IHS Inc. The Source for Critical Information and Insight
All Industries |  Change  

Go
 
 

Frost: GDP Growth, Rising Energy Demands Drive N. American Water Treatment in Power Industry

June 9, 2008 // Published as a news service by IHS

 
IHS Sells Standards & Regulations
Environment/Safety/Health solutions from IHS include current & historical codes, regs & standards from gov't, int'l & industry sources.
Complete this form for a free quote.
CyberRegs - Compliance library
ASTM / NFPA / ASME / ISO
API / ASSE / AWS / NEMA / UL
Safety Compliance Collection
Environment Compliance Collection
First Name:

Last Name:

Email address:
The North American market for water treatment systems in the power industry is extremely competitive, with price being a key factor.

According to Frost & Sullivan, the market for wastewater treatment systems gains momentum because of increasingly stringent surface discharge standards and growing concerns over declining fresh water resources.

Analysts said advanced technologies such as zero liquid discharge (ZLD) and flue gas desulphurization (FGD) blow down treatment devices continue to be mainstays in the wastewater treatment sector.

Recent analysis from Frost & Sullivan of the North American market for water treatment in the power industry found earned revenues of $580 million in 2006, with estimates to reach $1.17 billion in 2013.

"Gross domestic product [GDP] growth, rising energy demand and an increasing requirement for a reliable water treatment system in a power plant are all driving the growth of the North American market for water treatment in the power industry," said Frost & Sullivan research analyst Shilpa Tiku.

"Although the cost of a water treatment system relative to the total investment of the plant is quite small, power plants need to maintain an excellent water treatment system, otherwise the plant would have to close, or water hardness could cause extensive damage to the plant prior to shutdown."

There is a rise in the construction of coal-fired power plants, analysts said, which consume very large volumes of water for steam production and cooling. In addition, many plants exceeding 30 years must be retrofit with newer technologies.

The water treatment technologies for new plants are likely to depend on the feed water source and impurities in it, while for the old plants, the technology itself is determined based on the age of the plant. Analysts said stringent discharge standards are, however, a crucial challenge for power plants as they necessitate the installation of expensive, advanced treatment technologies.

"While strict air emission norms led plants to install the FGD process using wet scrubbing, this has caused wastewater discharge from the FGD process, which poses a challenge to the utilities," said Tiku. "Discharging FGD blow down water is not very easy, as the constituents are very complex and the standards are tough to meet."

Thermal wastewater treatment process helps treat FGD blow down for recycling and reusing the wastewater. In the thermal process, water goes through various stages of treatment to emerge as almost pure water.

Analysts said the concentrate left behind by the thermal process contains contaminants that are much smaller in volume than earlier contaminants and can be treated by biodegradation, digestion or other residual solids mitigation technologies that are available in the market.

Since it is a capital-intensive technology, analysts said utilities are hesitant to invest large amounts of money in it.

Source: Frost & Sullivan.

ENGINEERING STANDARDS & REGULATIONS NEWS
November 18, 2009
ANSI/ASSE Z359.0 Revises Workplace Fall Protection Guidelines
The American Society of Safety Engineers (ASSE) revised American National Standards Institute (ANSI)/ASSE Z359.0-2009 - Definitions and Nomenclature ... more
November 5, 2009
ISO, ILAC, IAF Streamline Quality Mgmt. Requirements for Medical Labs
In a joint communiqué by the International Organization for Standardization (ISO), the International Laboratory Accreditation Cooperation (ILAC) ... more
October 30, 2009
ASTM D7558 Addresses Medical Glove Allergens
ASTM International issued a standard that allows rubber glove manufacturers to monitor the level of residual chemicals in their end products ... more
October 30, 2009
ANSI Begins Accreditation Under Toy Safety Certification Program
The American National Standards Institute (ANSI) accredited five certification bodies under the new Toy Industry Association (TIA) Toy Safety ... more
October 23, 2009
EU-China Standards Information Platform Launched
The European Committee for Standardization (CEN) announced the official launch of the new EU-China Standards Information Platform, a project ... more
Show All..