetting, Inorganic Binder

SAE AMS 3336D

Silicone (PVMQ) Rubber Extreme-Low-Temperature Resistant 55 - 65

SAE AMS 3363D

Silicone Rubber Compound Room Temperature Vulcanizing, 50,000 Centipoise Viscosity Durometer 30 - 45

SAE AMS 3813/3A

Rope, Aramid Fiber, Jacketed Parallel Yarn, Braided Jacket

SAE AMS 4063D

Aluminum Alloy, Clad One Side, Sheet 1.25Mn - 0.12Cu (No. 11-0 Brazing Sheet) Annealed-UNS A83003

SAE AMS 4210K

Aluminum Alloy, Castings 5.0Si - 1.2Cu - 0.50Mg (355.0-T51) Precipitation Heat Treated-UNS A03550

SAE AMS 4767F

Silver Alloy, Brazing Filler Metal 92.5Ag - 7.2Cu - 0.22Li 1435 to 1635 Degrees F (779 to 891 Degrees C) Solidus-Liquidus Range-UNS P07925

SAE AMS 5365D

Steel Castings, Sand, Corrosion and Heat Resistant 24.5Cr - 20.5Ni Solution Heat Treated-UNS S92411

SAE AMS 5373D

Alloy Castings, Sand, Corrosion and Heat Resistant 16Co-29Cr-4.5W as Cast-UNS R30006

SAE AMS 5710F

Steel, Bars and Forgings, Corrosion and Heat-Resistant 20Cr - 2.2Si - 1.3Ni (0.76 - 0.86)-(Composition similar to UNS S65006)

SAE AMS 5793B

Powder, Plasma Spray 95Ni - 5Al

SAE AMS 5865D

Nickel, Corrosion and Heat Resistant, Sheet and Strip Thoria Dispersion Strengthened 2.2Th02-UNS N03260

SAE AMS 6264J

Steel, Carburizing Grade, Bars, Forgings, and Tubing 1.2Cr - 3.2Ni - 0.12Mo (0.14 - 0.20C) (SAE 9317)-UNS K44414

SAE MAM 2300D

Steel Cleanliness, Premium Aircraft-Quality Magnetic Particle Inspection Procedure Metric (SI) Measurement

SAE AMS 2601G

Pressure Testing, Gaseous Media 10 psi

SAE AMS 3678/4

Type 4 25% Glass Filled Virgin Polytetrafluoroethylene (PTFE) Moldings or Extrusions

SAE AMS 3695/1

Adhesive Film, Epoxy-Base, High Durability for 95 Degrees C (200 Degrees F) Service

SAE AMS 3798/16B

Webbing, Low Modulus Aramid 1-1/2 (38) Wide, 1700 (7562) Breaking Strength Special Weave

SAE AMS 3837D

Cloth, Type

SAE AMS 3892/12

Tow, Carbon Fiber for Structural Composites 730 (5033) Tensile Strength, 41 (283) Tensile Modulus

SAE AMS 3894/11A

Carbon Fiber Tape and Sheet Epoxy Resin Impregnated G 200,000 (1379) Tensile, 18,000,000 (124) Modulus, 80 (176)

SAE AMS 4068D

Aluminum Alloy, Drawn Seamless Tubing 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti (2219-T3511) Solution Heat Treated and Stress Relieved by Stretching-UNS A92219

SAE AMS 4159D

Aluminum Alloy, Extrusions 7.7Zn - 2.4Mg - 1.6Cu - 0.16Cr (7049-T76511) Solution Heat Treated, Stress Relieved, Straightened, and Overaged-UNS A97049

SAE AMS 4277A

Aluminum Alloy, Sheet 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-0) Annealed, Fine Grained-UNS A97075

SAE AMS 4870F

Aluminum Bronze, Centrifugal and Chill Castings 85Cu - 11Al - 3.6Fe As Cast

SAE AMS 5359E

Steel Castings, Sand, Corrosion and Heat Resistant 15Cr - 4.0Ni - 2.3Mo - 0.08N Solution Heat Treated-UNS J92001

SAE AMS 5361E

Steel Castings, Sand and Centrifugal, Corrosion and Heat Resistant 18.5Cr - 13.5Ni - 2.1Mo Solution Heat Treated-UNS J93072

SAE AMS 5380F

(R) Cobalt Alloy, Corrosion and Heat Resistant, Investment Castings 50.5Co - 26Cr - 15Ni - 6.0Mo as Cast-UNS R30030

SAE AMS 5762E

Steel, Corrosion Resistant, Bars, Wire, and Forging 5.8Mn - 17Cr - 5.8Ni - 2.0Cu - 0.26S Free Machining, Solution Heat Treated-UNS S20300

SAE AMS 5766D

Alloy, Corrosion and Heat-Resistant, Bars and Forgings 21Cr - 32.5Ni - 0.38Ti - 0.38Al - 45Fe Solution Heat Treated-UNS N08800

SAE AMS 5769F

Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings, 21Cr - 20Ni - 20Co - 3.0Mo - 2.5W - 1.0(Cb+Ta) - 0.15N - 32Fe Solution Heat Treated-UNS R30155

SAE AMS 5854A

Nickel Alloy, Corrosion and Heat-Resistant, Bars, Wire, Forgings, and Rings 61Ni - 20.5Cr - 8.5Mo - 3.4Cb - 1.3Ti - 5.0Fe Consumable Electrode or Vacuum Induction Melted Solution Heat Treated-UNS N07716

SAE AMS 6463C

(R) Wire, Steel Welding 18.5Ni - 8.5Co - 5.2Mo - 0.72Ti - 0.10Al Vacuum Melted, Environment Controlled Packaging-UNS K93130

SAE AMS 3107/2A

Primer, Adhesive, Corrosion-Inhibiting High Durability Epoxy, -55 Degrees to +120 Degrees C (-67 Degrees to +248 Degrees F)

SAE AMS 3168

Aqueous Cleaners for Cleaning Prior to Application of Sealing Compounds

SAE AMS 3373/2A

Compound, Silicone Rubber, Insulating and Sealing Oil and Reversion Resistant, Medium Viscosity, Room Temperature Cure

SAE AMS 3678/8

Type 8 Virgin Polytetrafluoroethylene (PTFE) Moldings or Extrusions with 10% Carbon Fiber

SAE AMS 3755/1A

Powder, Fumed Silicon Dioxide Thickening Efficiency 120

SAE AMS 3798/10B

Webbing, Low Modulus Aramid 1 (25) Wide, 6000 (26,689) Breaking Strength Herringbone Twill

SAE AMS 3892/7A

Tow or Yarn, Carbon Fibers For Structural Composites GF (0X) 400 (2758) Tensile Strength, 33 (228) Tensile Modulus

SAE AMS 4206A

Aluminum Alloy, Plate (7055-T7751) 8.0Zn - 2.3Cu - 2.0Mg - 0.16Zr Solution Heat Treated, Stress Relieved, and Overaged-UNS A97055

SAE AMS 4922B

Titanium Alloy, Seamless, Hydraulic Tubing 15V - 3.0Cr - 3.0Al - 3.0Sn Cold Worked and Precipitation Heat Treated

SAE AMS 4955F

Titanium Alloy, Welding Wire 8AI - 1Mo - 1V-UNS R54810

SAE AMS 5384E

Alloy Castings, Investment, Corrosion and Heat Resistant 53Ni - 18Cr - 18Co - 4.0Mo - 2.9Ti - 2.9Al - 0.006B Vacuum-Melted, Vacuum-Cast, Solution and Precipitation Heat Treated-UNS N07500

SAE AMS 5392M

Alloy Iron Castings, Sand, Moderate Corrosion and Heat Resistant 2.1Cr - 15Ni - 6.5Cu (2.4 - 2.8C) as Cast-UNS F47004

SAE AMS 5606E

Alloy, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 41.5Ni - 16Cr - 37Fe - 2.9Cb - 1.8Ti Consumable Electrode or Vacuum Induction Melted 1750 °F (954 °C) Solution Heat Treated-UNS N09706

SAE AMS 5746F

Alloy, Corrosion and Heat-Resistant, Bars and Forgings 15Cr - 45Ni - 4.1Mo - 4.1W - 3.0Ti - 1.0Al - 31Fe (D979) Consumable Electrode Vacuum Melted Solution and Precipitation Heat Treated-Composition similar to UNS N09979

SAE AMS 5846B

Alloy, Corrosion and Heat-Resistant, Bars and Forgings 53Ni - 15Cr - 18.5Co - 5.0Mo - 3.2Ti - 4.2Al - 0.03B Double Vacuum Melted Solution, Stabilization, and Precipitation Heat Treated-Composition similar to UNS N13020

SAE AMS 5867A

Steel, Corrosion and Heat Resistant, Forgings 12.5Cr (SAE 51410) Enhanced Fracture Toughness, Annealed-UNS S41000

SAE AMS 7301G

Steel, Highly-Stressed Springs 0.95Cr - 0.20V (0.48 - 0.53C) (SAE 6150) Case Hardened-UNS G61500

SAE AMS 2451/6A

Plating, Brush, Copper General Purpose

SAE AMS 3362C

Silicone Rubber Compound Room Temperature Vulcanizing, 15,000 Centipoise Viscosity Durometer 35 - 55

SAE AMS 3571B

Resin, Polyether Urethane (EU) Casting Flexible, Solid, Unfilled-FSC 9320

SAE AMS 3683A

Tubing, Irradiated Modified Fluoropolymer Plastic, Electrical Insulation Flame Resistant, Flexible, Heat-Shrinkable, 2 to 1 Shrink Ratio

SAE AMS 3798/14B

Webbing, Low Modulus Aramid 1-1/4 (32) Wide, 800 (3,559) Breaking Strength Herringbone Twill

SAE AMS 3829B

Cloth, Type

SAE AMS 3920A

Acceptance Criteria Adhesive-Bonded Metal-Faced Sandwich Structures

SAE AMS 4193C

Aluminum Alloy Sheet and Plate 4.4Cu - 1.5Mg - 0.60Mn (2024-T861) Solution Heat Treated, Cold Worked, and Precipitation Heat Treated-UNS A92024

SAE AMS 4306B

Aluminum Alloy, Plate 6.4Zn - 2.4Mg - 2.2Cu - 0.12Zr (7150-T6151) Solution Heat Treated, Stress Relieved, and Aged-UNS A97150

SAE AMS 4575E

Nickel-Copper Alloy Tubing, Brazed, Corrosion Resistant 67Ni - 31Cu Annealed-UNS N04400

SAE AMS 4873F

Aluminum Bronze Alloy, Sand Castings 85Cu - 11Al - 3.6Fe Solution Heat Treated and Tempered-Composition similar to UNS C95420

SAE AMS 5394D

Alloy Iron Castings, Ductile, Sand, Corrosion and Heat Resistant 2.0Cr - 20Ni (2.4 - 3.0C) Stress Relieved-UNS F47006

SAE AMS 5703D

Nickel Alloy, Corrosion and Heat Resistant, Bars, Forgings, and Rings 41.5Ni - 16Cr - 37Fe - 2.9Cb - 1.8Ti Consumable Electrode or Vacuum Induction Melted 1750 Degrees F (954 Degrees C) Solution, Stabilization, and Precipitation Heat Treated-UNS N09706

SAE AMS 7260E

Rings, Butadiene-Acrylonitrile (NBR) Rubber, Molded Fuel and Low Temperature Resistant 70 - 80

SAE AMS 7702E

Nickel-Iron Alloy, Magnetic, Sheet and Strip Cold Rolled, Half-Hard Temper

SAE AMS 1378A

Compound, Carbon Soil and Paint Remover Aircraft Turbine Engine Components Room Temperature Application

SAE AMS 1387A

Remover, Anti-Galling Compound Aircraft Turbine Engine Components Room Temperature Application

SAE AMS 1523A

Cleaner for Exterior Aircraft Surfaces Thickened or Gel-Type, Water-Base

SAE AMS 2451/11A

Plating, Brush, Cobalt

SAE AMS 2483B

Blackening Solution for Aluminum Touch-Up Solution

SAE AMS 2695C

Connections, Electrical Solderless, Wire-Wrapped

SAE AMS 3146

Coating, Interior Aircraft Cabin Low Heat and Smoke Release

SAE AMS 3678/6

Type 6 60% Bronze Filled Virgin Polytetrafluoroethylene (PTFE) Moldings or Extrusions

SAE AMS 3710C

Sandwich Structures, Glass Fabric-Resin Low Pressure Molded, Heat Resistant

SAE AMS 3718B

Webbing, Woven Nylon For Decelerators

SAE AMS 3894/2B

Carbon Fiber Tape and Sheet Epoxy Resin Impregnated G 150,000 (1034) Tensile, 20,000,000 (138) Modulus, 175 (347)

SAE AMS 4056G

Aluminum Alloy, Sheet and Plate 4.4Mg - 0.70Mn - 0.15Cr (5083-0) Annealed-UNS A95083

SAE AMS 4203C

Aluminum Alloy, Plate 6.2Zn - 1.8Cu - 2.4Mg - 0.13Zr (7010-T7351) Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated (UNS A97010)

SAE AMS 4247B

Aluminum Alloy, Hand Forgings 7.7Zn - 2.4Mg - 1.6Cu - 0.16Cr (7049- T7352) Solution Heat Treated, Stress Relieved by Compression, and Precipitation Heat Treated-UNS A97049

SAE AMS 4254B

Aluminum Alloy, Aramid Fiber Reinforced, Laminated Sheet 4.4Cu - 1.5Mg - 0.6Mn (2024-T3) 3, 5, 7, or 9 Ply

SAE AMS 4307B

Aluminum Alloy, Extrusions 6.4Zn - 2.4Mg - 2.2Cu - 0.12Zr (7150-T61511) Solution Heat Treated, Stress Relieved by Stretching, Straightened, and Precipitation Heat Treated

SAE AMS 4319B

Aluminum Alloy, Rolled or Cold Finished, Bars and Rods 12.2Si - 1.0Mg - 0.90Cu - 0.90Ni (4032-T651) Solution Heat Treated, Stress-Relieved, and Artificially Aged-UNS A94032

SAE AMS 4321A

Aluminum Alloy Forgings 7.7Zn - 2.5Mg - 1.5Cu - 0.16Cr (7049-01) High Temperature Annealed

SAE AMS 4420N

Magnesium Alloy Castings, Sand 6Al - 3Zn (AZ63A-F) as Cast-UNS M11630

SAE AMS 5036H

Steel Sheet and Strip, Aluminum Coated Low Carbon-Reaffirmed Non-current February 2006

SAE AMS 5225E

Iron-Nickel Alloy Strip 49Fe - 5.3Cr - 42Ni - 2.5Ti - 0.55Al Solution Heat Treated, Cold Rolled, 50% Reduction-UN N09902

SAE AMS 5650F

Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Tubing, and Rings 23Cr - 13.5Ni (SAE 30309S) Solution Heat Treated-UNS S30908

SAE AMS 5780E

Steel, Corrosion and Heat Resistant, Welding Wire 15.5Cr - 4.5Ni - 2.9Mo - 0.10N-UNS S35500

SAE AMS 5889B

Nickel Alloy, Corrosion and Heat Resistant, Sheet and Strip 54Ni - 22Cr - 12.5Co - 9.0Mo - 1.2Al Consumable Electrode or Vacuum Induction Melted Annealed-UNS N06617

SAE AMS 7724C

Alloy Sheet and Strip, Sintered Wire Mesh, Corrosion and Heat Resistant 30Fe - 1.5Mn - 21Cr - 20Ni - 20Co - 3.0Mo - 2.5W - 1.0(Cb +Ta) - 0.15N Porous-UNS R30100; Reaffirmed Non-current April 2006

SAE AMS 7905B

Beryllium Bars, Rods, Tubing, and Shapes Optical Grade

SAE AMS 7907B

Beryllium Bars, Rods, Tubing, and Shapes Instrument Grade

SAE AMS 1532C

Cleaner for Aircraft Exterior Surfaces Wipe-On, Wipe-Off, Emulsion-Type

SAE AMS 3120F

Enamel, Glyceryl Phthalate, Black Baking-REAF Non-current Feb 2004

SAE AMS 3217/7

TEST SLABS, HIGH STRENGTH, FLUOROSILICONE (FVMQ) 55 - 65

SAE AMS 3272/1A

Cloth, Nylon, Polyurethane Coated Plain Weave, 6.0 Ounces/Square Yard (200 g/m2)

SAE AMS 3370A

Silicone Resin, Elastomeric, Transparent Room Temperature Cure

SAE AMS 3634D

Tubing, Polyolefin Plastic, Electrical Insulation Selectively Crosslinked, Semi-Rigid, Heat-Shrinkable

SAE AMS 3678/5

Type 5 Virgin Polytetrafluoroethylene (PTFE) Moldings or Extrusions with Pigment

SAE AMS 3805A

Cloth, Duck, Aramid (META), Non-Melting

SAE AMS 3849B

Cloth, Quartz, Style 581 Fabric Hot-Melt, Addition-Type, Polyimide Resin Impregnated

SAE AMS 3906B

Glass Tape and Flat Sheet, Non-Woven Cloth Epoxy Resin Impregnated, for Hand and Machine Layup

SAE AMS 4803D

Zinc Alloy Castings, Die 4.0Al - 0.04Mg (AG40A) as Cast

SAE AMS 4937B

Titanium Alloy, Extrusions and Flash Welded Rings 6Al - 6V - 2Sn Beta Extruded Plus Annealed, Heat Treatable-UNS R56620

SAE AMS 5717H

Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 45.5Ni - 25.5Cr - 3.2Co - 3.2Mo - 3.2W - 18.5Fe Solution Heat Treated-UNS N06333

SAE AMS 6356F

Steel, Sheet, Strip, and Plate 0.95Cr - 0.20Mo - (0.30 - 0.35C)(SAE 4132)-UNS G41300

SAE AMS 6473A

Steel Welding Wire 0.88Cr - 1.8Ni - 1.6Co - 0.42Mo - 0.08V - (0.28 - 0.33C) (SAE 4330V) Vacuum Melted, Environment Controlled Packaging-Reaffirmed Noncurrent July 2001

SAE AMS 7909

Aluminum Beryllium, NNS Preforms Hot Isostatic Pressed 38Al - 62Be

SAE AMS-C-22587

Cartridges, Grease, 14 Ounce (for Cartridge-Type Grease Gun)-FSC 4930; Should Be Used Instead of MIL-C-22587B, Which Was Cancelled on 30 August 1999

SAE AMS-G-81827

Grease, Aircraft, High Load Capacity, Wide Temperature Range-Replaces MIL-G-81827

SAE AMS-H-6088C

Heat Treatment of Aluminum Alloys

SAE AMS-R-3065

Rubber, Fabricated Products

SAE MAM 2262D

Tolerances, Metric Nickel, Nickel Alloy, and Cobalt Alloy Sheet, Strip, and Plate

SAE AMS 3060A

Compound, Rust Inhibiting Aircraft Engine Components

SAE AMS 3217/3B

Test Slabs, Chloroprene (CR) 65 - 75

SAE AMS 3626F

Plastic Moldings and Extrusions, Methyl Methacrylate

SAE AMS 3664B

Cloth, Glass, Vinyl Coated

SAE AMS 3718/5A

Webbing, Woven Nylon for Decelerators 1 (25) Wide, 9000 (40,000) Breaking Strength

SAE AMS 3731/7B

Potting Compound, Epoxy Bisphenol A-Type Filled, Room Temperature Cure, Low Shrinkage

SAE AMS 3778A

Tape and Webbing, Woven, Nylon

SAE AMS 3779/1A

Tape, Adhesive, Pressure-Sensitive Thermal Radiation Resistant, Aluminum Foil/Glass Cloth

SAE AMS 3787/2A

Thread, Para-Aramid Intermediate Modulus 6700 Yards per Pound (13,507 m/kg), 25 Pounds Force (111 N) Breaking Strength